Modifiers - Kenmore 110.4292 Owner's Manual & Installation Instructions

Stain Treat
Use this option for heavily soiled loads that need improved stain
treatment. When Stain Treat is selected, the water temperature of
the selected wash cycle is automatically set to warm. The water
will then be heated to a hot water temperature to aid in stain
removal. This option will provide optimal removal of organic
stains such as blood.
NOTE: If Stain Treat is selected with the Sanitary cycle, the water
will be heated to a very hot temperature.
Auto Soak
Use the Auto Soak option for loads of heavily soiled cotton, linen,
polyester or nylon with set-in stains. During Auto Soak, water will
be added to the drum and the laundry will be equally distributed
by a short tumbling phase. Laundry will then be soaked by
phases without drum movement. After soaking, the washer
drains without spinning.
Added to a Wash Cycle: A 30 minute soak time is added to the
main wash cycle to improve removal of set-in stains.
1. Add detergent to both the Prewash and Main Wash
compartments of the Dispenser Drawer.
NOTE: The Auto Soak and Prewash options cannot be
selected in the same cycle. Use powdered detergent for the
main wash cycle because liquid detergent will seep into the
washer during Auto Soak.
2.
3.
Select a Wash Cycle.
Select AUTO SOAK.
NOTE: For cycles with hot wash temperatures, the soak
temperature will be set to warm; otherwise, the soak
temperature will be the same as the wash temperature.
4. Select and hold START (approximately 1 second). After
soaking, the washer drains and the wash cycle starts.
Without a Wash Cycle: Provides a soak time with warm or cold
water followed by drain.
1. Add detergent only to the Prewash compartment of the
Dispenser Drawer.
2. Select DRAIN/SPIN or RINSE/SPIN first, then AUTO SOAK.
3. Choose the desired soak temperature.
4. Select and hold START (approximately 1 second).
2nd Rinse
A second rinse can be used to ensure the removal of detergent or
bleach residue from garments. This option provides an additional
rinse with the same water temperature as the first rinse.
Extended Spin
Use this option to add an additional spin to any cycle to improve
drying times for some heavy fabrics or special-care items by
reducing excess water, which may save energy.
Preset cycle settings of Water Temperature, Wash/Rinse, and
Spin Speed can be changed. You can change a modifier after
starting a cycle anytime before the selected Modifier begins. Not
all Modifiers are available with all options and cycles.
MODRFIERS
AUTOTrMP COrVT_OI
• EXTRA HOT/COLD @ EXTRA HIGH
o HOT! COLD
@ HUGH
@ WARM ! WARM @ MEDIUM
@ WARM / COLD @ LOW 0 HUGH
@ COLD / COLD @ EXTRA LOW @
LOW
0 TAP COLD / COLD 0 NO SPIN @ OFF
C) (2) C)
WATER TEMP SPUN SPEED END of CYCLE SUGNAL
WASH / RINSE
To change the water temperature, select the WATER TEMP
button until the desired setting
glows.
To change the spin speed, select the SPIN SPEED button
until the desired setting glows.
HEAVY
® NORMAL
® LIGHT
C)
SOIL LEVEL
• To change cycle time, select SOIL LEVEL button.
• To change the loudness of the End of Cycle Signal, select
END of CYCLE SIGNAL.
Wash/Rinse Temp
Select a water temperature based on the type of load you are
washing. Use the warmest wash water safe for fabrics. Follow
garment label instructions.
Warm rinses leave the loads dryer than cold rinses. Warm rinses
increase wrinkling. In cold climates, a warm rinse makes the load
more comfortable to handle. Cold rinses save energy.
Temperature Guide
Wash Water Temperature Suggested Fabrics
Extra Hot Sturdy colorfast fabrics
153°F (67°C) Heavy soils
HOT* Whites and pastels
140°F (60°C) Heavy soils
WARM Bright colors
104°F (40°C) Moderate to light soils
COLD Colors that bleed or fade
77°F (25°C) Light soils
In wash water temperatures colder than 70°F (21 °C),
detergents do not dissolve well. Soils may be difficult
to remove.
*When used with Stain Treat option, the water is heated
gradually to assist in the removal of organic soils such
as blood.
16