Mitsubishi 2013 Outlander Service Manual page 103

Hide thumbs Also See for 2013 Outlander:
Table of Contents

Advertisement

DECELERATION FUNCTION
1. When the SET − switch is pressed and held for
approximately 0.5 second or longer during the
constant speed driving, the vehicle is decelerated
by using engine braking while the switch is
pressed.
2. After that the SET − switch is released, the vehicle
speed of that time is newly stored, and then the
constant speed driving is performed at that speed.
The speed limiter will store a set vehicle speed,
and then regulate the vehicle speed within that
stored speed.
3. In addition, when the SET − switch is pressed for
less than approximately 0.5 second, the vehicle
speed is decreased by approximately 1.6 km/h
from the constant speed driving speed. The
decelerated speed is newly stored, and then the
constant speed driving is performed at that speed.
Every time the SET−switch is pressed briefly
(within approx. 0.5 seconds), the speed limiter will
store a lower vehicle speed by 1 km/h. The speed
limiter will regulate the vehicle speed within that
last stored speed.
4. When the SET − switch is pressed and held, and
the vehicle speed is decelerated to low speed limit
(approximately 40 km/h) , the low speed limit will
be maintained.
RESUME FUNCTION
1. During the constant speed driving, press the
CANCEL switch, or depress the brake pedal to
cancel the constant speed driving. The speed
limiter will be deactivated by pressing the
CANCEL switch.
2. Afterward, when the RES + switch is pressed
while driving at a vehicle speed of low speed limit
(approximately 40 km/h) or more, a constant
speed driving is performed at the vehicle speed
stored when the constant speed driving was
cancelled.
ACCELERATION FUNCTION
1. During the constant speed driving, when the RES
+ switch is pressed and held for approximately 0.5
seconds or longer, the vehicle is accelerated with
the specified acceleration while the switch is
pressed.
2. After that the RES + switch is released, the
vehicle speed of that time is newly stored, and
then the constant speed driving is performed at
that speed. The speed limiter will store a set
vehicle speed, and then regulate the vehicle
speed within that stored speed.
ENGINE AND EMISSION CONTROL
CRUISE CONTROL SYSTEM
3. In addition when the RES + switch is pressed for
CANCEL FUNCTION
When any of the following conditions are satisfied,
the constant speed driving will be cancelled. The
speed limiter will be deactivated by pressing the
CANCEL switch.
• The cruise control system is stopped by the
• The CANCEL switch is pressed.
• The brake pedal is depressed.
• The selector lever is shifted to the "N" position.
• The vehicle speed becomes low speed limit
• The vehicle speed is decreased by 15 km/h or
• An abnormality occurs in the vehicle speed sig-
• The ASC is operated.
• An abnormality occurs in CVT-ECU.
• An abnormality occurs in the CAN communica-
EMERGENCY CANCEL FUNCTION
When the accelerator pedal is depressed fully to
drive at higher speed than the stored speed, the
speed limiter will be deactivated temporarily
LAST STATUS MEMORY FUNCTION
<RUSSIA>
The system stores ON/OFF status of the cruise con-
trol when the ignition switch is turned off. Then, when
the ignition switch is turned on the next time, the sys-
tem will resume the stored status.
FAIL-SAFE FUNCTION
When one of the following conditions is met, the
cruise control system function will be suspended until
the system returns to normal condition. Also, when
one of the following conditions is met, a constant
speed driving is cancelled immediately. The speed
limiter will be also deactivated.
• An abnormality occurs in the cruise control
less than approximately 0.5 second, the vehicle
speed is increased by approximately 1.6 km/h
from the constant speed driving speed. The
accelerated vehicle speed is newly stored, and
then the constant speed driving is performed at
that speed. Every time the RES + switch is
pressed briefly (within approx. 0.5 seconds), the
speed limiter will store a higher vehicle speed by 1
km/h. The speed limiter will regulate the vehicle
speed within that last stored speed.
pressing the cruise control ON/OFF switch.
(approximately 40 km/h) or less.
more from the setting vehicle speed.
nal.
tion.
switches.
17-7

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents