Korg PA 80 User Manual page 230

20-12 Effects
Pitch/Phase Mod.
017: Harm.Chorus
(Stereo Harmonic Chorus)
This effect applies chorus only to higher frequencies. This
can be used to apply a chorus effect to a bass sound without
making the sound thinner. You can also use this chorus block
with feedback as a flanger.
Stereo In - Stereo Out
Left
Chorus/Flanger
High/Low Split Point
Chorus/Flanger
Right
LFO: Tri / Sine
LFO Waveform
a
Selects LFO Waveform
LFO Phase [degree]
b
Sets the LFO phase difference between the left and right
LFO Frequency [Hz]
Sets the LFO speed
Src
c
Selects the modulation source of LFO speed
Amt
Sets the modulation amount of LFO speed
BPM/MIDI Sync
Switches between using the frequency of the LFO speed and using the
tempo and notes
BPM
Selects MIDI Clock and assigns tempo
d
Base Note
Selects the type of notes that specify the LFO speed
Times
Sets the number of notes that specify the LFO speed
Pre Delay [msec]
e
Sets the delay time from the original sound
Depth
Sets the depth of LFO modulation
Src
f
Selects the modulation source of the LFO modulation depth
Amt
Sets the modulation amount of the LFO modulation depth
High/Low Split Point
g
Sets the frequency split point between the low and high range
Feedback
Sets the feed back amount of the chorus block
h
High Damp [%]
Sets the high range damping amount of the chorus block
Low Level
Sets the low range output level
i
High Level
Sets the high range (chorus) output level
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 1
Src
j
Table , "Selects the modulation source of the effect balance," on page 1
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 1
g: High/Low Split Point
This parameter sets the frequency that splits the high and
low range. Only the high range will be sent to the chorus
block.
Low Level Wet / Dry
High Level
High Damp
Feedback
High Damp
High Level
Low Level
Wet / Dry
LFO Phase
Triangle, Sine
–180...+180
☞
Fx:010
0.02...20.00Hz
☞
Fx:009,
Off...Tempo
–20.00...+20.00Hz
Off, On
☞
Fx:009,
MIDI, 40...240
☞
☞
Fx:009
x1...x16
☞
Fx:009
0.0...50.0msec
Off...Tempo
–100...+100
1...100
☞
–100...+100
0...100%
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
h: Feedback
Sets the feedback amount of the chorus block. Increasing
the feedback will allow you to use the effect as a flanger.
018: MTap Ch/Dly
(Multitap Chorus/Delay)
This effect has four chorus blocks with a different LFO phase.
You can create a complex stereo image by setting each block's
delay time, depth, output level, and pan individually. You can
also fix some of the chorus blocks to combine the chorus and
delay effects.
Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
Left
Feedback
+
Right
LFO: Triangle
LFO Frequency [Hz]
a
Sets the LFO speed
Tap1(000) [msec]
Sets the Tap1 (LFO phase=0 degrees) delay time
Depth
Sets the Tap1 chorus depth
b
Level
Sets the Tap1 output level
Fx:009
Pan
Sets the Tap1 stereo image
Tap2(180) [msec]
Sets the Tap2 (LFO phase=180 degrees) delay time
Depth
Sets the Tap2 chorus depth
c
Level
Sets the Tap2 output level
0...100
Pan
Sets the Tap2 stereo image
Tap3(090) [msec]
Sets the Tap3 (LFO phase=90 degrees) delay time
Depth
Sets the Tap3 chorus depth
d
Level
Sets the Tap3 output level
☞
Pan
Sets the Tap3 stereo image
Tap4(270) [msec]
Sets the Tap4 (LFO phase=270 degrees) delay time
0...100
Depth
Sets the Tap4 chorus depth
0...100
e
Level
Sets the Tap4 output level
Pan
Sets the Tap4 stereo image
Tap1 Feedback
Sets the Tap1 feedback amount
Src
f
Selects the modulation source of Tap1 feedback amount and effect balance
Amt
Sets the Tap1 feedback amount and modulation amount
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 1
g
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 1
Wet / Dry
Tap1 Delay
Level
Pan
Tap2 Delay
Level
Pan
Tap3 Delay
Level
Pan
Tap4 Delay
Level
Pan
0 [degree]
Wet / Dry
180 [degree]
90 [degree]
270 [degree]
0.02...13.00Hz
0...570msec
L6...L1, C, R1...R6
0...570msec
L6...L1, C, R1...R6
0...570msec
L6...L1, C, R1...R6
0...570msec
L6...L1, C, R1...R6
–100...+100
Off...Tempo
–100...+100
Dry, 1:99...99:1, Wet
–100...+100
0...30
0...30
0...30
0...30
0...30
0...30
0...30
0...30