Korg PA 80 User Manual page 255

060: 4EqPhsrChFl
(Parametric 4-Band EQ – Chorus/Flanger)
This effect combines a mono-type four-band parametric
equalizer and a chorus/flanger.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Parametric 4Band EQ
+
Trim
Right
[E] Trim
a
Sets the parametric EQ input level
[E] Band1 Cutoff [Hz]
Sets the center frequency of Band 1
Q
b
Sets the bandwidth of Band 1
Gain [dB]
Sets the gain of Band 1
[E] Band2 Cutoff [Hz]
Sets the center frequency of Band 2
Q
c
Sets the bandwidth of Band 2
Gain [dB]
Sets the gain of Band 2
[E] Band3 Cutoff [Hz]
Sets the center frequency for Band 3
Q
d
Sets the bandwidth of Band 3
Gain [dB]
Sets the gain of Band 3
[E] Band4 Cutoff [Hz]
Sets the center frequency for Band 4
Q
e
Sets the bandwidth of Band 4
Gain [dB]
Sets the gain of Band 4
[F] Delay Time [msec]
f
Sets the delay time
[F] LFO Frequency [Hz]
Sets the LFO speed
g
LFO Waveform
Selects LFO Waveform
[F] Depth
Sets the depth of LFO modulation
h
Feedback
Sets the feedback amount
[F] Cho/Flng Wet/Dry
Sets the effect balance of the chorus/flanger
i
Output Mode
Selects the output mode for the chorus/flanger
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 1
Src
j
Table , "Selects the modulation source of the effect balance," on page 1
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 1
i: Output Mode
When Wet Invert is selected, the right channel phase of
the chorus/flanger effect sound is inverted. This creates
pseudo-stereo effects and adds spread.
Wet / Dry
Chorus/Flanger
Chorus/Flanger
Normal
+
Output Mode
–
Wet Invert
Feedback
Cho/Flng Wet / Dry
Wet / Dry
LFO: Tri / Sine
0...100
20...1.00kHz
0.5...10.0
☞
Fx:006
–18...+18dB
50...5.00kHz
0.5...10.0
☞
Fx:006
–18...+18dB
300...10.00kHz
0.5...10.0
☞
Fx:006
–18...+18dB
500...20.00kHz
0.5...10.0
☞
Fx:006
–18...+18dB
0.0...50.0msec
0.02...20.00Hz
Triangle, Sine
0...100
–100...+100
☞
Fx:020
–Wet...–2:98, Dry, 2:98...Wet
☞
Fx:010, 020
Normal, Wet Invert
☞
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
However, if a mono-input type effect is connected after
this effect, the left and right sounds may cancel each
other, eliminating the chorus/flanger effects.
061: Par4Eq-Phsr
(Parametric 4-Band EQ – Phaser)
This effect combines a mono-type four-band parametric
equalizer and a phaser.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Parametric 4Band EQ
+
Trim
Right
[E] Trim
a
Sets the parametric EQ input level
[E] Band1 Cutoff [Hz]
Sets the center frequency of Band 1
Q
b
Sets the bandwidth of Band 1
Gain [dB]
Sets the gain of Band 1
[E] Band2 Cutoff [Hz]
Sets the center frequency of Band 2
Q
c
Sets the bandwidth of Band 2
Gain [dB]
Sets the gain of Band 2
[E] Band3 Cutoff [Hz]
Sets the center frequency for Band 3
Q
d
Sets the bandwidth of Band 3
Gain [dB]
Sets the gain of Band 3
[E] Band4 Cutoff [Hz]
Sets the center frequency for Band 4
Q
e
Sets the bandwidth of Band 4
Gain [dB]
Sets the gain of Band 4
[P] LFO Frequency [Hz]
Sets the LFO speed
f
LFO Waveform
Selects LFO Waveform
[P] Manual
g
Sets the frequency to which the effect is applied
[P] Depth
Sets the depth of LFO modulation
h
Resonance
Sets the resonance amount
[P] Phaser Wet/Dry
Sets the phaser effect balance
i
Output Mode
Selects the phaser output mode
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 1
Src
j
Table , "Selects the modulation source of the effect balance," on page 1
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 1
Effects 20-37
Mono – Mono Chain
Wet / Dry
Phaser
Phaser
Normal
+
Output Mode
–
Wet Invert
Resonance
Phaser Wet / Dry
Wet / Dry
LFO: Tri / Sine
0...100
20...1.00kHz
0.5...10.0
☞
Fx:006
–18...+18dB
50...5.00kHz
0.5...10.0
☞
Fx:006
–18...+18dB
300...10.00kHz
0.5...10.0
☞
Fx:006
–18...+18dB
500...20.00kHz
0.5...10.0
☞
Fx:006
–18...+18dB
0.02...20.00Hz
Triangle, Sine
0...100
0...100
–100...+100
☞
Fx:023
–Wet...–2:98, Dry, 2:98...Wet
☞
Fx:010, 023
Normal, Wet Invert
☞
Fx:060
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100