Hookup Diagram; Reset Button - Altronix AL602ULADA Installation Manual

Fig. 2
5A
250V
line
ground
neutral
Fire
Alarm
Non-Supervised
Control
Panel
(FACP)
-- AUX +
Fuse
Cover
SW2 SW1
+ OUT1 --
+ OUT2 --
unswitched 120VAC
power mains
(non-power limited)
L
line
Regulated Power-Limited Outputs
ground
EOL
2.5 amp max. per
+
Resistor
output in alarm
from
Green Lead
FACP
(total= 6.5 amp)
-- (Supervised)
Supervision Relay -- AUX +
(Not Supplied)
+
SW2 SW1
--
+ OUT1 --
AL602ULADA
Fig. 2a
AC Local
Use separate knockout. Keep 1/4" spacing from
non power limited wiring
unswitched 120VAC -- DC +
OUT1
INPUT SELECT
power mains
TEMPORAL
(non-power limited) STROBE SYNC
IN > OUT SYNC
OUT2
250V
INPUT SELECT
TEMPORAL
Green Lead
line
STROBE SYNC
ground
RESET
IN > OUT SYNC
+
4-wire Smoke
Non-Supervised
Detector
--
10A
+ OUT4 --
+ OUT3 --
250V
+
4-wire Smoke
IN1+ IN1--
Detector
G N SW2 SW1
RET1+ RET1--
--
Use separate knockout.
Supervised Non-Supervised
Keep 1/4" spacing from
non power limited wiring
neutral
Regulated Power-Limited Outputs
EOL Power
-- DC +
RESET
+ OUT4 --
+ OUT2 -- + OUT3 --
Power Limited Outputs
2.5 amp per
output in alarm
(total=10 amp)

Hookup Diagram:

Divider
OUT3
OUT1 OUT2 OUT3 OUT4
NO C NC NO C NC
BAT FAIL
AC FAIL
INP1 INP2
DC
5A
OUT4
J2
AC Local
Use separate knockout. Keep 1/4" spacing from
neutral
non power limited wiring
AC
-- AUX + -- DC + OUT1
INPUT SELECT
TEMPORAL
STROBE SYNC
15A
IN > OUT SYNC
OUT2
INPUT SELECT
250V
TEMPORAL
STROBE SYNC
RESET
IN > OUT SYNC
IN2+
IN2-- C "DRY1" NC + BAT --- + DC ---
UPPER TERMINALS
RET2+ RET2-- C "DRY2" NC LOWER TERMINALS
+ OUT1 -- + OUT3 -- + OUT4 --
+ OUT2 --
IN1+ IN1--
RET1+ RET1--
Supervised Non-Supervised
2.5 amp max. per
output in alarm
Addressable
(total= 6.5 amp)
OUT1 OUT3
(Supervised)
Control Module
INPUT SELECT
TEMPORAL
OUT1 OUT2 OUT3 OUT4
STROBE SYNC
Trigger Output
IN > OUT SYNC
INP1 INP2
OUT2 OUT4
See Note 2
INPUT SELECT
Trouble Memory
TEMPORAL
STROBE SYNC
IN > OUT SYNC

Reset Button

Fig. 2c
IN1+ IN1-- IN2+
IN2-- C "DRY1" NC UPPER TERMINALS
RET1+ RET1-- RET2+ RET2-- C "DRY2" NC LOWER TERMINALS
Green Lead
This connection is used to
monitor AC and Bat Fail and
will cause a simultaneous trouble
FAULT
condition to the FACP's IN1 and IN2
Divider
OUT3
OUT1 OUT2 OUT3 OUT4
Common trouble output to
INP1 INP2
OUT4
FAULT Digital Communicator or
Local Annunciator Dry output Contact
(Form "C" contacts) ( Non-Supervised)
IN2+ IN2-- C "DRY1" NC
UPPER TERMINALS
RET2+ RET2-- C "DRY2" NC LOWER TERMINALS
Addressable
Control Module
Trigger Output
These circuits are used to
See Note 2
FAULT
monitor AC and Bat Fail and
will cause a simultaneous trouble
condition to the FACP's IN1 and IN2
Digital Communicator or
Local Annunciator Dry output Contact
(Form "C" contacts)
Addressable
Control Module
Trigger Output
See Note 2
Non-Supervised
Green Lead
This connection is used to
monitor AC and Bat Fail and
will cause a simultaneous trouble
condition to the FACP's IN1 and IN2
Non-Supervised
Common trouble output to
Digital Communicator or
Local Annunciator Dry output Contact
(Form "C" contacts) ( Non-Supervised)
Common trouble
Input/Output
Fig. 2b
- 7 -