Mitsubishi 2015 OUTLANDER SPORT/RVR Owner's Manual

Table of Contents

Quick Links

Download this manual

Introduction

Thank you for buying a MITSUBISHI OUTLANDER SPORT/RVR.

We are confident you will enjoy your vehicle. It has been engineered

for optimum performance, durability and comfort. By thoroughly

reading this Owner's Manual, you will gain an understanding of the

many features that are included in the OUTLANDER SPORT/RVR.

The Owner's Manual contains descriptions and illustrations that will

assist in the operation and maintenance of your vehicle.

Your Authorized Mitsubishi Motors Dealer will be happy to assist you

with any further questions you may have regarding the operation of

your vehicle.

Please note that this manual applies to all OUTLANDER SPORT/RVR

models and explains all features including options. Some features

explained in this manual may not be installed on your vehicle.

Please leave this Owner's Manual in the vehicle at the time of resale.

The next owner will appreciate having access to the information con-

tained here.

This manual includes instructions for standard and optional equipment

available at the time of printing. Mitsubishi Motors Corporation

reserves the right to make changes in design and specifications and to

make additions or improvements in its product without assuming any

obligation to install these on previously manufactured products.

Throughout this manual the words WARNING and CAUTION

appear.

N09200102055

These are reminders to be especially careful. Failure to follow the

instructions could result in personal injury or damage to your vehi-

cle.

Indicates a strong possibility of severe personal injury or death if

instructions are not followed.

Points out hazards or unsafe practices that could cause minor

personal injury or damage to your vehicle.

You will see another important symbol:

NOTE Gives helpful information.

As with other vehicles of this type, failure to operate this vehicle cor-

rectly may result in loss of control or an accident. Be sure to read

"on-pavement" and "off-road" driving guidelines in the "Driving

safety" and "Features and controls" sections.

WARNING

 Engine exhaust, some of its constituents, and certain vehicle compo-

nents contain or emit chemicals known to the State of California to

cause cancer and birth defects and reproductive harm. In addition,

certain fluids contained in vehicles and certain products of compo-

nent wear contain or emit chemicals known to the State of Califor-

nia to cause cancer and birth defects or other reproductive harm.

This vehicle is manufactured by Mitsubishi Motors North America,

Inc. in U.S.A. under license from Mitsubishi Motors Corporation.

I n f o r ma t i o n P r o v i d e d b y :

Table of Contents

Chapters

Table of Contents

Summary of Contents for Mitsubishi 2015 OUTLANDER SPORT/RVR

Page 1 Your Authorized Mitsubishi Motors Dealer will be happy to assist you Points out hazards or unsafe practices that could cause minor with any further questions you may have regarding the operation of personal injury or damage to your vehicle.
Page 2 Table of contents Overview Quick index General information Seat and restraint systems Features and controls Driving safety Comfort controls For emergencies Vehicle care and maintenance Customer assistance/ Reporting Safety Defects Specifications Alphabetical index I n f o r ma t i o n P r o v i d e d b y :...
Page 3 Instruments and controls Instruments and controls N00100202560 Headlight leveling switch (if so equipped) P.5-127 Combination headlights and dimmer switch P.5-121 Turn signal lever P.5-127 Front fog light switch (if so equipped) P.5-128 Instrument cluster P.5-81 Sportronic steering wheel paddle shifter Active stability control (ASC) OFF switch (if so equipped) P.5-53 P.5-69, 5-89...
Page 4 Instruments and controls Mitsubishi Multi-Communication System (if so equipped) DISPLAY AUDIO (if so equipped) Refer to the separated owner’s manual. Audio (if so equipped) P.7-26 Air conditioning P.7-4, 7-9, 7-14, 7-20 Center vents P.7-2 Multi-information meter switch P.5-85 Key slot (if so equipped) P.5-21 Fuses P.9-24...
Page 5 Interior Interior N00100302297 Sun visors P.5-159 Vanity mirror P.5-159 Dome light (rear) (if so equipped) P.5-162 Card holder P.5-159 Dome light (front)/Reading lights Assist grips P.5-169 P.5-162 Coat hook P.5-169 Sunshade switch (if so equipped) P.5-39 ® Bluetooth 2.0 interface microphone (if so equipped) P.5-136 Cargo area cover (if so equipped)
Page 6 Interior Electric remote-controlled outside mirror switch P.5-43 Lock switch P.5-38 Power door lock switch P.5-30 Supplemental restraint system (SRS) - curtain airbags P.4-37 Power window switch P.5-36 Sunshade illumination lamp dimming control switch Seat belts P.4-11 (if so equipped) P.5-163 Adjustable seat belt shoulder anchor P.4-16 Inside rearview mirror P.5-41...
Page 7 Luggage compartment Luggage compartment N00100501508 Spare tire P.8-6 Luggage hooks P.5-170 Luggage hooks P.5-170 Hook Luggage hooks P.5-170 Jack P. 8-5 Tools P.8-5 I n f o r ma t i o n P r o v i d e d b y : Overview...
Page 8 Outside Outside N00100602447 Headlights, low beam P.5-125, 9-29, 9-31 Power window P.5-36 Windshield wipers P.5-129 Engine hood P.9-3 Fuel tank filler P.3-3 Outside rearview mirrors P.5-43 Front turn signal lights P.5-127, 9-29, 9-33 Side turn signal light P.5-127, 9-29, 9-34 Headlights, high beam P.5-125, 9-29, 9-32 Front side-marker lights...
Page 9 Outside Liftgate P.5-32 Antenna P.7-58 High-mounted stop light P.9-29, 9-38 F.A.S.T.-key (Free-hand Advanced Security Transmitter) (if so equipped) P.5-11 Keyless entry system (if so equipped) P.5-24 Rear spoiler Locking and unlocking P.5-28 Rear window wiper P.5-133 Rear-view camera (if so equipped) P.5-79 Tire pressure monitoring system P.5-75 Changing tires P.8-5...
Page 10 Warning lights Do this Ref. Page  Park your vehicle in a safe place and stop the engine. Contact your Mitsubishi Motors dealer or a repair facility of your choice for assis- P. 5-119 tance. Charging system warning light  If this light comes on while driving, check to see that the parking brake is fully released.
Page 11  If the light does not go out after the test, or if it comes on again, we recommend that Anti-lock braking system warning you have the system checked at an authorized Mitsubishi Motors dealer or a repair light facility of your choice as soon as possible.
Page 12 If this problem occurs... If this problem occurs... N00200900867 Problem Do this Ref. Page Cannot turn the key. (except for vehicles equipped with the F.A.S.T.-key) Will not turn from “ACC” to “OFF”. Vehicles with continuously variable transmission (CVT): P. 5-45 Check the position of the selector lever.
Page 13 If this problem occurs... Problem Do this Ref. Page Cannot shift the selector lever from the “P” (PARK) position. Shift the selector lever while pressing the brake pedal. P. 5-49 (for vehicles with continuously Check that the ignition switch or the operation mode is in ON. variable transmission (CVT)) The windows are fogged up.
Page 14 If this problem occurs... Problem Do this Ref. Page The engine coolant temperature display “ ” in the multi-infor- mation display is flashing. Steam comes out of the engine compartment. Type 1 The engine is overheated. P. 8-4 Carefully stop the vehicle in a safe place. Type 2 1.
Page 15 If the warning lights on the multi-information display will not turn off, or if they is slow when the vehicle starts come on frequently, please have the vehicle checked at your nearest Mitsubishi Motors dealer. moving. (for vehicles with CVT) A tire is punctured.
Page 16: Table Of Contents
Filling the fuel tank ................3-3 Modifications to and racing of your vehicle ........3-5 Genuine Mitsubishi Motors parts ............3-6 California Perchlorate Materials Requirements .......3-6 I n f o r ma t i o n P r o v i d e d b y :...
Page 17: Fuel Selection
Gasoline detergent additives is at least as high as that recommended for additive that is blended into some gasolines unleaded gasoline. to increase the octane number. Mitsubishi Motors Corporation recommends using gaso- In the United States, fuel suppliers are lines without MMT.
Page 18: Filling The Fuel Tank
Always Your vehicle may have been designed to sat- Mitsubishi Motors dealer or a repair facility handle fuel in well-ventilated outdoor isfy California’s low-emission regulations of your choice.
Page 19 Filling the fuel tank 3. Open the fuel tank filler pipe by slowly WARNING WARNING turning the fuel tank filler cap counter-  Keep the doors and windows closed while  Since the fuel system may be under pres- clockwise. refueling the vehicle.
Page 20: Modifications To And Racing Of Your Vehicle
Always tighten the fuel tank filler cap until Only Mitsubishi Motors approved acces-  Failure to use Mitsubishi Motors genuine you hear at least 3 clicks. sories should be fitted to your vehicle. parts The indicator will go off after driving several ...
Page 21: Genuine Mitsubishi Motors Parts
Genuine Mitsubishi Motors parts  Using a cellular phone or radio set inside ine parts affects the driving safety of your able from your Mitsubishi Motors dealer are the vehicle without an external antenna Mitsubishi-vehicle. a wide variety of accessories to personalize may cause electrical system interference, your new vehicle.
Page 22 Seat and restraint systems Seats ....................4-2 Seats and restraint systems ..............4-2 Front seats ..................4-3 Rear seats ..................4-7 Head restraints .................4-7 Extending a luggage compartment ..........4-9 Seat belts ..................4-11 Seat belt use during pregnancy ............4-17 Seat belt pre-tensioner and force limiter systems ......4-17 Child restraint systems ..............4-18 Maintenance and inspection of seat belts ........4-26 Supplemental Restraint System (SRS) - airbag ......4-26...
Page 23: Seats
Seats Seats N00408401522 locks also are safety equipment, which must 1 - Front seat Seats and restraint systems be used correctly. N00401600153  To adjust the seat forward or backward  Always check the following before you drive: Your vehicle has seat belts and other features Page 4-3 that help protect you and your passengers in ...
Page 24: Front Seats
Front seats Safety equipment cannot prevent injury or WARNING To adjust the seat forward or death in all motor vehicle accidents. You can backward  To reduce the risk to the driver of serious help reduce the risk of injury or death, how- injury or death during deployment of the ever, by following the instructions in this N00401900228...
Page 25 Front seats Power seat adjustment To adjust the seatbacks Power seat adjustment N00402000268 Operate the switch forward or backward to Operate the switch in the direction of the Manual seat adjustment move the seat to the desired position. Release arrows to adjust the seatback. the switch to lock the seat in place.
Page 26 Front seats WARNING  To reduce the risk of serious injury or death in the event of an accident or sud- den stop, all seatbacks should be kept in the upright position while the vehicle is in motion. Seat belt performance during an accident can be adversely affected if the seatbacks are reclined.
Page 27 Front seats Heated seat WARNING (if so equipped)  Persons who are unable to feel tempera- N00435601405 ture change or skin pain due to age, ill- The heated seats can be operated by pushing ness, injury, medication, alcohol use, the switch when the ignition switch or the fatigue or other physical conditions or operation mode is in ON.
Page 28: Rear Seats
Rear seats CAUTION NOTE WARNING  If water or any other liquid is spilled on the  Never sit on the arm rest.  Driving without the head restraints in seat, allow it to dry thoroughly before Doing so could damage the arm rest. place can cause you and your passengers attempting to use the heater.
Page 29 Head restraints Adjustment of the head To remove To install restraint height Press the lock knob (A) in the direction First check that the head restraint is facing in shown by the arrows. Then pull the head the right direction as shown in the previous To reduce the risk of injury in an accident, restraint up and out of the seatback.
Page 30: Extending A Luggage Compartment
Extending a luggage compartment WARNING Extending a luggage com- partment  The front passenger seat is equipped with weight sensors. Depending on the weight N00405500105 detected, the front passenger airbag is dis- abled or enabled. When folding the rear WARNING seats forward for increased cargo capac- ...
Page 31 Extending a luggage compartment Push the rear seat release button (A) to fold 3. Make sure the seatback is locked securely NOTE the seatback forward. in place and the seat belt is passed through  When the seatback of a front seat is reclined, The rear outboard seat belt can be separated the seat belt guide (B).
Page 32: Seat Belts
Seat belts 4. If the center seat belt is stored in the rear 5. After making sure that the seat belt is not senger in the event of an accident. Always trim, pull the seat belt out and pass it twisted, insert the small latch plate (E) use the provided seat belts.
Page 33 Mitsubishi Motors as possible while maintaining a position remains seated all the way back and dealer to determine whether replacement...
Page 34 Seat belts 4. Pull the seat belt out slowly while holding 5. The lap part of the belt must always be WARNING the latch plate. Push the latch plate into worn low and snug across the hips. Pull  To reduce the risk of serious injury or the buckle until you hear a “click”.
Page 35 Seat belts WARNING WARNING To attach  Be sure the lap belt portion fits snugly and  Never detach the rear center seat belt 1. Pull the seat belt out slowly and pass it is worn as low as possible across the hips, except when the driver’s side rear seat through the seat belt guide (A).
Page 36 Seat belts 2. After making sure that the seat belt is not 2. Pass the seat belt through the seat belt Driver’s seat belt twisted, insert the small latch plate (B) guide (A) and retract it completely toward reminder/warning light and into the detachable anchor (C) aligning the rear trim.
Page 37 Seat belts If you then drive with the seat belt unfastened Front passenger seat belt warn- Adjustable seat belt shoulder for longer than a minute from when the igni- ing light anchor (front seats) tion switch or the engine switch is operated, the warning light will come on and blink N00418300194 N00406300344...
Page 38: Seat Belt Use During Pregnancy
Seat belt use during pregnancy WARNING Pre-tensioner system Seat belt use during preg- nancy  Make sure the anchor is securely locked in position after adjusting it. The driver and front passenger seat belts are N00406800134 equipped with a seat belt pre-tensioner sys- Seat belts work for everyone, including preg- Seat belt extender tem.
Page 39: Child Restraint Systems
Standard 213 (FMVSS 213) or Motor Vehicle belt pre-tensioner system inspected by an “START” position. Restraint Systems and Booster Seats Safety authorized Mitsubishi Motors dealer. [Vehicles equipped with the F.A.S.T.-key] Regulations (RSSR). Look for the manufac- The operation mode is in ON.
Page 40 Child restraint systems The child restraint system should be appropri-  Children who weigh more than 40 pounds WARNING ate for your child’s weight and height, and (18 kg) or who are more than 40 inches  Never hold an infant or child in your arms should properly fit your vehicle’s seat.
Page 41 Child restraint systems WARNING WARNING WARNING  Your vehicle is also equipped with a front  FRONT-FACING CHILD RESTRAINT  When installing a child restraint system, passenger airbag. SYSTEMS should be used in the rear seat follow the instructions provided by the Never REAR-FACING CHILD...
Page 42 Child restraint systems NOTE Installing a child restraint sys- Tether anchor locations tem using the LATCH (Lower  Before purchasing a child restraint system, N00418901214 Your vehicle has 3 attachment points on the try installing it in the rear seat to make sure Anchors and Tethers for chil- backside of the rear seats.
Page 43 Child restraint systems 2. Open a small gap between the seat cush- 3. Push the anchor connectors (D) on the Examples of child restraint sys- ion (A) and the seatback (B) with your child restraint system into the lower tems compatible with the LATCH hand to locate the lower anchors (C).
Page 44 Child restraint systems 5. Latch the tether strap hook (E) of the child WARNING Installing a child restraint sys- restraint system to the tether anchor bar tem using the seat belt (with  If there is any foreign material in or (F) and tighten the tether strap so it is around the lower anchors, remove it emergency/automatic locking...
Page 45 Child restraint systems 2. Route the seat belt through the child 3. To activate the ALR child restraint instal- WARNING restraint system’s according to the instruc- lation function, slowly pull the shoulder  When you install a child restraint system tions provided by the child restraint sys- part of the belt all the way out of the using the seat belt, always make sure the...
Page 46 Child restraint systems 5. After confirming that the belt is locked, 7. Latch the tether strap hook (A) of the 9. To remove a child restraint system from grab the shoulder part of the belt near the child restraint system to the tether anchor the vehicle and deactivate the ALR mode, remove the child from the restraint.
Page 47: Maintenance And Inspection Of Seat Belts
The SRS side airbags and the curtain airbags Mitsubishi Motors dealer. Failure to have are also designed to supplement the seat belts. an authorized Mitsubishi Motors dealer Maintenance and inspection The SRS side airbags provide the driver and...
Page 48 Supplemental Restraint System (SRS) - airbag side windows in both side impact and roll- WARNING WARNING over type accidents. • Seat belts reduce the risk of injury in • To reduce the risk to the front passenger rear impact collisions, and in lower- of serious injury or death from a deploy- The SRS airbags are NOT a substitute for use speed frontal collisions because the air-...
Page 49 Supplemental Restraint System (SRS) - airbag WARNING WARNING  Infants and small children should never  NEVER put REAR-FACING CHILD ride unrestrained, or lean against the RESTRAINT SYSTEMS or INFANT instrument panel. They should never ride RESTRAINT SYSTEMS in the front pas- held in your arms or on your lap.
Page 50 Supplemental Restraint System (SRS) - airbag When the impact sensors detect a sufficient How the Supplemental front or side impact to deploy the airbag(s), Restraint System works the appropriate airbag(s) will be deployed. N00407800450 When the airbag control unit detects rollover The SRS includes the following components: of the vehicle, curtain airbags will be...
Page 51 SRS sensors inspected by access to the vehicle or the EDR. an authorized Mitsubishi Motors dealer as and, soon as possible.  How fast the vehicle was traveling.
Page 52 SRS sensors inspected by you should have your vehicle inspected by • Do not place anything between the seat an authorized Mitsubishi Motors dealer as an authorized Mitsubishi Motors dealer as and the floor console. soon as possible.
Page 53  If any of the following conditions occur, you should have the airbag system in your vehicle inspected authorized Mitsubishi Motors dealer as soon as possi- ble: • The passenger’s airbag off indicator Warning display type 2 comes on when an adult is sitting on the front passenger seat.
Page 54 Front passenger risk of serious injury or death in certain collisions. If either of the above conditions occurs, immediately have your vehicle checked by an authorized Mitsubishi Driver’s knee airbag system Motors dealer. N00404500010 The driver’s knee airbag is located under the Driver’s and passenger’s front...
Page 55 Supplemental Restraint System (SRS) - airbag Deployment of front airbags N00408000592 The front airbags and driver’s knee airbag ARE DESIGNED TO DEPLOY when … Head-on collision with a solid wall at speeds of approx. Moderate to severe frontal impact within the shaded 15 mph (25 km/h) or higher area between the arrows The front airbags and driver’s knee airbag are...
Page 56 Supplemental Restraint System (SRS) - airbag they cannot provide protection to the occu- The front airbags and driver’s Collision with a utility pole, tree or other nar- pants. knee airbag MAY NOT DEPLOY row object Typical situations are shown in the illustra- when …...
Page 57 Supplemental Restraint System (SRS) - airbag The front airbags and driver’s Collision with an elevated median/island or curb knee airbag MAY DEPLOY when … The front airbags and driver’s knee airbag may deploy if the underside of the vehicle suffers a moderate to severe impact (under- Vehicle travels over a deep hole/pothole carriage impact).
Page 58 Mitsubishi Motors dealer. I n f o r ma t i o n P r o v i d e d b y : Seat and restraint systems...
Page 59 Supplemental Restraint System (SRS) - airbag WARNING WARNING WARNING  Side airbags and curtain airbags can  Do not place any objects around the area  Do not put a hanger or any heavy or cause serious injury or death to anyone where the side airbags deploy.
Page 60 The typical situation is shown in the illustra- if the deformation of the body seems to be Mitsubishi Motors dealer. There is a risk tion. large, because the vehicle’s body structure is of a serious injury or death. Improper...
Page 61 Supplemental Restraint System (SRS) - airbag Side impact in an area away from the passenger Head-on collision Oblique side impact compartment Rear end collision to your vehicle Motorcycle or other similar small vehicle Vehicle rolls onto its side or roof (Side airbag collision with the side of vehicle only) Pitch end over end...
Page 62 [For vehicles sold in Puerto Rico] Mitsubishi Motors dealer so that the SRS can adversely affect SRS performance and To contact Mitsubishi Motor Sales of be made safe for disposal.
Page 63 Supplemental Restraint System (SRS) - airbag [For vehicles sold in Guam] Warning label To contact Triple J Enterprises Inc. N00408600354 call (671) 649-3673 or write to: Occupant restraint warning labels for the SRS Triple J Enterprises, Inc. are located in the vehicle as shown in the P.O.
Page 64 Features and controls Break-in recommendations ..............5-3 Brake assist system ................5-64 Keys ....................5-3 Anti-lock braking system ..............5-65 Electronic immobilizer (Anti-theft starting system) ......5-4 Electric power steering system (EPS) ...........5-67 Keyless entry system (if so equipped) ..........5-7 Active stability control (ASC) ............5-68 Free-hand Advanced Security Transmitter (F.A.S.T.-key) Cruise control (if so equipped) ............5-71 Tire pressure monitoring system ...........5-75...
Page 65 Features and controls Storage spaces ................5-165 Cup holders ................. 5-167 Bottle holders ................5-168 Cargo area cover (if so equipped) ..........5-168 Assist grips .................. 5-169 Coat hook ..................5-169 Luggage hooks ................5-170 I n f o r ma t i o n P r o v i d e d b y :...
Page 66: Break-In Recommendations
Break-in recommendations Break-in recommendations Keys N00508700330 N00508800562 Advanced automobile manufacturing tech- Type 1 niques permit you to operate your new vehi- cle without requiring a long break-in period of low-speed driving. Two keys are provided. The keys fit all locks. However, you can add to the future perfor- Keep one in a safe place as a spare key.
Page 67: Electronic Immobilizer (Anti-Theft Starting System)
N00509101859 rized Mitsubishi Motors dealer. [For vehicles equipped with the Free-hand If you notify an authorized Mitsubishi Advanced Security Transmitter (F.A.S.T.- Motors dealer of the key number, they can key)] make a new key. The key number is stamped For information on operations for vehicles on the key number plate.
Page 68 Electronic immobilizer (Anti-theft starting system) Take your vehicle and all remaining keys to NOTE NOTE your authorized Mitsubishi Motors dealer to • When the key grip contacts metal of  Electronic immobilizer is not compatible have your ID code changed.
Page 69 (specially cut for procedure ing. When registration of the ID code is your vehicle at your Mitsubishi Motors • the immobilizer display does not come on complete, the immobilizer display will within 30 seconds after step 4.
Page 70: Keyless Entry System (If So Equipped)
Keyless entry system (if so equipped) It can also help you signal for attention by General information To unlock setting off the panic alarm. N00562301111 Your electronic immobilizer operates on a Press the UNLOCK button (2) to unlock the radio frequency subject to Federal Communi- driver’s door only.
Page 71 Keyless entry system (if so equipped) Horn deactivation/reactivation Turn signal lights deactiva- Setting the door and liftgate tion/reactivation unlock function The answerback function can be set in the N00543601128 following three ways. The answerback function can be turned ON The door and liftgate unlock function can be Each time the answerback function is set, a or OFF separately.
Page 72 Registering the ID code can be done by your- 1 second. 3. Within 10 seconds of pressing the LOCK self or by your authorized Mitsubishi Motors 2. The headlights will blink on and off and button, release the LOCK button first, and dealer.
Page 73  Changes or modifications not expressly unlock the doors with the re-coded remote rized Mitsubishi Motors dealer. A maximum approved by the manufacturer for compli- control transmitters after the registration is of 8 remote control transmitters can be pro- ance could void the user’s authority to oper-...
Page 74: Free-Hand Advanced Security Transmitter (F.a.s.t.-Key) (If So Equipped)
 Be sure to perform the procedure with the nents. Mitsubishi mark facing you. Mitsubishi mark is not facing you when you + side open the remote control transmitter case, the Free-hand Advanced Secu- buttons may come out. rity Transmitter (F.A.S.T.-...
Page 75 Refer to “Free-hand Advanced Security details, contact authorized Transmitter (F.A.S.T.-key): Keyless entry Mitsubishi Motors dealer. system” on page 5-24. • Enabling only the locking and unlocking of the doors and the liftgate • Enabling only the starting of the engine The F.A.S.T.-key must be carried by the...
Page 76 Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped) when the ID codes of the vehicle and NOTE F.A.S.T.-key match. Use the emergency key in such circum- stances. Refer to “To operate without using the F.A.S.T.-key” on page 5-22.  The F.A.S.T.-key is constantly performing reception operations in its communication with the vehicle.
Page 77 Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped) Operating range for starting the NOTE Driver’s and front passenger’s door lock/unlock engine and changing the opera- switches  Even if the F.A.S.T.-key is inside the vehicle, it may not be possible to start the engine and tion mode change the operation mode if the key is too N00503300067...
Page 78  The time within which locking confirmation is possible can be adjusted. See an autho- rized Mitsubishi Motors dealer for details. NOTE Liftgate OPEN switch To unlock ...
Page 79 See an autho-  When operating the engine switch, press the rized Mitsubishi Motors dealer for details. switch all the way in. If the switch is not  In cases such as the following, the F.A.S.T.- fully pressed, the engine may not start or the key does not operate.
Page 80 For details, we recommend you to consult an one registered to the immobilizer computer.  When the battery is disconnected, the current authorized Mitsubishi Motors dealer. (Refer to “Electronic immobilizer (Anti-theft operation mode is memorized. After recon- starting system)” on page 5-23) necting the battery, the memorized mode is selected automatically.
Page 81 This setting can be changed. tion system” on page 5-18. If the warning is not cancelled, See an authorized Mitsubishi Motors dealer there is a fault in the electronic for details. Refer to “Door ajar prevention immobilizer (Anti-theft start- ...
Page 82 Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped) and someone tries to lock the vehicle by  The starter motor will be turning for up to Operation mode OFF reminder pressing the driver’s or front passenger’s door approximately 15 seconds if the engine system lock/unlock switch, or the liftgate LOCK switch is released at once.
Page 83 Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped) 4. Press and hold the clutch pedal all the way WARNING When the engine is hard to start down (manual transaxle).  Never run the engine in a closed or poorly 5. On vehicles equipped with manual trans- After several attempts, you may experience ventilated area any longer than is needed axle, place the gearshift lever in the “N”...
Page 84 If the engine still will not start, con- downhill) position. engine is stopped while driving, the brake tact your local Mitsubishi Motors dealer On vehicles equipped with continuously servomechanism will cease to function and or a repair facility of your choice for braking efficiency will deteriorate.
Page 85 Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped) If the operation mode is in OFF and the driver’s door is opened with the F.A.S.T.-key in the key slot, a warning is issued with the warning display and the buzzer buzzing for approximately 3 seconds to remind you to remove the key.
Page 86 (Except for vehicles sold in To prevent vehicle theft, take your vehicle and the remaining F.A.S.T.-keys to an autho- Canada) 1- Insert or remove the emergency key rized Mitsubishi Motors dealer to have the ID 2- Lock N00561201184 codes reprogrammed. 3- Unlock You can program new F.A.S.T.-keys to the...
Page 87 Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped) 3. Insert the new F.A.S.T.-key into the key 7. Within 10 seconds of pressing the LOCK 8. If you wish to register another F.A.S.T.- slot. button in step 6, release the LOCK button key, repeat the process from step 1 after the operation mode is put in OFF.
Page 88 Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped) The horn will not sound. To unlock chime: The horn will sound. Press the UNLOCK button (2) to unlock the chimes: driver’s door only. Four The horn will sound if the LOCK To unlock all doors and the liftgate, press the chimes: button is pressed twice within 1 sec-...
Page 89 Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped) 3. Press and hold the UNLOCK button (2) Setting the door and liftgate Using the panic alarm for 4 to 10 seconds and then press and unlock function N00544701070 hold the LOCK button (1) during this If you are near your vehicle and feel threat- N00544601109 time.
Page 90 5-23. Mitsubishi mark facing you. electricity from your body by touching a Mitsubishi mark is not facing you when you metal grounded object. open the case, the transmitter may come out. General information N00562001088 3. Remove the old battery.
Page 91: Door Locks
2- Lock  Never leave a child alone in the vehicle. In  An authorized Mitsubishi Motors dealer can addition to the risk of heat stroke, chil- 3- Unlock replace the battery for you if you prefer.
Page 92 Door locks 2. Be sure the keys are not inside the vehi- NOTE cle. Close the door.  When locking or unlocking with the key, only the driver’s door will be locked or unlocked. To lock or unlock all doors and the liftgate, use the power door lock switches, the key- less entry system or the F.A.S.T-key opera- tion.
Page 93: Power Door Locks
Power door locks If the ignition switch is turned off and the ON buzzer will sound intermittently to To lock and unlock the doors driver’s door is opened with the key in the remind you to put the operation mode in OFF. and liftgate ignition switch, the key reminder buzzer will The warning display will be displayed on the...
Page 94: Child Safety Locks For Rear Door
To acti- side door handle. vate or deactivate these functions, please When the lever is in the release position (2), contact your authorized Mitsubishi Motors the child safety lock is released and the rear dealer. Child safety locks for rear...
Page 95: Liftgate
Liftgate To open To close Liftgate N00510101253 After unlocking, raise the liftgate. Pull the liftgate grip (A) downward as illus- WARNING trated and release it before the liftgate closes  It is dangerous to drive with the liftgate completely. Gently slam the liftgate from the open since carbon monoxide (CO) gas can outside so that it is completely closed.
Page 96: Inside Liftgate Release
Inside liftgate release 2. Move the lever (B) to open the liftgate. NOTE  Gas struts (B) are installed in the locations illustrated in order to support the liftgate. Please observe the following in order to pre- vent damage or faulty operation: •...
Page 97 Theft-alarm system 3. Lock all doors and the liftgate by using 4. The system has entered the armed stage CAUTION the keyless entry system or the F.A.S.T.- after about 20 seconds, when the theft-  Do not modify or add parts to the theft-alarm key operation.
Page 98 Theft-alarm system Type 2 NOTE Horn sounds! Headlights blink on and off!  The theft-alarm system can be activated when people are riding inside the vehicle or when the windows are open. To prevent acci- dental activation of the alarm, do not set the system to the system armed mode while peo- ple are riding in the vehicle.
Page 99: Power Window Control
See an authorized Mitsubishi battery. Use the window switches only while Motors dealer for details. the engine is running.  Once the system has been disarmed, it can- not be rearmed except by repeating the arm- ing procedure.
Page 100 Power window control WARNING Sub switch  Never leave the vehicle without carrying N00548800098 the key.  Never leave children or unreliable adults unattended inside the vehicle. Main switch N00548700097 The main switch located on the driver’s door can be used to operate all the windows. 1- Driver’s door window switch A window can be opened or closed by operat- 2- Front passenger door window switch...
Page 101 Power window control stopped. However, once the driver’s door or WARNING CAUTION the front passenger’s door is opened, the  Before driving with a child in the vehicle,  The safety mechanism is deactivated while power windows cannot be operated. be sure to lock the window switch to make the switch is pulled up.
Page 102: Sunshade (If So Equipped)
Press and hold the switch (1), the sunshade  Before operating the sunshade, make sure authorized Mitsubishi Motors dealer. automatically opens. Release the switch once that nothing can be trapped (head, hands,  Operating the sunshade repeatedly with the the sunshade starts moving automatically.
Page 103: Parking Brake
Parking brake To stop the moving sunshade, press the uphill) or “R” (Reverse) (on a downhill) posi- To deactivate switch (1), (2) or (3). tion for vehicles equipped with a manual transaxle, set the selector lever to “P” (PARK) position for vehicles equipped with a Safety mechanism continuously variable transmission (CVT).
Page 104: Steering Wheel Height And Reach Adjustment
Steering wheel height and reach adjustment CAUTION WARNING Steering wheel height and reach adjustment  Before driving, be sure that the parking  When releasing the lever (moving it to the brake is fully released and brake warning position (B)), be sure to hold the steering N00511500228 light is off.
Page 105 Inside rearview mirror To reduce the glare Type 1 Type 1 The day/night knob (A) at the bottom of the mirror can be used to adjust the mirror to Type 2 reduce the glare from the headlights of vehi- cles behind you during night driving. To adjust the mirror position Adjust the inside mirror to maximize the It is possible to move the mirror up/down and...
Page 106: Outside Rearview Mirrors
Outside rearview mirrors WARNING To adjust the mirror position  Do not attempt to adjust the outside rear- N00549100131 The outside rearview mirrors can be adjusted view mirrors while driving. This can be dangerous. when the ignition switch or the operation Be sure to adjust the mirrors before driv- mode is in ON or ACC.
Page 107: Ignition Switch
Ignition switch The indicator light (A) will illuminate while [Except for vehicles equipped with the NOTE the defogger is on. Free-hand Advanced Security Transmit-  After adjusting, return the lever to the “•” The heater will be turned off automatically in ter (F.A.S.T.-key)] (OFF) position (C).
Page 108: Starting The Engine
For details, we recommend you to consult an NOTE  Do not leave the key in the “ON” position for authorized MITSUBISHI MOTORS dealer. a long time when the engine is not running,  Your vehicle is equipped with an electronic doing so will cause the battery to be dis- immobilizer.
Page 109 Starting the engine 6. On vehicles equipped with manual trans- Tips for starting CAUTION axle, place the gearshift lever in the “N”  Do not push-start the vehicle. (Neutral) position.  Do not operate the starter motor continu-  Do not run the engine at high rpms or drive On vehicles equipped with continuously ously for longer than 15 seconds as this at high speeds until the engine has had a...
Page 110: Manual Transaxle (If So Equipped)
Press the clutch pedal all the way engine still will not start, contact your down while shifting gears. local Mitsubishi Motors dealer or a repair facility of your choice for assistance. Startability of automatic transaxle vehicle and CVT vehicle with ambient temperature of -22 °F (-30...
Page 111 Manual transaxle (if so equipped) NOTE NOTE Upshifting  During cold weather, shifting may be diffi-  To shift into reverse from 5th gear, move the N00512901154 cult until the transaxle lubricant has warmed gearshift lever to the “N” (Neutral) position, For the best fuel economy and performance in up.
Page 112: Continuously Variable Transmission (Cvt) (If So Equipped)
Continuously variable transmission (CVT) (if so equipped) mode” on page 5-53. Downshifting Maximum possible driving speed N00513000096 DRIVING UPHILL It is recommended that you downshift to a Shift Maximum possible driving lower gear when needed to maintain the points speed transmission prevents unnecessary...
Page 113 “N” (NEUTRAL) Immediately have your vehicle checked by an position while pressing the accelerator authorized Mitsubishi Motors dealer or a pedal. This will cause the vehicle to NOTE “jump” forward or backward. repair facility of your choice.
Page 114 Continuously variable transmission (CVT) (if so equipped) If you need to move the vehicle, shift the 5. Insert a screwdriver in the shift-lock Type 1 Type 2 selector lever as follows. release hole (B). Shift the selector lever to the “N” (NEUTRAL) position while 1.
Page 115 1. Depress the brake pedal with your right inspected by an authorized Mitsubishi in the multi-information display while you foot and place the selector lever in the Motors dealer or a repair facility of your are driving, there could be a malfunction in choice.
Page 116 Continuously variable transmission (CVT) (if so equipped) “D” (DRIVE) operation, push the selector “R” REVERSE WARNING lever back into the main gate (B).  To prevent the vehicle from rolling when In sports mode, rapid shifting is possible sim- stopped on a slope, the engine should be Move the lever to this position only after the ply by operating the selector lever or spor- started in the “P”...
Page 117 Continuously variable transmission (CVT) (if so equipped) CAUTION NOTE  In sports mode, the driver must execute  To maintain good running performance, the SHIFT upward shifts in accordance with prevailing transmission may refuse to perform an SHIFT road conditions, taking care to keep the upshift when the selector lever or sportronic DOWN engine speed below the red zone.
Page 118 Continuously variable transmission (CVT) (if so equipped) CAUTION NOTE Type 1 Type 2  Operating the accelerator pedal while the  In sports mode, downshifts do not take place other foot is resting on the brake pedal will when the accelerator is depressed all the way affect braking efficiency and may cause pre- to the floor.
Page 119: Electronically Controlled 4Wd System (If So Equipped)
Have your vehicle checked at an ing skills. freeways. authorized Mitsubishi Motors dealer or a Carefully read the “4-wheel drive operation” Driving in front- repair facility of your choice as soon as possi- section on page 5-58 and take care to drive wheel drive.
Page 120 Electronically controlled 4WD system (if so equipped) Type 2 Display Drive mode Type 1 Type 2 LOCK Normally the indicator illuminates when the ignition switch is turned to the “ON” position CAUTION or the operation mode is put in ON, and then ...
Page 121: 4-Wheel Drive Operation
Have an inspection made by you to occasionally travel on unpaved roads, mode-selector. an authorized Mitsubishi Motors dealer or a to campgrounds, picnic sites, and similar The warning display is also displayed in the repair facility of your choice as soon as pos- locations.
Page 122  Avoid sudden braking, sudden acceleration  Mitsubishi Motors is not responsible to the and sharp turning. Skidding occurs and con- operator for any damage or injury caused or trol of the vehicle could be lost.
Page 123 Mitsubishi Motors Refer to “Engine overheating” on page 8-4. Climbing/descending sharp dealer or a repair facility of your choice and take the necessary measures to prepare, •...
Page 124: Inspection And Maintenance Following Rough Road Operation
Mitsubishi Motors dealer or a repair facil- vehicle when operating in 4-wheel drive is greatly affected by the condition of the tires. ity of your choice as soon as possible to have the brakes checked.
Page 125: Service Brake
Service brake Towing Jacking up a 4-wheel drive CAUTION vehicle  It is important not to drive the vehicle with your foot resting on the brake pedal when braking is not required. This practice can WARNING result in very high brake temperatures, pre- mature lining wear, and possible damage to ...
Page 126: Hill Start Assist
 Do not overly rely on the hill start assist to take your vehicle to an authorized To operate prevent backwards movement of the vehicle. Mitsubishi Motors dealer or a repair facil- Under certain circumstances, even when hill N00562700059 ity of your choice immediately.
Page 127: Brake Assist System
(The hill start assist will not be activated immediately, but the vehicle should be while the engine is starting or immediately inspected by an authorized Mitsubishi after the engine is started.) Motors dealer or a repair facility of your Warning display type 1 •...
Page 128: Anti-Lock Braking System
Anti-lock braking system NOTE Driving hints CAUTION  Once the brake assist system is operational,  The anti-lock braking system cannot prevent  When using the anti-lock brakes (sudden it maintains great braking force even if the accidents. It is your responsibility to take braking), steering is slightly different brake pedal is lightly released.
Page 129 If this happens, take your vehicle MITSUBISHI MOTORS dealer or repair to an authorized Mitsubishi Motors dealer or facility of your choice as soon as possible. a repair facility of your choice. I n f o r ma t i o n P r o v i d e d b y :...
Page 130: Electric Power Steering System (Eps)
Avoid hard braking and high-speed driving. effort to steer. If this happens, have your vehi- Stop the vehicle in a safe place and contact an cle inspected at an authorized Mitsubishi authorized MITSUBISHI MOTORS dealer or Motors dealer or a repair facility of your repair facility of your choice.
Page 131: Active Stability Control (Asc)
 When the anti-lock braking system warning ing can lead to accidents. It is the driver’s by an authorized Mitsubishi Motors dealer or light is illuminated, the ASC is not active. responsibillty to drive carefully, This means...
Page 132 Active stability control (ASC) start moving from a stopped condition. It also When the ASC is deactivated, the dis- NOTE provides sufficient driving force and steering play/indicator will turn on. To reactivate the  When moving out of mud, sand or fresh performance as the vehicle turns while press- ASC, momentarily press the “ASC OFF”...
Page 133 - ASC indicator should have your vehicle inspected by an function and normal brake operation will not authorized Mitsubishi Motors dealer or a be affected. Park your vehicle in a safe place. - ASC OFF display/ASC OFF indicator repair facility of your choice as soon as pos- When the temperature in the braking system sible.
Page 134: Cruise Control (If So Equipped)
Cruise control (if so equipped) Towing CAUTION Cruise control switches  Do not use cruise control when driving con- N00546300031 ditions will not allow you to stay at the same CAUTION speed, such as in heavy traffic or on roads that are winding, icy, snow-covered, wet, ...
Page 135 Cruise control (if so equipped) 2. Accelerate or decelerate to your desired To activate NOTE speed, then push down and release the  If the cruise control is on when the following N00518401409 SET - switch (B) when the “CRUISE” 1.
Page 136 Cruise control (if so equipped) When you reach your desired speed, release the switch. Your new cruising speed is now set. To slow down your speed in small amounts, push down the SET - switch for less than To decrease the set speed about 1 second and release it.
Page 137 Cruise control (if so equipped) To deactivate N00518801591 The set speed driving can be deactivated as follows:  Press the CRUISE CONTROL ON/OFF switch (A). (Cruise control will be turned off.)  Press the CANCEL switch (D).  Depress the brake pedal. To temporarily decrease the speed To temporarily increase or decrease the speed...
Page 138: Tire Pressure Monitoring System
Tire pressure monitoring system  When the active stability control (ASC)  [Except for vehicles equipped with the To resume the set speed starts operating. F.A.S.T.-key] N00518901329 Refer to “Active stability control (ASC)” Turn the ignition switch to the “OFF” or If the set speed driving is deactivated by any on page 5-68.
Page 139 See an authorized Mitsubishi Motors mode is in ON. dealer as soon as possible to replace or Refer to “If the warning light / display illumi- repair the original tire.
Page 140 Have the system overheat and can lead to tire failure. inspected by an authorized Mitsubishi Under-inflation also reduces fuel efficiency Motors dealer. In such situations, a malfunctioning of the...
Page 141 Mitsubishi minates while driving driving. Motors dealer. If the tire repair is not done by an authorized Mitsubishi Motors dealer, it is N00532801524 2. If the tire pressure monitoring system 1. If the tire pressure monitoring system not covered by your warranty.
Page 142: Rear-View Camera (If So Equipped)
CAUTION wheels are being used. rized Mitsubishi Motors dealer, it is not cov-  Changes or modifications not expressly  Wheels that are not fitted with tire infla- ered by your warranty.
Page 143 Rear-view camera (if so equipped) WARNING CAUTION  The view on the screen is limited, and • Do not splash hot water directly on the lens. objects outside the view, such as under the • Do not spray the camera and its surround- bumper or around either corner of the ings with high-pressure water.
Page 144: Instrument Cluster
NOTE • When there is an upward slope at the back.  The reference lines for distance and vehicle  On vehicles equipped with Mitsubishi Multi- (Case 2) width are intended to indicate the distance to Communication System, it is possible to a flat object such as a level, flat road surface.
Page 145 Instrument cluster 3- Speedometer  P.5-82 Tachometer Rheostat meter illumination 4- Rheostat meter illumination button  button N00519200289 P.5-82 The tachometer shows engine revolutions per N00554901235 minute. This allows the driver to determine Each time you press this button, there is a Speedometer the most efficient selector position and engine sound and the brightness of the instruments...
Page 146: Multi-Information Display
Multi-information display 2- Rheostat illumination button 1- Brightness display Multi-information display N00555000265 The multi-information display displays warnings, the odometer, trip odometer, service reminder, engine coolant temperature, fuel remaining, out- side temperature, selector lever position, all-wheel drive operation status, average and momentary fuel consumption, driving range, average speed, instrument brightness, etc.
Page 147 Multi-information display With ignition switch or opera- With ignition switch or operation mode is in With ignition switch or operation mode is in tion mode is in OFF ON (CVT) ON (Manual transaxle) Type 1 Type 2 Type 1 Type 2 Type 1 Type 2 10- Fuel remaining display screen ...
Page 148 Multi-information display momentary fuel consumption, driving range, This mark is also displayed if there is another NOTE and average speed. warning other than the one displayed. When  The display screen is different depending on It is also possible to change elements such as the cause of the warning display is elimi- whether the ignition switch or the operation the language and units used on the multi-...
Page 149 Multi-information display seconds or more. Only the currently dis- Odometer/Trip odometer Type 1 played value will be reset. N00555400113 Each time you lightly press the multi-infor- Example mation meter switch, the display screen When there is no If trip odometer is displayed, only trip warning display switches.
Page 150 Multi-information display to the appropriate page and take the necessary screen display from before the warning and NOTE measures. warning (A) is displayed.  If there is no warning display, the switching When the cause of the warning display is ...
Page 151 Multi-information display switch a few times, the warning display Information screen (With the System check screen screen you switched from is redisplayed. ignition switch is turned from Refer to “Information screen (With ignition When the ignition switch is turned to the the “OFF”...
Page 152 Multi-information display Service reminder Warning display screen “Active stability control (ASC) (With ignition switch or opera- OFF” display screen (if so When the time for periodic inspection arrives, tion mode in ON) equipped) the warning display is displayed for a few N00555200182 N00556100117 seconds after the screen that is initially dis-...
Page 153 Multi-information display NOTE 1- Odometer (Type1)/Trip odometer Type 1 2- Odometer (Type1)/Trip odometer  When there is information to be announced, 3- Service reminder such as a system fault, the tone sounds and the screen display is switched. Engine coolant temperature display Refer to “Interrupt display screen (With igni- (Type 1) When there is no warning display...
Page 154 Multi-information display  When the following operation is per- CAUTION NOTE formed, the mode setting changes auto-  The display setting can be changed to the  If the engine is overheating, “ ” will blink. matically from manual to auto. preferred units (miles or km).
Page 155 Multi-information display  When the engine switch or the operation  When the following operation is per- NOTE mode is in the following conditions, the formed, the mode setting changes auto-  Disconnecting the battery cable will erase matically from manual to auto. average speed display will automatically from memory the manual reset mode or auto reset.
Page 156 Multi-information display  When the engine switch or the operation NOTE NOTE mode is in the following conditions, the  Disconnecting the battery cable will erase  The display setting can be changed to the average fuel consumption display will from memory the manual reset mode or auto preferred units...
Page 157 Multi-information display information screen is switched to the warning switch a few times, the warning display Type 1 display screen. screen you switched from is redisplayed. Refer to the warning list and take the neces- sary measures. Refer to “Warning display list Other interrupt displays (With ignition switch or operation mode in ON)”...
Page 158 Multi-information display NOTE Fuel remaining warning display Type 1 Type 2  The display setting can be changed to the preferred units (°F or °C). When the fuel level runs low, the information Refer to “Changing the function settings screen switches to the interrupt display of the (With ignition switch or operation mode in fuel remaining warning display and the mark ON)”...
Page 159 NOTE tion is due. Contact an authorized tion switch or the operation mode is in OFF. Mitsubishi Motors dealer or a repair facil-  The service reminder time can be modified When the display is reset, the time until the...
Page 160 Type 1 play is reset and the time until the next periodic inspection is displayed.  If you accidentally reset the display, consult an authorized Mitsubishi Motors dealer for assistance. Type 2 Type 2 Door ajar warning display...
Page 161 Multi-information display If any of the doors or the liftgate is not com- 2. When you lightly press the multi-informa- 3. Press and hold the multi-information pletely closed, this displays the open door or tion meter switch, the information screen meter switch (for about 2 seconds or liftgate.
Page 162 Multi-information display 4. Select the item to change on the menu 3. Press and hold the multi-information Changing the reset mode for aver- screen and change to the desired setting. meter switch (for about 2 seconds or age fuel consumption and average For further details on the operation meth- more) to switch in sequence from A or 1 speed...
Page 163 Multi-information display 3. Press and hold the multi-information Changing the fuel consumption Auto reset mode meter switch (for about 2 seconds or display unit more) to display “AVG UNIT” (fuel con-  When the average fuel consumption and N00557100143 sumption display unit setting). average speed are being displayed, if you The fuel consumption display unit can be 4.
Page 164 Multi-information display 1. Press and hold the multi-information 3. Press and hold the multi-information NOTE meter switch (for about 2 seconds or meter switch (for about 2 seconds or  The display units for the driving range, the more) to change in sequence from °F  more) to switch from the setting mode average fuel consumption, the average speed °C ...
Page 165 Multi-information display 2. Lightly press the multi-information meter 2. Lightly press the multi-information meter NOTE switch to select “LANGUAGE” (lan- switch to select “ ” (operation sound  If “---” is selected in the language setting, a guage setting). setting). warning message is not displayed when there is a warning display or interrupt display.
Page 166 Multi-information display 2. Lightly press the multi-information meter 4. Lightly press the multi-information meter NOTE switch to select “ALARM” (rest time set- switch to select the time until the display  The operation sound setting only deactivates ting). appears. the operation sound of the multi-information 5.
Page 167 Multi-information display 2. Lightly press the multi-information meter 1. Press and hold the multi-information Returning to the factory settings meter switch for about 2 seconds or more switch to select . (changing the turn N00557600151 to switch from the setting mode screen to signal sound) All of the function settings can be returned to the menu screen.
Page 168: Indicator Light, Warning Light, And Information Screen Display List
Indicator light, warning light, and information screen display list 3. Press and hold the multi-information NOTE NOTE meter switch (for about 5 seconds or • Average fuel consumption and average • Operation sounds: ON (Operation sound more), the buzzer sounds and all of the speed reset mode: A (Auto reset) function settings are returned to the fac- •...
Page 169 Indicator light, warning light, and information screen display list 8- Brake warning light  P.5-118 14- Active stability control (ASC) OFF 1- Position indicator  P.5-118 indicator (if so equipped)  P.5-69 9- Cruise control indicator 2- High beam indicator  P.5-118 equipped) ...
Page 170 Indicator light, warning light, and information screen display list NOTE If the warning display has occurred a number of times, take your vehicle to an authorized Mitsubishi Motors dealer or a repair facility of your choice and have the system checked.
Page 171 Refer to “Free-hand Advanced Security Trans- mitter (F.A.S.T.-key)” on page 5-11. —  There is a fault in the electronic immobi-  Contact an authorized Mitsubishi Motors lizer. (Anti-theft starting system). dealer or a repair facility of your choice to —...
Page 172  Park your vehicle in a safe place as soon as possible and contact an authorized — Mitsubishi Motors dealer or a repair facil- ity of your choice to have the system checked. Warning display list (With ignition switch or operation mode is in ON)
Page 173 Indicator light, warning light, and information screen display list Screen type 1 Screen type 2 Cause Do this (Reference)  There is a fault in the F.A.S.T.-key. Refer to “Free-hand Advanced Security Trans- mitter (F.A.S.T.-key)” on page 5-11. —  Immobilizer is registered. Refer to “Customer key programming (Except for vehicles sold in Canada)”...
Page 174  Park the vehicle in a safe place and inspect  There is a fault in the brake system.  If the light still illuminates after the inspec- tion, contact an authorized Mitsubishi Motors dealer or a repair facility of your choice for assistance.
Page 175  There is a fault in the electrical system.  Park your vehicle in a safe place as soon as possible and contact an authorized — Mitsubishi Motors dealer or a repair facil- ity of your choice to have the system checked.  The engine is overheated.
Page 176  Park your vehicle in a safe place as soon as system. possible and contact an authorized Mitsubishi Motors dealer or a repair facil- ity of your choice to have the system checked. Refer to “Oil pressure warning display” on page 5-121.
Page 177 5-68.  There is a fault in the Hill start assist.  Have the vehicle checked at an authorized Mitsubishi Motors dealer or a repair facil- ity of your choice. Refer to “Hill start assist” on page 5-63.
Page 178 Indicator light, warning light, and information screen display list Screen type 1 Screen type 2 Cause Do this (Reference)  The fuel is running low.  Refuel as soon as possible. Refer to “Fuel remaining display screen” on page 5-95. ...
Page 179 Indicator light, warning light, and information screen display list The operation status of each system is displayed on the information screen. For further details, refer to the appropriate page for each system. Screen type 1 Screen type 2 System operation status Reference ...
Page 180: Indicators
This informs you that a periodic inspection is due. Screen type 1 Screen type 2 Do this Have an inspection made by an authorized Mitsubishi Motors dealer. For further details, refer to “Service reminder” on page 5-96. The rest time can be set. Screen type 1...
Page 181 ON. a safe place, and contact an authorized N00520100086 Mitsubishi Motors dealer or a repair facility When the engine is started, the light should A blue light comes on when the headlights of your choice as soon as possible.
Page 182: Information Screen Display
Mitsubishi Motors dealer or a repair facility If this indicator does not go off after several of your choice to have the system checked. seconds or lights up while driving, have the...
Page 183 If this happens, park the vehicle in a N00558600103 is applied. Type 1 safe place, and contact an authorized Mitsubishi Motors dealer or a repair facility CAUTION of your choice.  If the brake warning display, brake warning  If a vehicle is driven without releasing the...
Page 184: Combination Headlights And Dimmer Switch
This is the same as when Mitsubishi Motors dealer or a repair facility and damage may result. window glass mists up on a humid day, and of your choice to have the system checked.
Page 185 Combination headlights and dimmer switch NOTE Except for vehicles equipped with day- time running lights  Once the daytime running light come on, they do not go out until the ignition switch is OFF All lights off turned to the “OFF” or “ACC” position or the operation mode is changed to OFF or Parking, tail, front and rear side- ACC.
Page 186 “AUTO” position, manually Headlights and other lights on operate the switch. Have the system checked The daytime running lights illumi- by an authorized Mitsubishi Motors dealer or nated a repair facility of your choice. NOTE Tail, front and rear side-marker lights, license plate and instrument ...
Page 187 N00532601593 See your authorized Mitsubishi Motors  If the following operation is performed • If the operation mode is changed to any dealer for details. with the combination headlights and dim- mode other than OFF and the driver’s...
Page 188 Combination headlights and dimmer switch the light switch to the “OFF” position to stop go back to normal when you let go. While the NOTE the tone. high beam is on, you will see a blue light on  When the engine is started using the the instrument panel.
Page 189 • The welcome light function can be deacti- the operation mode in OFF, pull the turn vated. signal lever toward you. For details, consult a Mitsubishi Motors dealer. Coming home light N00547301123 This function turns on the headlights in the low beam setting for about 30 seconds after the ignition switch is turned to the “OFF”...
Page 190: Headlight Leveling Switch (If So Equipped)
• The coming home light function can be deactivated. complete. There may be times when the lever For details, consult a Mitsubishi Motors does not return to the neutral position. This dealer. usually happens when the steering wheel is turned only slightly.
Page 191: Hazard Warning Flasher Switch
If you need to leave your vehicle, the flashers Have the system inspected by your autho- will keep working after the ignition switch is rized Mitsubishi Motors dealer or a repair removed or the operation mode is put in OFF. facility of your choice.
Page 192: Wiper And Washer Switch
Wiper and washer switch NOTE Windshield wipers  If the light switch is rotated to the “OFF” or “ ” position while the front fog lights are NOTE illuminated, they will automatically turn off.  To ensure a clear rearward view, the rear They can be turned back on again by rotating window wiper will automatically perform the combination headlights and dimmer...
Page 193 For further information, please contact your ness on the windshield. If the blades are frozen to the windshield or authorized MITSUBISHI MOTORS dealer LO- Slow rear window, do not operate the wipers until or a repair facility of your choice.
Page 194  In the following cases, the rain sensor may windshield, if you touch the rain sensor. be malfunctioning. Have the vehicle checked at an authorized Mitsubishi Motors dealer or • When cleaning the outside surface of the a repair facility of your choice.
Page 195 For further information, please contact your authorized MITSUBISHI MOTORS dealer or a repair facility of your choice. Misting function Move the lever in the direction of the arrow and release, to operate the wipers once.
Page 196 When the washer fluid is sprayed, the See your authorized Mitsubishi Motors about 6 seconds. wiper will automatically operate 2 or dealer for details. For details, consult a Mitsubishi Motors 3 times.  The washer fluid reservoir is located in the dealer. engine compartment.
Page 197: Electric Rear Window Defogger Switch
Horn switch If you need the defogger for more than 20 blades. For further information, please con- minutes, press the switch again. This will add tact your authorized Mitsubishi Motors N00523801209 20 more minutes. dealer. To honk the horn, press around the “...
Page 198: Link System (If So Equipped)
ON or ACC. You have acquired a device that includes soft- or the engine switch is operated. Refer to “ACC power auto-cutout function” on page ware licensed by Mitsubishi Motors Corpora- ® Before you can use the Bluetooth 2.0 inter- 5-45.
Page 199 While the system is in voice recognition [For vehicles sold in Canada and MEXICO] mode, “Listening” will appear on the You can see to access via the MITSUBISHI audio display. MOTORS web site. Please read and agree to the “Warning about NOTE Links to the Web Sites of Other Companies”.
Page 200 Mitsubishi Multi-Communication as far as possible from the microphone.  When you press the SPEECH button (except System, will activate the voice recognition of for vehicles with Mitsubishi Multi-Commu- ® the Bluetooth 2.0 interface. nication System) or PICK-UP button (for...
Page 201 1. Press the SPEECH button (except for with a confirmation function. pleted and the system will return to the vehicles with Mitsubishi Multi-Commu- With the confirmation function activated, you main menu. nication System) or PICK-UP button (for...
Page 202 SPEECH button prompts are <off/on>” and then the sys- digit passcode. Remember this passcode. (except for vehicles with Mitsubishi Multi- tem will return to the main menu. It will be required to use this system.”...
Page 203  If you have forgotten your passcode, say uously variable transmission (CVT)), and “Cancel” to quit the voice input mode and pull the parking brake lever. Speaker enrollment function then check with an authorized Mitsubishi Motors dealer. NOTE N00564701021 ®...
Page 204 1. Press the SPEECH button (except for NOTE mand, press and release the SPEECH button. vehicles with Mitsubishi Multi-Commu-  If you press the HANG-UP button anytime  If you do not start the speaker enrollment nication System) or PICK-UP button (for...
Page 205 NOTE 2. Press the SPEECH button (except for ® with the Bluetooth 2.0 interface. vehicles with Mitsubishi Multi-Commu- ®  Some Bluetooth devices require a specific ® nication System) or PICK-UP button (for If multiple paired Bluetooth devices are pairing code.
Page 206 You 1. Press the SPEECH button (except for Depending on the connection settings of the can assign a desired name for the Blue- vehicles with Mitsubishi Multi-Commu- ® Bluetooth device, this code may have to be ®...
Page 207 1. Press the SPEECH button (except for phones will be read out in order, starting ers will be read out in order, starting with vehicles with Mitsubishi Multi-Commu- with the cellular phone that has been most the music player that has been most nication System) or PICK-UP button (for recently connected.
Page 208 1. Press the SPEECH button (except for 7. The voice guide will say “Deleted,” and 6. After the device tags of all paired Blue- vehicles with Mitsubishi Multi-Commu- then the system will end the device dele- ® nication System) or PICK-UP button (for...
Page 209 Bluetooth compatible cellular phone 1. Press the SPEECH button (except for ately say the number of the device tag you ® vehicles with Mitsubishi Multi-Commu- connected to the Bluetooth 2.0 interface. want to change. nication System) or PICK-UP button (for...
Page 210 You can make a call in the following 3 ways 1. Press the SPEECH button (except for make the call. ® vehicles with Mitsubishi Multi-Commu- using the Bluetooth 2.0 interface: When the confirmation function is on, the nication System) or PICK-UP button (for...
Page 211 Say “Add location” and you can register an 1. Press the SPEECH button (except for additional telephone number under the vehicles with Mitsubishi Multi-Commu- selected location. nication System) or PICK-UP button (for  If the name you selected has matching data...
Page 212 Bluetooth® 2.0 interface (if so equipped) “<numbers> SEND” to generate DTMF are the vehicle phonebook and the mobile Mute function tones. phonebook. N00565900010 For example, if during a call you need to sim- These phonebooks are used to register tele- At any time during a call, you can mute the ulate the pressing of a phone button as a phone numbers and make calls to desired...
Page 213 1. Press the SPEECH button (except for voice guide will say “home, work, istered, the voice guide will say “Number vehicles with Mitsubishi Multi-Commu- mobile, or other?” Say the location for saved. Would you like to add another nication System) or PICK-UP button (for which you want to register a telephone number for this entry?”...
Page 214 Bluetooth compatible cellular phone. NOTE 1. Press the SPEECH button (except for vehicles with Mitsubishi Multi-Commu-  If the entered name is already used for another phonebook entry or similar to a nication System) or PICK-UP button (for name used for another phonebook entry, that vehicles with Mitsubishi Multi-Commu- name cannot be registered.
Page 215 1. Press the SPEECH button (except for tion where the telephone number you system will ask if the name is correct. vehicles with Mitsubishi Multi-Commu- want to change or add is registered. Answer “Yes.” nication System) or PICK-UP button (for When the confirmation function is on, the Answer “No,”...
Page 216 NOTE Answer “Yes” if you want to continue vehicles with Mitsubishi Multi-Commu- with the editing based on this information. nication System) or PICK-UP button (for  You can call, edit or delete a name that is Answer “No,”...
Page 217 N00580300086 guide will say “Deleting <name> <loca- “<name> <location> deleted” and then 1. Press the SPEECH button (except for vehicles with Mitsubishi Multi-Commu- tion>.” the system will return to the main menu. nication System) or PICK-UP button (for If multiple telephone numbers are regis-...
Page 218 1. Press the SPEECH button (except for To import a devices phonebook When the deletion is complete, the voice vehicles with Mitsubishi Multi-Commu- guide will say “Hands-free system phone- nication System) or PICK-UP button (for Follow the steps below to transfer to the book erased”...
Page 219 Bluetooth® 2.0 interface (if so equipped) 5. The voice guide will say “Importing the 6. When the transfer is complete, the voice The term “IC:” before the radio certification contact list from the mobile phonebook. guide will say “Import complete” and number only signifies that Industry Canada This may take several minutes to com- then the system will return to the main...
Page 220: Usb Input Terminal (If So Equipped)
USB input terminal (if so equipped)  Connect the equipment into an outlet on a Refer to the following sections for details on 3. Connect a commercially available USB circuit different from that to which the how to play music files: connector cable (C) to the USB memory receiver is connected.
Page 221 USB input terminal (if so equipped) 2. Open the USB input terminal cover (A) in 4. Connect the Dock connector (C) to the CAUTION the floor console box. USB input terminal (D).  Keep the lid of the floor console box closed while driving the vehicle.
Page 222: Sun Visors
Sun visors Apple Inc. in the United States and other ory device or other device supporting mass Types of connectable devices countries. storage class. and supported file specifica- tions Item Condition NOTE MP3, WMA, AAC, N00567000015  Depending on the type of the USB memory File format device or other device connected, the con- Device types...
Page 223: 12 V Power Outlets
12 V power outlets Vanity mirror Type 2 12 V power outlets N00525000598 A vanity mirror is fitted to the back of the sun visor. CAUTION Type 1  Be sure to use a “plug-in” type accessory A vanity mirror is fitted to the back of the sun operating at 12 V and at 120 W or less.
Page 224: Interior Lights
Interior lights Type 1 Floor console box Accessories can be operated while the igni- tion switch or the operation mode is in ON or ACC. Floor console 1- Cargo room light  P.5-163 2- Dome light (Rear) (if so equipped)  Interior lights P.5-162 3- Dome light (Front)/Reading lights ...
Page 225 It goes off approxi- (if so equipped)  The time until the light goes off can be mately 30 seconds after the door or lift- adjusted. See your authorized Mitsubishi N00525801258 gate is closed. Motors dealer for details.
Page 226 It goes off approxi-  The time until the light goes off can be mately 30 seconds after the door or lift- adjusted. See your authorized Mitsubishi gate is closed. Motors dealer for details. However, the light goes off immediately...
Page 227 See The sunshade illumination turns on when the your authorized Mitsubishi Motors dealer for ignition switch or the operation mode is in The sunshade illumination also turns on when details.
Page 228: Storage Spaces
 The interior light auto-cutout function can be deactivated. The time until the lights automatically go off can be adjusted. See your authorized Mitsubishi Motors dealer for details. NOTE  When the lights are illuminated with the light switch in the “...
Page 229 Storage spaces Type2 Upper and lower boxes are located inside the floor console box. NOTE  The floor console box can also be used as an arm rest. Refer to the “Arm rest” section on page 4-6. NOTE Floor console box ...
Page 230: Cup Holders
Cup holders Tissue holder Upper box To open the upper box, lift the right release The tissue holder (D) is located on the under- lever (B) and raise the lid. side of the floor console box lid. Type 1 Type 2 For the front seat The cup holder is located in front of the floor console.
Page 231: Bottle Holders
Bottle holders For the rear seat To install (if so equipped) N00537001198 1. Insert the concave portion (A) on the In order to use the cup holder, allow the arm underside of the cargo area cover into the rest (A) to drop down. inside protruding portion (B) of the lift- gate.
Page 232: Assist Grips
Assist grips 2. Hang the strap (C) of the cargo area cover on the hook (D). CAUTION WARNING  Do not use the assist grips when getting into  Do not put a hanger or any heavy or or out of the vehicle. The assist grips could pointed object on the coat hook.
Page 233: Luggage Hooks
Luggage hooks Luggage hooks N00528500259 There are hooks on the sides of the luggage compartment for use in securing luggage. CAUTION  Do not load the luggage higher than the top of the seatback. Be sure that luggage is firmly secured. Restricted rear vision or flying objects enter- ing the passenger compartment during sud- den braking could result in a serious...
Page 234 Driving safety Driving precaution ................6-2 Fuel economy ...................6-2 Driving, alcohol and drugs ..............6-2 Floor mat ..................6-3 Vehicle preparation before driving ..........6-4 Safe driving techniques ..............6-4 Driving during cold weather ............6-5 Braking ....................6-5 Parking .....................6-6 Loading information ................6-7 Cargo loads ..................6-10 Trailer towing ................6-12 I n f o r ma t i o n P r o v i d e d b y :...
Page 235: Driving Precaution
Driving precaution cle, always make certain that you and all your  Always keep your vehicle well main- Driving precaution passengers are properly wearing their seat tained. A poorly maintained engine belts (with children in the rear seat, in appro- wastes fuel and costs money.
Page 236: Floor Mat
NOTE stalled. with the operation of the pedals, Mitsubishi  The shape of the mat and the number of • While the vehicle is stopped with the genuine floor mats are recommended.
Page 237: Vehicle Preparation Before Driving
 Make sure that infants and small children only by an authorized Mitsubishi Motors are properly restrained in accordance with  Drive defensively. Be aware of traffic, dealer. all laws and regulations.
Page 238: Driving During Cold Weather
Have the vehicle serviced by an let a skilled mechanic do it. authorized Mitsubishi Motors dealer or a repair facility of your choice at regular inter-  Warm the engine sufficiently. After start- vals according to the “WARRANTY AND...
Page 239: Parking
Parking cially when the brakes are wet, to confirm transaxle. When this happens, it is difficult to Parking they work normally. move the selector lever out of the “P” A film of water can be formed on the brake N00629600304 (PARK) position.
Page 240: Loading Information
Loading information installed options, if any, being towed. The tire  Curb weight: the weight of a motor vehi- WARNING and loading information placard located on cle with standard equipment including the  Do not park your vehicle in areas where maximum capacity of fuel, oil, and cool- the driver’s door sill of your vehicle will combustible materials such as dry grass or...
Page 241 Loading information Subtract the combined weight of  Occupant distribution: Occupant distribu- included in the definition of “cargo” when tion within the passenger compartment (In determining the vehicle capacity weight. This the driver and passengers from your vehicle the distribution is 2 in front, placard also tells you the size and recom- XXX kg or XXX lbs.
Page 242 Loading information If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. NOTE The above steps for determining ...
Page 243: Cargo Loads
Cargo loads NOTE The following table shows examples on how to calculate total cargo/load capacity of your vehicle with varying  seating configurations and number and size of occupants. This table is for illustration purposes only and may not be accurate for the seating and load capacity of your vehicle. For the following example the combined weight of occupants and cargo should never exceed 865 lbs (392 kg).
Page 244 Cargo loads occupants from the vehicle capacity weight. WARNING WARNING For additional information, if needed, refer to  Do not load cargo or luggage higher than  The total weight of all occupants and lug- “Steps for Determining Correct Load Limit” the top of the seatback.
Page 245: Trailer Towing
Trailer towing CAUTION Refitting the covers  Before driving and after traveling a short dis- 1. With each cover, put the tabs (C) on the tance, always check the load to make sure it cover in the holes (D) in the roof. is securely fastened to the roof carrier.
Page 246 Trailer towing WARNING  Do not use this vehicle for trailer towing. It may not be possible to maintain control or adequate braking. I n f o r ma t i o n P r o v i d e d b y : Driving safety 6-13...
Page 247 I n f o r ma t i o n P r o v i d e d b y :...
Page 248 Comfort controls Vents ....................7-2 Manual air conditioning-Type 1 (if so equipped) ......7-4 Manual air conditioning-Type 2 (if so equipped) ......7-9 Automatic air conditioning-Type1 (if so equipped) ......7-14 Automatic air conditioning-Type2 (if so equipped) ......7-20 Important air conditioning operating tips ........7-25 Air purifier ..................7-25 AM/FM radio/CD player (if so equipped)........7-26 Handling of Discs ................7-29...
Page 249: Vents
Vents 2- Open Vents N00729900249 NOTE  On rare occasions, air from the vents of an air-conditioned vehicle may be foggy. This is only moist air cooling suddenly and does not indicate a problem.  Do not let drinks or other liquids get into the vents as they could prevent the air condition- ing from operating normally.
Page 250 Vents NOTE  With the mode selection dial between the “ ” and “ ” positions, air flows mainly to the upper part of the passenger compart- ment. With the mode selection dial between the “ ” and “ ” positions, air flows mainly to the leg area.
Page 251: Manual Air Conditioning-Type 1 (If So Equipped)
Manual air conditioning-Type 1 (if so equipped) C- Blower speed selection dial Temperature control dial D- Air conditioning switch N00736600222 E- Mode selection dial Turn the temperature control dial clockwise Electric rear window defogger to make the air warmer. Turn it counterclock- switch...
Page 252 Manual air conditioning-Type 1 (if so equipped) If the outside air is dusty or contaminated in Mode selection dial some way, use the recirculation position. N00736700151 Switch to the outside air position every now To change the amount of air flowing from the and then to keep the windows from fogging vents, turn the mode selection dial.
Page 253 If it does blink, have it checked at an authorized Mitsubishi Motors dealer or a repair facility of your choice. I n f o r ma t i o n P r o v i d e d b y :...
Page 254 Manual air conditioning-Type 1 (if so equipped) NOTE Cooling  Sometimes, for example after using a high- N00731201350 pressure car wash, the condenser can get wet, For ordinary cooling and the air conditioning indicator light (A) blinks temporarily. Wait for a while, press the air conditioning switch once to turn the system off, then once more to turn it back on.
Page 255 Manual air conditioning-Type 1 (if so equipped) NOTE NOTE  To cool the leg areas, set the mode selection  When the temperature control dial is set to a position other than “MAX A/C”, the air dial to the “ ”...
Page 256: Manual Air Conditioning-Type 2 (If So Equipped)
Manual air conditioning-Type 2 (if so equipped) 1. Set the mode selection dial to the “ ” Manual air conditioning- position. Type 2 (if so equipped) 2. Set your blower to the maximum speed. 3. Set the temperature to the highest posi- N00730300298 tion.
Page 257 Manual air conditioning-Type 2 (if so equipped) Turning the dial clockwise will increase the blower speed; turning the dial counterclock- wise will decrease it. When the dial is set to the “OFF” position, all fan-driven airflow will stop. NOTE Air selection switch ...
Page 258 Manual air conditioning-Type 2 (if so equipped) and then to keep the windows from fogging  Changing the settings Press the air selection switch for about 10 seconds or longer. When the setting has changed, the system CAUTION will beep and the indicator light will flash. ...
Page 259 (A) does not blink, there is no problem. If it does blink, have it checked at an authorized Mitsubishi Motors dealer or a repair facility of your choice. I n f o r ma t i o n P r o v i d e d b y :...
Page 260 Manual air conditioning-Type 2 (if so equipped) Cooling Combination of unheated air and Defrosting or defogging (wind- heated air shield, door windows) N00731200311 N00731300266 N00731401583 Set the mode selection dial to the positions CAUTION shown in the illustration and set the air selec- tion switch (A) to the outside air position.
Page 261: Automatic Air Conditioning-Type1 (If So Equipped)
Automatic air conditioning-Type1 (if so equipped) 1. Set the mode selection dial to the “ ” NOTE Automatic air conditioning- position. Type1  While the mode selection dial is set to the (if so equipped) 2. Select your desired blower speed by turn- “...
Page 262 When the dial is set to air conditioning switch to match your per- sonal preferences. the “OFF” position, all fan-driven airflow Contact your Mitsubishi Motors dealer or a will stop. repair facility of your choice for assistance. Refer to “Personalizing the air conditioning switch (Changing the function setting)”...
Page 263 Automatic air conditioning-Type1 (if so equipped) page7-16.  Outside air {Indicator light (A) OFF} CAUTION Outside air is introduced into the passen-  Using recirculated air for a long time may ger compartment. Mode selection dial cause the windows to fog up. ...
Page 264 Press the air selection switch for about 10 no problem. If it does blink, have it checked seconds or longer. at an authorized Mitsubishi Motors dealer or When the setting has changed, the system a repair facility of your choice.
Page 265 Automatic air conditioning-Type1 (if so equipped)  Enable automatic air conditioning control: 2. Select the temperature control dial to the NOTE When the mode selection dial or blower desired temperature. The temperature can  While the mode selection dial is set between speed selection dial has been set to the be set within a range of around 61 to 89.
Page 266 Automatic air conditioning-Type1 (if so equipped) the desired positions. To return to automatic leg area heated (when driving in rain or  For quick defrosting operation, set the dials to the “AUTO” posi- snow). tion. Defrosting or defogging (wind- shield, door windows) N00732401492 CAUTION ...
Page 267: Automatic Air Conditioning-Type2 (If So Equipped)
Automatic air conditioning-Type2 (if so equipped) NOTE NOTE  When defrosting, do not set the temperature  There is an interior air temperature sensor control dial to the maximum cool position. (G) in the illustrated position. This will blow cool air on the window glass Never place anything over the sensor, since and fog it up.
Page 268 Contact your Mitsubishi Motors dealer or a Switch to the outside air position every now shield. repair facility of your choice for assistance.
Page 269 • When the setting has changed from no problem. If it does blink, have it checked enabled to disabled, at an authorized Mitsubishi Motors dealer or the system will beep three times and the a repair facility of your choice.
Page 270 Automatic air conditioning-Type2 (if so equipped)  Changing the settings NOTE Operating the air conditioning Press the air conditioning switch for about system (automatic mode)  Sometimes, for example after using a high- 10 seconds or longer. pressure car wash, the condenser can get wet, When the setting has changed, the system N00731700286 and the air conditioning indicator light (A)
Page 271 Automatic air conditioning-Type2 (if so equipped) To remove frost or mist from the windshield NOTE  For quick defrosting and door windows, use the mode selection  Set the temperature at about 25 under normal dial (“ ” or “ ”).
Page 272: Important Air Conditioning Operating Tips
Have the system inspected by your authorized in the best operating condition. Mitsubishi Motors dealer or a repair facility N00733700280 1. Park the vehicle in the shade whenever of your choice.
Page 273: Am/Fm Radio/Cd Player (If So Equipped)
How to Clean audio system and have it checked at an The audio system can only be used when the authorized Mitsubishi Motors dealer or a ignition switch or the operation mode is in N00715200023 repair facility of your choice. Never try to ...
Page 274 AM/FM radio/CD player (if so equipped)  Furthermore, even if there is no specific denotation of trademarks or registered trademarks, these are to be observed in their entirety. “Made for iPod”, “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple...
Page 275 AM/FM radio/CD player (if so equipped) 5th generation 5th generation 160GB (2009) 160GB (2007) 80GB (video) (video) 60GB 80GB 30GB 6th generation 5th generation 4th generation (video) 8GB 16GB (video camera) 8GB 16GB 8GB 16GB 3rd generation 2nd generation 1st generation (video) (aluminum) 1GB 2GB 4GB...
Page 276: Handling Of Discs
Handling of Discs 4th generation 3rd generation 2nd generation 1st generation 8GB 32GB 64GB 32GB 64GB 8GB 16GB 32GB 8GB 16GB 32GB 16GB 32GB 64GB 16GB 32GB 8GB 16GB 32GB 8GB 16GB handling of discs. N00715400025 Handling of Discs This explains care that should be taken in the I n f o r ma t i o n P r o v i d e d b y : Comfort controls 7-29...
Page 277 Handling of Discs  If discs are not going to be used for a long Maxi- Important Points on Handling period of time, remove these from the Com- Type Size product.  Fingerprints or other marks on the read playback ments surface of the disc may result in its con- time...
Page 278: Audio Files (Mp3/Wma/Aac)
Audio Files (MP3/WMA/AAC)  Discs that have not been finalized cannot  When playing back non standard CDs, the CAUTION be played back. following may occur.  CD-ROM and CD-R/RW media can only  Even if recorded using the correct format •...
Page 279 Audio Files (MP3/WMA/AAC) Data Formats That Can Be Speci- Name fica- Explanation ROOT Played Back Folder tion N00715700031 Audio file Format ISO96 Level 1 Maximum 8 Data formats that can be played on discs specifica- character file (CD-ROM, CD-R/RW) and USB devices dif- tions name, and 3 fer.
Page 280 Audio Files (MP3/WMA/AAC) Speci- What Is MP3? Item Details Name fica- Explanation Specification MPEG-1 AUDIO LAYER3 N00715900033 tion MP3 is an abbreviation of “MPEG-1 Audio MPEG-2 AUDIO LAYER3 Maxi- 65,535 files (total number on Layer 3”. MPEG is an abbreviation of Sampling MPEG-1: 32/44.1/48 mum file...
Page 281 Audio Files (MP3/WMA/AAC) What Is WMA? Item Details CAUTION Specification Windows Media Audio  AAC supports digital rights management N00716000031 Version7.0/8.0/9.0 (DRM). This product cannot play back AAC WMA is an abbreviation of Windows Media files protected using this system. Audio, and this is an audio compression for- Sampling fre- 32/44.1/48...
Page 282: Important Points On Safety For The Customer
WARNING smell, immediately stop using the product, and consult an authorized Mitsubishi  The driver should not pay close attention Motors dealer or a repair facility of your to the display while driving.
Page 283: Operation Keys
Operation Keys Adjust Volume Insert/Eject Discs Operation Keys N00716500023 N00716600024 N00716300021 1. Turn the PWR/VOL key to adjust the vol- 1. Insert the disc into the disc slot with the ume. label surface up. Turn the Power ON/ OFF N00716400022 1.
Page 284 Operation Keys Explanation of Buttons N00716700025 This explains names and functions of each part. 5- RADIO key 9- PTY key Switch the radio and the band. PTY searches and scans can be per- Use to eject a disc. 6- PWR/VOL key formed while receiving radio RBDS 2- 3 key/4...
Page 285: Listen To Radio
Listen to Radio 13- 5 Steering wheel audio remote Play/Pause Bluetooth Audio* , and use CD or MP3 control switch as preset key 5 for radio. iPod* or USB device N00716800068 14- 6 Bluetooth Audio* Return during audio track search, and stop Bluetooth Audio* FM1, 2 For radio, use as preset key 6.
Page 286 Listen to Radio Press the SCAN key. NOTE PTY Search  Bands switch in the order AM, FM1, FM2, When a station is received, this is played for 5 SIR1*, SIR2*, SIR3*, and SIR4*. seconds, then the product searches for the During RBDS broadcast reception, select ...
Page 287: Listen To Satellite Radio (If So Equipped)
Listen to Satellite Radio (if so equipped) 1. During FM reception, press the PTY key. To listen to Satellite Radio While the key is held down, This switches to the PTY selection mode. it will cycle down through (Hold down) 2.
Page 288 Listen to Satellite Radio (if so equipped) 2. Hold down any of the keys from the 1RPT 4. Turn the /SEL key to select the chan- NOTE key to the 6 key. nel.  Selecting a channel will also cancel scan A “Beep”...
Page 289: Listen To Cds
Listen to CDs If a disc is already within the product, press NOTE NOTE the MEDIA key to switch to CD as the  In the channel preliminary setting mode,  Pressing again will cancel. source.  Selecting a track, ejecting, fast forwarding, press the 6 key to return to the category or rewinding will cancel.
Page 290: Listen To Mp3S
Listen to MP3s This enables selection of the next or previous Repeat playback of the tracks within the Listen to MP3s track. folder currently being played. N00717200030 This explains how to listen to audio files on a NOTE Fast Forward or Rewind disc.
Page 291: Listen To An Ipod
Listen to an iPod Scan Playback (SCAN) NOTE CAUTION  If there is no operation for 10 seconds after  Depending on how the devices are handled, selecting the folder, then track search mode audio files being damaged or lost, therefore Press the SCAN key.
Page 292 Listen to an iPod NOTE Play iPod Repeat Playback (RPT)  Depending on the status of the iPod/iPhone, it may take some time until the device is rec- Press the 1RPT key. Press the MEDIA key to set the iPod as the ognized, or playback starts.
Page 293: Listen To Audio Files On A Usb Device
Listen to Audio Files on a USB Device NOTE NOTE CAUTION  Pressing again will cancel.  Select the category, and hold down the  Do not use hard discs, card readers, or mem- ory readers, as damage may occur to these or /SEL key to start playback from the first to the data contained therein.
Page 294 Listen to Audio Files on a USB Device NOTE NOTE Switch Playback Mode  Set up the device in order that no unsafe  The maximum supported capacity for USB actions, such as plugging in the connection memory is 32GB. Repeat playback, random playback, and scan cable are taken while driving.
Page 295 Listen to Audio Files on a USB Device NOTE NOTE Search Tracks  Cycling up/down through files will cancel  Selecting a folder will cancel this. this.  Cycling up/down through files will cancel Search folders and files, and select a track. ...
Page 296: Listen To Bluetooth Audio (If So Equipped)
Listen to Bluetooth Audio (if so equipped) NOTE Play Bluetooth Audio Listen to Bluetooth Audio  Depending on the status of the Bluetooth so equipped) 1. Press the MEDIA key to set Bluetooth audio device, it may take some time until the Audio as the source.
Page 297 Listen to Bluetooth Audio (if so equipped) Switch Playback Mode Scan Playback (SCAN) Press the SCAN key. Repeat playback, random playback, and scan playback are possible. Play the first 10 seconds of each track on the Bluetooth Audio device in order. Repeat Playback (RPT) NOTE Press the 1RPT key.
Page 298: Display Indicator
Display Indicator Display Indicator N00717700022 This explains content of the display indicator. During FM Reception Change the Display Mode CAUTION  The operation of changing display contents N00717800036 may impede safe driving, therefore check This switches in the order “Frequency”, “Sta- You can change the content of the display safety before operation.
Page 299: Audio Quality And Volume Balance Adjustment
Audio Quality and Volume Balance Adjustment During Satellite Radio Reception NOTE NOTE (if so equipped)  If there is no text information to display, then  If there is no text information to display, then “NO TITLE” is displayed. “NO TITLE” is displayed. ...
Page 300: System Settings
System Settings 2. Press the /SEL key to select settings Adjust- Turn counter- items. ment Turn clockwise clockwise items Each time the /SEL key is pressed, this BASS -6 to 0 0 to +6 switches in the order Satellite radio set- (low low-pass (high low-pass tings*...
Page 301 System Settings Satellite Radio Settings (if so equipped) Change each satellite radio setting. Settings Settings name Settings item Settings content value SIRIUS ID — — This displays the SIRIUS ID. SKIP SETTING SKIP SETTING SKIP can be set for each channel. Channels for which SKIP is set are excluded from the search during up/down channel selecting and scanning.
Page 302 System Settings :Once the CODE (passcode) of your choice is entered, each time the /SET key is pressed, this switches in the order Settings channel select, Change LOCK settings, and Complete settings. To return to “each channel LOCK setting”, press the 6 key.
Page 303: Troubleshooting
Troubleshooting Settings Gracenote DB (Vehicles with a ® Vehicles with a Bluetooth 2.0 Interface Settings content value ® Bluetooth 2.0 interface) (“Set value” bold typeface indicates factory PHONE During mobile phone voice cut- default settings.) IN-L in, output sound from the left The version number can be confirmed.
Page 304 The drive has malfunctioned for some reason. Check that there is no problem with the disc, and insert the disc again. If the problem persists, con- sult an authorized Mitsubishi Motors dealer or a repair facility of your choice. HEAT ERROR The temperature inside the product is high.
Page 305: Antenna
Antenna If You Think Something Is Not Working Properly... Here is a list of symptoms, causes and responses if you think something is not working properly. Symptoms Cause Response There is no sound or quiet The volume is turned to its minimum. Adjust the volume.
Page 306: General Information About Your Radio
General information about your radio (for vehicles sold in U.S.A.). Operation is subject to the following conditions:  The device may not cause harmful inter- ference.  This device must accept any interference received, including interference that may cause undesirable operation. 25 to 40 mile radius 100 mile radius (40 to 64 km)
Page 307 General information about your radio The direct signal from the broadcast station lines, lightning and other types of similar reaches the antenna slightly before the electrical phenomena. reflected signal. This time difference may cause some reception disturbance or flutter. This problem occurs primarily in urban areas. FM stereo reception Stereo reception requires a high quality broadcast signal.
Page 308 For emergencies If the vehicle breaks down ...............8-2 Jump-starting the engine ..............8-2 Engine overheating ................8-4 Jack and tools ...................8-5 How to change a tire ................8-5 Towing ...................8-12 Operation under adverse driving conditions ........8-13 Fuel Pump Shut-off System ............8-15 I n f o r ma t i o n P r o v i d e d b y :...
Page 309: If The Vehicle Breaks Down
If the vehicle breaks down 2. Position the vehicles close enough If the vehicle breaks down Jump-starting the engine together so that the jumper cables can N00836300187 N00836401781 reach, but be sure the vehicles aren’t If your vehicle breaks down on the road, If the engine cannot be started because the touching each other.
Page 310 Jump-starting the engine 5. Connect one end of one jumper cable to 6. Connect one end of the other jumper cable 8. After the engine is started, disconnect the the positive (+) terminal of the discharged to the negative (-) terminal of the booster cables in the reverse order from the way battery (A), and the other end to the posi- battery (B), and the other end to the...
Page 311: Engine Overheating
Look for obvious brakes leaks, such as a split radiator hose. Be immediately and contact an authorized Mitsubishi Motors dealer or a repair facil- careful as components will be hot. Any ity of your choice for assistance. leak source must be repaired.
Page 312: Jack And Tools
 Never get under the vehicle or put any 11. Have the system inspected by your autho- portion of your body under the vehicle rized Mitsubishi Motors dealer or a repair while it is supported by the jack. facility of your choice.
Page 313 Have the tire replaced or repaired at an authorized ment. It is designed to save space in the lug- Mitsubishi Motors dealer or a repair facility gage compartment. Its lighter weight makes it of your choice as soon as possible.
Page 314 How to change a tire 2. Place the jack under one of the jacking CAUTION To change a tire points (A) shown in the illustration. Use  Do not use tire chains with your compact N00849801460 the jacking point closest to the tire you 1.
Page 315 How to change a tire 4. Insert the bar (D) into the wheel nut NOTE WARNING wrench (E). Then put the end of the bar  Put the spare wheel under the vehicle body  No one should be in your vehicle when into the shaft’s jack end, as shown in the near the jack.
Page 316 How to change a tire 7. [Vehicle with the tapered nuts] • Steel wheel WARNING Install the wheel nuts with their tapered Install the wheel nuts with their tapered  Mount the spare wheel with the valve stem ends facing inward, then tighten by hand ends facing inward, then tighten by hand (I) facing outward.
Page 317 Refer to after changing the tire, have the tire checked “Tire inflation pressures” on page 9-17. for balance at an authorized Mitsubishi 9. Tighten the nuts in the order shown in the Motors dealer or a repair facility of your illustration until each nut has been tight- choice.
Page 318 How to change a tire 1. Align the tire air valve (C) and the wheel Wheel cover CAUTION (if so equipped) cover notch (D).  Trying to remove the wheel cover with only N00849400195 your bare hands can seriously injure your fingers.
Page 319: Towing
Towing 4. Gently tap around the circumference of CAUTION the wheel cover at the top (H), then push  Do not attempt to be towed by another vehi- the wheel cover into place. cle with a rope. NOTE  Do not use the tie-down hooks for towing. These hooks are provided only for the pur- pose of transporting the vehicle itself.
Page 320: Operation Under Adverse Driving Conditions
Operation under adverse driving conditions Towing the vehicle by a tow CAUTION Towing a front-wheel drive vehi- cle with front wheels off the truck  [For front-wheel drive vehicle equipped with the active stability control (ASC)] ground (Type C) If the vehicle is towed with the ignition CAUTION switch in the “ON”...
Page 321 Operation under adverse driving conditions  After parking on snowy or icy road, it WARNING On snowy or icy roads may be difficult to move your vehicle due  When trying to rock your vehicle out of a to freeze-up of the brake. Depress the ...
Page 322: Fuel Pump Shut-Off System
If a fuel leak is found or a fuel odor is detected, do not restart the engine.  Mitsubishi Motors recommends that your vehicle be inspected by an authorized Mit- subishi Motors dealer after any collision.
Page 323 I n f o r ma t i o n P r o v i d e d b y :...
Page 324 Vehicle care and maintenance Service precautions ................9-2 Cleaning the outside of your vehicle ..........9-40 Catalytic converter ................9-2 Engine hood ..................9-3 View of the engine compartment .............9-5 Engine oil and oil filter ..............9-5 Engine coolant .................9-7 Air cleaner filter ................9-8 Manual transaxle oil (if so equipped) ..........9-10 Continuously variable transmission (CVT) fluid (if so equipped) .................9-10 Transfer oil (All-wheel drive models) ...........9-11...
Page 325: Service Precautions
Have you purchased the Mitsubishi Motors Mitsubishi Motors dealer or a repair facility  Do not get under your vehicle while it is on Diamond Care Protection Plan? The Plan of your choice.
Page 326: Engine Hood
Have your vehicle  Do not put undercoat paint on the cata- checked at an authorized Mitsubishi lytic converter. Motors dealer or a repair facility of your choice as soon as possible.
Page 327 Engine hood Release the lever and lift the engine hood. CAUTION CAUTION  Always insert the support prop into the hole  Make sure the engine hood is firmly closed specially made for it. Propping the engine before driving. hood at any other place could cause the prop If you drive without the engine hood com- to slip out and lead to an accident.
Page 328: View Of The Engine Compartment
View of the engine compartment View of the engine compart- Engine oil and oil filter ment N00937702053 Good N00937600625 To check and refill engine oil It is normal for an engine to use oil. You may need to add oil between the recommended oil change intervals.
Page 329 Engine Oil is recommended for optimum fuel economy and cold weather starting. Mitsubishi Motors recommends using only If Mitsubishi Motors Genuine 0W-20 Syn- 1- The upper part indicates the quality of engine oils with the ILSAC certification sym- thetic Engine Oil is not available, 5W-20 the oil.
Page 330: Engine Coolant
To add coolant CAUTION of 256 psi (1.8 MPa). A Genuine Mitsubishi  The required concentration of anti-freeze dif- oil filter is the best replacement filter. fers depending on the expected ambient tem- Use “Mitsubishi Motors Genuine Super Long...
Page 331: Air Cleaner Filter
Motors dealer or a repair facility of your NOTE choice to have the thermostat checked, and replaced if necessary.  Genuine Mitsubishi Motors Parts are recom- mended when replacing the air cleaner filter.  Make sure that the connector is properly reconnected.
Page 332 Air cleaner filter 2. Remove the clips (C), and then remove NOTE WARNING the air duct (D).  After replacing the air cleaner filter, make  Turn the ignition switch to the “OFF” sure that the hinges at the bottom of cover position or put the operation mode in are firmly set.
Page 333: Manual Transaxle Oil (If So Equipped)
(CVT) should be maintained and serviced by an authorized Mitsubishi Motors dealer or a repair facility of your choice to obtain the best performance and longest life. It is impor- tant that the transmission fluid is kept at the correct level.
Page 334: Transfer Oil (All-Wheel Drive Models)
Fill the reservoir with windshield anti- freeze (not radiator antifreeze), and operate Mitsubishi Motors Genuine N00938400271 the system for a few seconds to flush out the Lubricant Super Hypoid Gear Oil API Whenever the transfer oil level is checked, residual water.
Page 335: Battery
The fluid in the master cylinder should be rized Mitsubishi Motors dealer or a repair checked when doing other work under the Battery facility of your choice before the start of cold engine hood.
Page 336: Tires
Tires NOTE WARNING NOTE  Loosen the nut (B) and then disconnect the • If electrolyte gets on plastic parts or  Check to see that the battery is securely battery cable from the positive (+) terminal. other nearby parts, wipe it off with a soft installed and cannot be moved.
Page 337 Tires  Cold tire pressure:  Light truck (LT) tire: a tire designated by  Groove: the space between two adjacent • The measured pressure after the vehicle its manufacturer as primarily intended for tread ribs. use on lightweight trucks or multipurpose has been parked for at least three hours, passenger vehicles.
Page 338 Tires Construction code Speed symbol NOTE •“R” means radial construc- A symbol indicating the LT (Light Truck) -metric tire  tion. range of speeds at which a sizing is based on U.S.A. design •“D” means diagonal or bias tire can carry a load corre- standards.
Page 339 Tires EXAMPLE: DOT MA L9 ABCD WARNING Treadwear, Traction and Temper- 1504 ature Grades Overloading of your tire is  Department of Transporta- dangerous. Overloading can tion cause tire failure, affect vehi- Treadwear This symbol certifies that the cle handling, and increase tire is in compliance with the The treadwear grade is a comparative your stopping distance.
Page 340 Tires under controlled conditions on speci- The tire pressure for your vehicle under nor- Tire inflation pressures mal driving conditions is listed on the placard fied government test surfaces of N00939301955 attached to the driver’s door sill. asphalt and concrete. A tire marked Proper tire inflation pressure is essential for (Refer to “Tire and loading information plac- C may have poor traction perfor-...
Page 341  Stay within the recommended load limits.  Only Mitsubishi Motors Authorized wheels  Make sure that the weight of any load in should be used, because your vehicle is your vehicle is evenly distributed.
Page 342 To even out the wear on your tires and make potential. them last longer, Mitsubishi Motors Corpora- Tires that have arrows showing rotation direction tion recommends that you rotate your tires at Front the mileage listed in the “WARRANTY AND...
Page 343: Clutch Pedal Free Play (If So Equipped)
75 mph (120 km/h). N00940201101 CAUTION To check the clutch pedal free play (A), turn  Only Mitsubishi Motors Authorized wheels off the engine and press the pedal until you should be used, because your vehicle is feel resistance.
Page 344: Parking Brake
Replace the blades if they continue to streak maintained by an authorized Mitsubishi ratchet. You should feel the parking brake or smear. Motors dealer or a repair facility of your grab between 6 to 7 notches (clicks).
Page 345: General Maintenance
Have the system checked at an authorized “WARRANTY MAINTENANCE Mitsubishi Motors dealer. Mitsubishi Motors dealer at the mileage spec- MANUAL”. ified in the “WARRANTY AND MAINTE- Fuel system (tank, pipe line and NANCE MANUAL”. NOTE connection, and fuel tank filler ...
Page 346 Any open seams or loose problem with them. grease leaks: connections could let dangerous exhaust See your authorized Mitsubishi Motors dealer  Ball joint boots of the front suspension fumes seep into the luggage compartment and for assistance, if you have any questions.
Page 347: For Cold And Snowy Weather
In case of a melted fusible link, see your The ventilation slots in front of the wind- authorized Mitsubishi Motors dealer or a shield should be brushed clear after a heavy repair facility of your choice for inspection snowfall so that the operation of the heating and replacement.
Page 348 Fuses Engine compartment Passenger compartment fuse loca- Main fuse block tion table 1. Insert a screwdriver into the notch of the fuse lid and pry gently to remove it. In the engine compartment, the fuse block is Passenger compartment fuse location located as shown in the illustration.
Page 349 Fuses Sym- Capac- Sym- Capac- Engine compartment fuse location Electrical system Electrical system table Power window con- Windshield wiper 30 A 30 A* trol Engine compartment fuse location Optional 10 A Defogger 30 A* Door locks 20 A Heated door mirror 7.5 A Radio 15 A...
Page 350 Fuses Sym- Capac- Sym- Capac- Sym- Capac- Electrical system Electrical system Electrical system Headlight Alternator 7.5 A Audio amplifier 30 A (low Halogen 10 A Headlight washer 20 A Diesel 30 A beam) (left) — Spare fuse 10 A Air conditioning 10 A Headlight —...
Page 351 If the fuse is not Capacity Color blown, something else must be causing the problem. Have the system inspected 7.5 A Brown by your authorized Mitsubishi Motors 10 A dealer or a repair facility of your choice. 15 A Blue 20 A Yellow...
Page 352: Replacement Of Light Bulbs
 If you are unsure of how to carry out the work as required, it is recommended that these procedures be carried out by an autho- rized Mitsubishi Motors dealer or a repair facility of your choice.  Be careful not to scratch the vehicle body when removing a light and lens.
Page 353 Replacement of light bulbs WARNING NOTE Rear  Check with an authorized Mitsubishi  The rear side-marker light, the tail and stop Motors dealer or a repair facility of your light and the high-mounted stop light use an choice when it is necessary to repair a high LED instead of the bulb.
Page 354 Replacement of light bulbs 2. Turn the bulb (B) counterclockwise to Item Wattage CAUTION remove it. Glove compartment light 1.4 W  Handle halogen light bulb with care. The gas inside a halogen light bulb is highly pressur- ized, so dropping, knocking, or scratching a Headlights (low beam, except halogen light bulb can cause it to shatter.
Page 355 Replacement of light bulbs 3. While holding down the tab (C), pull out Headlights (high beam) CAUTION the socket (D).  Never hold the halogen light bulb with a bare N00901901103 1. Turn the cap (A) counterclockwise to hand, dirty glove, etc. remove it.
Page 356 N00943200121 installing the upper cover and duct” on The alignment of the headlights should be page 9-9. checked by an authorized Mitsubishi Motors 2. Turn the socket (A) counterclockwise to dealer or a repair facility of your choice. remove it.
Page 357  It is not possible to repair or replace only the bulb for the side turn signal light. Check with an authorized Mitsubishi Motors dealer or a repair facility of your choice when the light needs to be repaired or replaced.
Page 358 (type 2) uses an LED instead of the bulb. hand, dirty glove, etc. The oil from your Check with an authorized Mitsubishi Motors hand could cause the bulb to break the next dealer or a repair facility of your choice time the fog lights are used.
Page 359  The rear side-marker light, and the tail and stop light uses an LED instead of the bulb. Check with an authorized Mitsubishi Motors dealer or a repair facility of your choice when the light needs to be repaired or replaced.
Page 360 Replacement of light bulbs 3. Turn the socket counterclockwise to 5. To install the bulb, perform the removal 2. Remove the socket (B) and bulb assembly remove it. steps in reverse. by turning it counterclockwise. NOTE  When installing the lid, align the tab on the lid with the hole on the vehicle side.
Page 361: Vehicle Care Precautions
 The high-mounted stop light uses an LED • Carbon Tetrachloride instead of the bulb. Check with an authorized NOTE Mitsubishi Motors dealer or a repair facility • Benzine  Always read the instructions on the cleaner of your choice when the light needs to be •...
Page 362 Cleaning the inside of your vehicle 2. To rinse, dip the cloth in fresh water, Plastic, vinyl leather, fabric and Upholstery wring it out well, and wipe off all the flocked parts N00945500128 soap. 1. To maintain the value of your new vehi- 3.
Page 363 Cleaning the outside of your vehicle clean water and a car washing mitt or sponge, CAUTION Cleaning the outside of your wash the vehicle from top to bottom. vehicle  Some hot water washing equipment uses Use a mild car washing soap if necessary. high pressure and heat to clean your vehicle.
Page 364 Cleaning the outside of your vehicle You should flush the underbody with a high CAUTION Damaged paint pressure hose every time you wash the out-  Waxes containing high abrasive compounds N00946200047 side of your vehicle. should not be used. These waxes remove rust Small cracks and scratches in the paint coat Take special care to remove mud or other and stain effectively from the paintwork, but...
Page 365 Cleaning the outside of your vehicle CAUTION CAUTION Engine compartment  Do not let plastic parts get soiled with gaso-  Do not use a brush or other hard implement N00947000071 line, oil, brake fluids, engine oils, greases, on the wheels. Never spray or splash water on the electrical paint thinner, and sulfuric acid (battery elec- ...
Page 366 Customer assistance/ Reporting Safety Defects Consumer information (For vehicles sold in U.S.A.) ....10-2 Reporting Safety Defects ...............10-2 Important facts to know in case of an accident ......10-4 I n f o r ma t i o n P r o v i d e d b y :...
Page 367 Administration (NHTSA) in addi- ) times as well on the government course heat when tested under controlled conditions tion to notifying Mitsubishi Motors as a tire graded 100. The relative performance on a specified indoor laboratory test wheel. North America, Inc.
Page 368 Reporting Safety Defects If NHTSA receives similar com- To contact Mitsubishi Motor Sales of For vehicles sold in U.S.A. plaints, it may open an investigation, Canada, Inc. call 1-888-576-4878 or and if it finds that a safety defect write to:...
Page 369 The strength and integrity built into your To contact Triple J Motors  Remain calm. Mitsubishi vehicle is the result of a specific  Check for injuries. Report all injuries to call (670)234-7133 or write to: design referred to as “Energy Management”.
Page 370 Mitsubishi Motors. I n f o r ma t i o n P r o v i d e d b y :...
Page 371 I n f o r ma t i o n P r o v i d e d b y :...
Page 372 Specifications Vehicle labeling ................11-2 Vehicle dimensions ................11-3 Vehicle weights ................11-3 Engine specifications ..............11-4 Battery ....................11-4 Tires and wheels ................11-5 Capacity ..................11-5 I n f o r ma t i o n P r o v i d e d b y :...
Page 373: Vehicle Labeling
Vehicle labeling 2 - Vehicle identification num- 4 - Vehicle information code Vehicle labeling ber plate plate (For vehicles sold in Mex- N01147401752 ico) Keep a record of the chassis number and vehicle identification number. Such informa- The vehicle identification number is stamped tion will assist police if your vehicle is stolen.
Page 374: Vehicle Dimensions
Vehicle dimensions Certification label Overall width 69.7 in (1,770 mm) Without N01148200167 64.2 in (1,630 mm) The certification label is located on the roof rails Overall driver’s door sill. height With roof 64.6 in (1,640 mm) rails Wheel base 105.1 in (2,670 mm) Vehicle dimensions N01147500479 Overall length...
Page 375: Engine Specifications
Engine specifications Maximum roof load 176 lb (80 kg) Seating capacity 5 persons NOTE  Roof load is important because it affects the vehicle capacity weight. Refer to “Loading cargo on the roof” on page 6-11. GVWR: maximum total weight (load) limit specified for the vehicle GAWR: maximum weight (load) limit specified for the front or rear axle Seating capacity: the maximum number of occupants Engine specifications...
Page 376: Tires And Wheels
Oil filter .32 qt (0.3 L) mission (CVT) Mitsubishi Motors Genuine NEW MULTI GEAR OIL API Manual transaxle 2.6 qt (2.5 L) classification GL-3 SAE 75W-80 Refer to “Continuously variable transmission (CVT) fluid” on Continuously variable transmission (CVT) 7.3 qt (6.9 L)
Page 377 Capacity Item Capacity Lubricants Mitsubishi Motors Genuine Super Hypoid Gear Oil API classi- Transfer oil .53 qt (0.5 L) fication GL-5 SAE 80 Mitsubishi Motors Genuine Super Hypoid Gear Oil API classi- Differential Rear axle .42 qt (0.4 L) fication GL-5 SAE 80...
Page 378 Alphabetical index Automatic transaxle Break-in recommendations ....5-3 Numerics Fluid ..........11-5 Bulb capacity........9-29 4-wheel drive operation ....... 5-58 Back-up light California Perchlorate Materials Bulb capacity ......... 9-29 Accessory (installation) ......3-6 Requirements ........3-6 Replacement ........9-36 Active stability control (ASC) ....5-68 Capacities ..........
Page 379 Alphabetical index Continuously variable transmission (CVT)..Driving precaution ....... 6-2 Continuously variable transmission (CVT) 5-49 fluid ........9-10, 11-5 Driving, alcohol and drugs ....6-2 Fluid ........9-10, 11-5 Engine coolant ......9-7, 11-5 Selector lever operation....5-49 Power steering fluid ......11-5 Selector lever positions ....
Page 380 Alphabetical index License plate light Bulb capacity ......... 9-29 Replacement........9-37 General maintenance If the vehicle breaks down..... 8-2 Liftgate ..........5-32 Maintenance........9-22 Ignition switch ........5-44 Inside liftgate release....... 5-33 General vehicle data......11-3 Important facts to know in case of an accident Link System ........
Page 381 Alphabetical index Operation under adverse driving conditions... Reading lights Seat belt force limitter..... 4-18 8-13 Bulb capacity........9-30 Seat belt pre-tensioners ....4-17 Seat belt use during pregnancy..4-17 Outside rearview mirrors ..... 5-43 Rear axle oil ......9-11, 11-5 Seats............
Page 382 Alphabetical index Maintenance service......4-41 Indicators ........5-117 Waxing ..........9-41 Lever ........... 5-127 Weights ..........11-3 Wheel Covers ........... 8-11 Tail light Specification ........11-5 Bulb capacity ......... 9-29 USB input terminal......5-157 Replacement ........9-35 How to connect an iPod ....5-158 Wiper Rear window wiper .......
Page 383 How to calculate your gasoline mileage You can calculate your miles-per-gallon or kilometers-per-litre 3. Refill the fuel tank. Record the odometer mileage again, by using the following process: as well as the gallons/litres of fuel used. 4. Subtract the first mileage number from the second number 1.
Page 384 N09348201058 NOTE Name of Owner Date of Purchase Address of Owner Model of Vehicle Name and Address of Dealer Vehicle Identification Number Maintenance record Kilometers Service Performed Date Inspection and Maintenance Item Miles I n f o r ma t i o n P r o v i d e d b y :...

Mitsubishi 2015 OUTLANDER SPORT/RVR Owner's Manual

General Information 3

Seat and Restraint Systems 4

Table of Contents

Driving Safety

Table of Contents

For Emergencies

Vehicle Care and Maintenance

Quick Links

Chapters

Related Manuals for Mitsubishi 2015 OUTLANDER SPORT/RVR

Summary of Contents for Mitsubishi 2015 OUTLANDER SPORT/RVR

Table of Contents