Jeep 1996 Grand Cherokee Service Manual page 586

ZJ
8W-39 VEHICLE THEFT SECURITY SYSTEM
DESCRIPTION AND OPERATION
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . 1
VEHICLE THEFT SECURITY SYSTEM
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
DESCRIPTION AND OPERATION
INTRODUCTION
The Body Control Module (BCM) operates the
Vehicle Theft Security System (VTSS). The BCM
monitors the vehicle doors, hood, liftglass in the lift-
gate, liftgate, and ignition for unauthorized opera-
tion.
When the BCM detects unauthorized operation, it
operates the horn repeatedly for three minutes and
flashes the headlamps and tail lamps for 15 minutes.
Also, the engine will not operate until the VTSS is
disarmed.
The vehicle operator can activate the alarm by
pushing the panic button on the Remote Keyless
Entry (RKE) transmitter. When the operator pushes
the panic button, the radio frequency receiver in the
Passenger Door Module (PDM) receives the PANIC
signal and broadcasts a message on the CCD bus.
When the BCM sees the PANIC message on the CCD
bus, it operates the horn repeatedly, turns on the
interior lights, and flashes the headlamps and tail
lamps. The BCM activates the panic alarm for three
minutes unless the operator starts the vehicle and
drives at a speed above 15 MPH or pushes the panic
button on the RKE transmitter a second time.
When the ignition switch is in the START or RUN
position, it connects circuit A1 from fuse 8 in the
PDC to circuit A21. Circuit A21 powers circuit F99
through PDC fuse 18. Circuit F99 feeds the BCM.
In the ACCESSORY or RUN position, the ignition
switch connects circuit A1 to circuit A31. Circuit A31
powers circuit V23 through fuse 3 in the junction
block. Circuit V23 feeds the BCM.
VEHICLE THEFT SECURITY SYSTEM OPERATION
Each door, the liftgate, hood, and the liftglass in
the liftgate have an ajar switch that connects to the
Body Control Module (BCM). The ajar switches are
normally open when the doors, liftgate, liftglass and
hood are closed. When one of them open, its ajar
switch closes and connects the BCM to ground. In
response, if the Vehicle Theft Security System is
8W - 39 VEHICLE THEFT SECURITY SYSTEM
page
INDEX
SCHEMATICS AND DIAGRAMS
WIRING DIAGRAM INDEX . . . . . . . . . . . . . . . . . . 2
armed, the BCM starts the alarm. Refer to the Intro-
duction in this section for alarm information.
The BCM receives the ajar switch signals on the
following circuits.
• Circuit G75 provides the left front door ajar
switch signal
• Circuit G74 provides the right front door ajar
switch signal
• Circuit G77 provides the left rear door ajar
switch signal
• Circuit G76 provides the right rear door ajar
switch signal
• Circuit G78 provides the liftgate ajar and lift-
glass ajar signals
SYSTEM ARMING
The system alarm sets after the operator uses the
power door locks or Remote Keyless Entry (RKE)
transmitter to lock the doors and liftgate. After all
doors and the liftgate are locked and closed, the BCM
illuminates a red Light Emitting Diode (LED) (VTSS
indicator light) on circuit G69. The red LED is
located on the top of the instrument panel. The LED
flashes rapidly signalling the system is arming. It
flashes at slower rate after approximately 15 sec-
onds, indicating the BCM has set the VTSS.
SYSTEM DISARMING
The operator can disarm the system by unlocking a
front door or the liftgate with the key or the RKE
transmitter. The BCM monitors the lock cylinder
switch in each front door and the liftgate lock cylin-
der switches on circuit G71.
HORNS
When the BCM activates the horns, it energizes
the horn relay by providing a ground path for the
relay coil on circuit X4. Circuit F31 from fuse 6 in
the Power Distribution Center (PDC) powers the coil
and contact sides of the relay.
When the horn relay energize, its contact close and
connect circuit F31 to circuit X2. Circuit X2 feeds the
horns. Circuit Z1 provides ground for the horns.
8W - 39 - 1
page