Respironics REMstar Pro M Series User Manual page 45

a a: EmC I
ppEndIx
g m
UIdanCE and anUfaCtUrEr
electromagnetic environment specified below. The user of this device should make sure it is used in such an environment.
E t
mIssIons Est
RF emissions
CISPR 11
RF emissions
CISPR 11
Harmonic emissions
IEC 61000-3-2
Voltage fluctuations/Flicker emissions
IEC 61000-3-3
g m
UIdanCE and anUfaCtUrEr
electromagnetic environment specified below. The user of this device should make sure it is used in such an environment.
I t
mmUnIty Est
Electrostatic
Discharge (ESD)
IEC 61000-4-2
Electrical fast
Transient/burst
IEC 61000-4-4
Surge
IEC 61000-4-5
Voltage dips, short interrup-
tions and voltage variations on
power supply input lines
IEC 61000-4-11
Power frequency (50/60 Hz)
magnetic field
IEC 61000-4-8
NOTE: U is the a.c. mains voltage prior to application of the test level.
T
rEm p m s
star ro ErIEs
nformatIon
' d - E
s EClaratIon
C
omplIanCE
Group 1
Class B
Class A
Complies
' d - E
s EClaratIon
IEC 60601 t
Est
l
EvEl
±6 kV contact
±8 kV air
±2 kV for power supply lines
±1 kV for input-output lines
±1 kV differential mode
±2 kV common mode
<5% U
T
(>95% dip in U ) for
T
0.5 cycle
40% U
T
(60% dip in U ) for
T
5 cycles
70% U (30% dip in
T
U ) for 25 cycles
T
<5% U (>95% dip in U ) for
T T
5 sec
3 A/m
U m
sEr anUal
E
lECtromagnEtIC mIssIons
E
lECtromagnEtIC
The device uses RF energy only for its internal function. Therefore, its RF emissions
are very low and are not likely to cause any interference in nearby electronic equip-
ment.
The device is suitable for use in all establishments, including domestic establish-
ments and those directly connected to the public low-voltage power supply
network.
I
lECtromagnEtIC mmUnIty
C l
omplIanCE EvEl
±6 kV contact
±8 kV air
±2 kV for supply mains
±1 kV for input/output lines
±1 kV differential mode
±2 kV for common mode
<5% U
T
(>95% dip in U ) for
T
0.5 cycle
40% U
T
(60% dip in U ) for 5 cycles
T
70% U (30% dip in U ) for 25
T T
cycles
<5% U (>95% dip in U ) for
T T
5 sec
3 A/m
–
This device is intended for use in the
E - g
nvIronmEnt UIdanCE
–
This device is intended for use in the
E E
lECtromagnEtIC nvIronmEnt
g
UIdanCE
Floors should be wood, concrete or ceramic
tile. If floors are covered with synthetic
material, the relative humidity should be at
least 30%.
Mains power quality should be that of a typi-
cal home or hospital environment.
Mains power quality should be that of a typi-
cal home or hospital environment.
Mains power quality should be that of a
typical home or hospital environment. If the
user of the device requires continued opera-
tion during power mains interruptions, it is
recommended that the device be powered
from an uninterruptible power supply or a
battery.
Power frequency magnetic fields should be
at levels characteristic of a typical location in
a typical hospital or home environment.
-
A-1