Table of Contents
Advertisement
SERVICE SCHEDULE
Service schedule
35.1
Check that the electrical equipment is functioning correctly.
Read out the fault memory using the KTM diagnostics tool.
Change the engine oil and filter, clean the oil screens. (
Check the front brake linings. (
Check the rear brake linings. (
Check the brake discs. (
p. 65)
Check the brake lines for damage and leakage.
Check the rear brake fluid level. (
Check the free travel of the foot brake lever. (
Lubricate the linkage of the rear wheel suspension.
Check that the shock absorber and fork are leak tight. If necessary and depending on use, ser-
vice the fork and shock absorber.
Check the swingarm bearing.
Check the wheel bearing for play.
Check the tire condition. (
Check the tire air pressure. (
Check the spoke tension. (
Check for rim run-out.
Check the chain, rear sprocket and engine sprocket. (
Check the chain tension. (
Grease all moving parts (e.g. side stand, hand lever, chain, ...) and check for smooth opera-
tion.
Clean the dust boots of the fork legs. (
Check the front brake fluid level. (
Bleed the fork legs. (
p. 12)
Check the steering head bearing play. (
Change the spark plug.
Check the valve clearance.
Check all hoses (e.g. fuel, cooling, bleeder, drainage, etc.) and bellows for cracking, leaks,
and correct routing.
Check the antifreeze and coolant level. (
Check the cables for damage and routing without sharp bends.
Check that the throttle cables are undamaged, routed without sharp bends and set correctly.
Replace the fuel evaporation container. (only applies to spare part number 75015001000)
(690 Enduro USA)
Change the air filter. Clean the air filter box.
Check/rectify the fluid level of the hydraulic clutch. (
Check the screws and nuts for tightness.
Change the coolant.
Change the front brake fluid. (
Change the rear brake fluid. (
Check the clutch.
Check the headlight setting. (
Check that the radiator fan is functioning properly.
Final check: Check the vehicle for roadworthiness and take a test ride.
Read out the fault memory using the KTM diagnostics tool after a test ride.
Make the service entry in KTM DEALER.NET and in the service record.
K10N: Once after 1,000 km (621.4 mi)
K50A: Every 5,000 km (3,107 mi) or annually
K100A: Every 10,000 km (6,214 mi) or every 2 years
K300A: Every 30,000 km (18,641 mi) or every 4 years
p. 77)
p. 81)
p. 84)
p. 83)
p. 64)
p. 64)
p. 70)
p. 68)
p. 67)
p. 13)
p. 79)
p. 29)
p. 155)
p. 153)
p. 80)
p. 85)
p. 89)
p. 159)
K10N
K50A
K100A
K300A
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
187
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Advertisement
Table of Contents
