Page 1
User Guide 2013 Grand Cherokee Includes SRT8...
Page 2
Warranty and Roadside Assistance (new vehicles purchased in the U.S.) or Roadside Assistance (new vehicles purchased in Canada) in electronic format. We hope you find it useful. Replacement DVD kits may be purchased by visiting www.techauthority.com. Jeep is a registered ®...
TABLE OF CONTENTS INTRODUCTION/WELCOME Bluetooth ® STREAMING AUDIO ..73 Uconnect Phone ....74 ® WELCOME FROM CHRYSLER Uconnect ® VOICE COMMAND ..77 GROUP LLC .
Page 4
TABLE OF CONTENTS CONSUMER ASSISTANCE MOPAR ACCESSORIES CHRYSLER GROUP LLC AUTHENTIC ACCESSORIES BY CUSTOMER CENTER ... 133 MOPAR ® ....135 CHRYSLER CANADA INC.
INTRODUCTION/WELCOME WELCOME FROM CHRYSLER GROUP LLC Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. Your new Chrysler Group LLC vehicle has characteristics to enhance the driver's control under some driving conditions.
Page 6
INTRODUCTION/WELCOME VEHICLES SOLD IN CANADA With respect to any vehicles sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution. WARNING! • Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury.
Page 7
If your symptoms persist, please see an authorized dealer. CHRYSLER, DODGE, JEEP, RAM TRUCK, SRT, ATF+4, MOPAR and Uconnect are registered trademarks of Chrysler Group LLC.
CONTROLS AT A GLANCE INSTRUMENT CLUSTER Warning Lights - Low Fuel Warning Light - Charging System Light** - Oil Pressure Warning Light** - Engine Temperature Warning Light - Transmission Temperature Warning Light - Anti-Lock Brake (ABS) Light** - Air Bag Warning Light** - Electronic Throttle Control (ETC) Light - Tire Pressure Monitoring System (TPMS) Light - Seat Belt Reminder Light...
Page 11
CONTROLS AT A GLANCE Indicators - Turn Signal Indicators - Adaptive Cruise Control (ACC) SET Indicator* - High Beam Indicator - Hill Descent Control Indicator* - Front Fog Light Indicator* - Park/Headlight ON Indicator* - Vehicle Security Indicator* - Electronic Stability Control (ESC) Off Indicator* - TOW/HAUL Indicator* - Windshield Washer Fluid Low...
GETTING STARTED KEY FOB Locking And Unlocking The Doors/Liftgate • Press the LOCK button once to lock all the doors and the liftgate. Press the UNLOCK button once to unlock the driver’s door only and twice within five seconds to unlock all the doors and liftgate.
Page 13
GETTING STARTED • In case the Key Fob battery is dead, use the emergency key to open the door. If the vehicle is equipped with Keyless Enter-N-Go™, remove the ENGINE START/STOP button by inserting the metal part of the emergency key under the chrome bezel at the 6 o’clock position and gently pry the button loose.
GETTING STARTED WARNING! • Never use the PARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • When leaving the vehicle, always remove the key fob from the ignition and lock your vehicle.
GETTING STARTED KEYLESS ENTER-N-GO™ • The Keyless Enter-N-Go™ system is an enhancement to the vehicle's Key Fob. This feature allows you to lock and unlock the vehicle's door(s) and liftgate without having to press the Key Fob lock or unlock buttons, as well as starting and stopping the vehicle with the press of a button.
Page 16
GETTING STARTED • If “Unlock All Doors 1st Press” is programmed all doors and liftgate will unlock when you press the liftgate button. If “Unlock Driver Door 1st Press” is pro- grammed only the liftgate will unlock when you press the liftgate button. To select between “Unlock Driver Door 1st Press”...
Page 17
GETTING STARTED Removing The Button • The ENGINE START/STOP button can be removed from the ignition switch for Key Fob use. • Insert the metal part of the emergency key under the chrome bezel at the 6 o’clock position and gently pry the button loose.
GETTING STARTED Accessory Positions with Engine Off NOTE: The following functions are with the driver’s foot OFF the Brake Pedal (Transmission in PARK or NEUTRAL Position). Starting With The Ignition Switch In The OFF Position: • Press the ENGINE START/STOP button once to change the ignition switch to the ACC position.
GETTING STARTED To Disarm • Keyless Enter-N-Go™ button installed: Press the Key Fob UNLOCK button or with one of the Key Fobs located outside the vehicle and within 5 ft (1.5 m) of the driver's and passenger front door handles, grab the Keyless Enter-N-Go™ door handle and enter the vehicle, then press the Keyless Enter-N-Go™...
GETTING STARTED SUPPLEMENTAL RESTRAINT SYSTEM (SRS) — AIR BAGS • This vehicle has Advanced Front Air Bags for both the driver and right front passenger as a supplement to the seat belt restraint system. The Advanced Front Air Bags will not deploy in every type of collision. •...
GETTING STARTED CHILD RESTRAINTS • Children 12 years and under should ride properly buckled up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front. •...
Page 22
GETTING STARTED • The tether strap should be attached to the tether anchor on the rear of the seatback (behind the gap panel) using the most direct path. DO NOT USE the cargo tie down loops located on the load floor. •...
GETTING STARTED FRONT SEATS Power Seats • The recline switch, located on the out- board side of the seat, controls seat- back adjustment. • The power seat switch controls forward/ back, up/down and tilt adjustment. Power Lumbar • Push the switch forward to increase the lumbar support.
Page 24
GETTING STARTED • To program a Key Fob to the memory position, place the ignition switch in the LOCK position and remove the Key Fob, press and release the LOCK button on the Key Fob to be programmed within 5 seconds of pressing button 1 or 2. •...
Page 25
GETTING STARTED Fold-Flat Front Passenger Seat • The front passenger seat can be folded flat to allow for extended cargo space. Pull up on the recliner lever to fold down the seatback. CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls.
GETTING STARTED REAR SEATS 60/40 Split Rear Seat To Lower Rear Seatback • With the front seats fully upright and positioned forward, pull upward on the release lever and fold the rear seatback down. To Raise Rear Seatback • Raise the rear seatback and lock it into place.
Page 27
GETTING STARTED Front Ventilated Seats • Located in the seat cushion and seatback are small fans that draw the air from the passenger compartment and blow air through fine perforations in the seat cover to help keep the driver and front passenger cooler in higher ambient temperatures. •...
GETTING STARTED HEATED STEERING WHEEL • The steering wheel contains a heating element that heats the steering wheel to one temperature setting. • The heated steering wheel switch is located on the center instrument panel below the climate controls. • Press the switch once to turn the heat- ing element On.
Page 29
GETTING STARTED Power - Tilt/Telescoping Steering Column • The power tilt/telescoping steering control is located below the turn signal/wiper/washer/high beam lever on the steering column. • To tilt the steering column, move the power tilt/telescoping control up or down as desired. To lengthen or shorten the steering column, pull the control toward you or push the control away from you as desired.
OPERATING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS • A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. • Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.
OPERATING YOUR VEHICLE CAUTION! Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. HEADLIGHT SWITCH Automatic Headlights/Parking Lights/Headlights • Rotate the headlight switch, located on the instrument panel to the left of the steering wheel, to the first detent for parking lights and to the sec- ond detent for headlights...
OPERATING YOUR VEHICLE TURN SIGNAL/WIPER/WASHER/HIGH BEAM LEVER Turn Signal/Lane Change Assist • Tap the lever up or down once and the turn signal (right or left) will flash three times and automatically turn off. Front Wipers Intermittent, Low And High Operation •...
OPERATING YOUR VEHICLE Rear Wiper Rear Wiper Operation • Rotate the center portion of the lever forward to the first detent for intermittent operation and to the second detent for rear wiper operation. Rear Washer Operation • Rotate the center portion of the lever past the second detent to activate the rear washer.
Page 34
OPERATING YOUR VEHICLE • With the Speed Control on, push and release the SET – button to set a desired speed. Accel/Decel • Once a speed is set, pushing the RES + button once or the SET – button once will increase or decrease the set speed approximately 1 mph (2 km/h).
Page 35
OPERATING YOUR VEHICLE Mode (ACC Only) • If desired, the Adaptive Cruise Control mode can be turned off and the system can be operated as a standard (fixed speed) Cruise Control. When in the standard (fixed speed) Cruise Control mode the distance setting feature will be disabled and the system will maintain the speed you set.
Page 36
OPERATING YOUR VEHICLE Near • Changing the FCW status to the “Near” setting, allows the system to warn you of a potential frontal collision when you are much closer. • This setting provides less reaction time than the “Far” setting, which allows for a more dynamic driving experience.
Page 37
OPERATING YOUR VEHICLE WARNING! • Leaving the Electronic or Adaptive Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have a collision. Always leave the Electronic or Adaptive Speed Control system off when you are not using it.
OPERATING YOUR VEHICLE ELECTRONIC RANGE SELECTION (ERS) • Electronic Range Select (ERS) allows you to limit the highest available trans- mission gear, and can be activated during any driving condition. When towing a trailer or operating the vehicle in off-road conditions, using ERS shift control will help you maximize both performance and engine braking.
OPERATING YOUR VEHICLE AUTOMATIC TEMPERATURE CONTROLS (ATC) Automatic Operation • Press the AUTO button. • Select the desired temperature by pressing the Temperature Control buttons. • The system will maintain the set temperature automatically. Air Conditioning (A/C) • If the air conditioning button is pressed while in AUTO mode, the system will exit AUTO mode and stay in A/C.
OPERATING YOUR VEHICLE PARKSENSE® REAR PARK ASSIST • The four ParkSense ® sensors, located in the rear fascia/bumper, monitor the area behind the vehicle that is within the sensors’ field of view. • When an object is detected within two meters behind the rear bumper while the vehicle is in REVERSE, a warning will display in the Electronic Vehicle Information Center (EVIC) and a chime will sound (when Sound and Display is selected from the Customer Programmable Features section of the EVIC).
OPERATING YOUR VEHICLE BLIND SPOT MONITORING • The Blind Spot Monitoring (BSM) system uses two radar-based sensors, located inside the rear bumper fascia, to detect Highway licensable vehicles (automobiles, trucks, motorcycles etc.) that enter the blind spot zones from the rear/front/side of the vehicle.
OPERATING YOUR VEHICLE POWER SUNROOF Manual Open/Close • Press and hold the switch rearward to open or forward to close the sunroof. Any release of the switch will stop the movement, and the sunroof will remain in a partially open or closed position until the switch is pressed again. CommandView®...
OPERATING YOUR VEHICLE Manual Open/Close • Press and hold the switch rearward to open or forward to close the power shade. Any release of the switch will stop the movement, and the power shade will remain in a partially open or closed position until the switch is pressed again. Pinch Protection Feature •...
ELECTRONICS Uconnect® 130 NOTE: Your radio has many features that add to the comfort and convenience of you and your passengers. Some of these radio features should not be used when driving because they take your eyes from the road or your attention from driving. Clock Setting •...
Page 47
ELECTRONICS Radio Operation Seek Up/Down Buttons • Press to seek through radio stations in AM or FM bands. • Hold either button to bypass stations without stopping. Store Radio Presets • Press the “SET/RND” button once and SET 1 will show in the display. Then select button (1–6).
ELECTRONICS Uconnect® 130 WITH SiriusXM SATELLITE RADIO NOTE: • Your radio may not be equipped with the Uconnect ® Voice Command and Uconnect ® Phone features. To determine if your radio has these features, press the Voice Command button on the radio. You will hear a voice prompt if you have the feature, or see a message on the radio stating “Uconnect Phone not available”...
Page 49
ELECTRONICS Equalizer, Balance And Fade • Press the “TUNE/SCROLL” control knob and BASS, MID, TREBLE, BALANCE and FADE will display. Rotate the “TUNE/SCROLL” control knob to select the desired setting. Radio Operation Seek Up/Down Buttons • Press to seek through radio stations in AM, FM, or SAT bands. •...
Page 50
ELECTRONICS CD/DISC Operation Seek Up/Down Buttons • Press to seek through CD tracks. • Hold either button to bypass tracks without stopping. SET/RND Button (Random Play) • Press this button while the CD is playing to activate Random Play. • This feature plays the selections on the CD in random order to provide an interesting change of pace.
ELECTRONICS Uconnect® 430/430N NOTE: • Your radio may not be equipped with the Uconnect ® Voice Command and Uconnect ® Phone features. To determine if your radio has these features, press the Voice Command button on the radio. You will hear a voice prompt if you have the feature, or see a message on the radio stating “Uconnect Phone not available”...
Page 52
ELECTRONICS Menu • Press the “MENU” hard-key to access the System Setup menu and the My Files menu. • Press the “MENU” hard-key in an active mode (SAT, CD, AUX, etc.) in order to change mode specific settings. Equalizer, Balance And Fade Audio Control Menu •...
Page 53
ELECTRONICS Radio Operation • To access Radio Mode, touch the “RADIO” hard-key on the left side of the faceplate, then touch the “AM,” “FM” or “SAT” soft-key at the top of the screen to select the band. Seek Up/Seek Down •...
Page 54
ELECTRONICS CD/DVD Disc Operation • Press the “MEDIA” hard key to display the media source tabs at the top of the screen. Select the source by touching the “HDD,” “DISC,” or “AUX” media source soft-key tab. NOTE: Your Touch-Screen Radio will usually automatically switch to the appropriate mode when something is first connected or inserted into the system.
Page 55
ELECTRONICS Audio Jack Operation • The AUX/Audio Jack provides a means to connect a portable audio device, such as an MP3 player or an iPod ® , to the vehicles sound system. This requires the use of a 3.5 mm stereo audio patch cable. •...
Page 56
ELECTRONICS Copying Music From USB • The USB port on the radio face plate allows you to copy files to your hard drive. To access, lift up on the cover. • Insert a USB device (e.g. thumb drive or memory stick), then select “MY MUSIC soft-key.”...
Page 57
ELECTRONICS Playing Music From The HDD • Press the “MEDIA” hard key to display the media source tabs at the top of the screen. Touch the “HDD” soft-key tab. Touch the desired track soft-key to play or touch the “SEARCH/BROWSE” soft-key to search by artist, by album, by song, by genre, from a folder, or from Favorites.
Page 58
ELECTRONICS 4. While the Navigation system is speaking, use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level. Please note the volume setting for Navigation Voice Prompt is different than the audio system. NOTE: For your own safety and the safety of others, it is not possible to use certain features while the vehicle is in motion.
Page 59
ELECTRONICS Following Your Route • Your route is marked with a magenta line on the map. If you depart from the original route, your route is recalculated. A speed limit icon could appear as you travel on major roadways. Adding A Via Point •...
ELECTRONICS Acquiring Satellites • The GPS Satellite strength bars indicate the strength of your satellite reception. • Acquiring satellite signals can take a few minutes. When at least one of the bars is green, your device has acquired satellite signals. •...
Page 61
ELECTRONICS Menu • Press the “MENU” hard-key to access the System Setup menu and the My Files menu. • Press the “MENU” hard-key in an active mode (SAT, CD, AUX, etc.) in order to change mode specific settings. Equalizer, Balance And Fade Audio Control Menu •...
Page 62
ELECTRONICS Radio Operation • To access Radio Mode, touch the “RADIO/MEDIA” hard-key on the left side of the faceplate repeatedly until AM/FM/SAT appears at the top of the screen, then touch the “AM,” “FM” or “SAT” soft-key to select the band. Seek Up/Seek Down •...
Page 63
ELECTRONICS CD/DVD Disc Operation • Press the “RADIO/MEDIA” hard key until the media source tabs are displayed at the top of the screen. Select the source by touching the “HDD,” “DISC,” or “AUX” media source soft-key tab. NOTE: Your Touch-Screen Radio will usually automatically switch to the appropriate mode when something is first connected or inserted into the system.
Page 64
ELECTRONICS Audio Jack Operation • The AUX/Audio Jack provides a means to connect a portable audio device, such as an MP3 player or an iPod ® , to the vehicles sound system. This requires the use of a 3.5 mm stereo audio patch cable. •...
Page 65
ELECTRONICS • Touch the “Add Music Files to HDD” soft-key, then touch the “From Disc” soft-key in the next screen to start the process. NOTE: • You might need to select the folder or title depending on the CD, then press “Done”...
Page 66
ELECTRONICS Display A Picture On The Radio Screen • Once the import is complete, the pictures will then be available in the “MY PICTURES” screen. • Press the “MENU” hard-key to access the Settings Menu, then touch the “My Files” soft-key and then touch the “My Pictures”...
Page 67
ELECTRONICS NAVIGATION • Your navigation system receives GPS signals from up to 16 satellites to dis- play the position of your vehicle. Map and database information is supplied through a hard disk drive. • Touch the “NAV” hard-key on the radio face plate to access the Navigation system and the NAV –...
Page 68
ELECTRONICS Main Navigation Menu Finding Points Of Interest • From the NAV main menu, touch the “Points of Interest” soft-key. • Select a Category and then a subcategory, if necessary. • Select your destination and touch “GO.” Finding A Place By Entering The Street Address •...
Page 69
ELECTRONICS Entering Your Home Location • Press the “NAV” hard-key on the right side of the radio. • From the Nav – Main Menu, touch “Guide Me Home” to enter your home address. If no home address has been set, touch “YES” to access the Enter Home Address menu.
Page 70
ELECTRONICS Route Guidance • After starting route guidance, the system calculates the route and announces: “Follow the arrows on the display.” You will receive navigation recommendations by voice messages and screen displays. Route Options • After pressing the “OPTIONS” soft-key in the Route Guidance Menu, the following information is displayed: •...
ELECTRONICS SiriusXM SATELLITE RADIO/TRAVEL LINK • SiriusXM Travel Link requires a subscription, sold separately after the 1 year trial subscription included with your vehicle purchase. • SiriusXM Travel Link is only available in the United States. • The following describes features that are available when in SiriusXM Satellite Radio mode.
Page 72
ELECTRONICS • You will see a favorite star indicator in the upper right side of the screen below the SAT soft-key and a pop up will alert you that a favorite song or artist is currently playing on one of the SiriusXM satellite radio channels. NOTE: Refer to your Uconnect ®...
Page 73
ELECTRONICS Replay Option Option Description Fast Forward/FW Forwards the content, and works similarly to Rewind/RW. However, Fast Forward/FW can only be used when content has been previously rewound. Replay Time Displays the amount of time in the upper center of the screen by which your content lags the Live channel.
ELECTRONICS STEERING WHEEL AUDIO CONTROLS • The steering wheel audio controls are located on the rear surface of the steer- ing wheel. Right Switch • Press the switch up or down to in- crease or decrease the volume. • Press the button in the center to change modes AM/FM/CD/SAT.
ELECTRONICS • Non-Touch-Screen Radios: To hear audio from devices connected to the USB port, press the “AUX” button on the radio faceplate • Touch-Screen Radios: To hear audio from devices connected to the USB port, press the “MEDIA” hard-key, then touch the “AUX” or “iPod ®...
ELECTRONICS Uconnect® Phone • To determine if your vehicle is equipped with Uconnect ® Phone, press the “Uconnect ® Phone” button . If your vehicle has this feature, you will hear a voice prompt. If not, you will see a message on the radio “Uconnect phone not available”. •...
Page 77
ELECTRONICS • (After the BEEP), say “device pairing”. • (After the BEEP), say “pair a device”. • Follow the audible prompts. • You will be asked to say a four-digit Personal Identification Number (PIN), which you will later need to enter into your mobile phone.
Page 78
ELECTRONICS • Only the mobile phone’s phonebook is downloaded. The SIM card phonebook is not part of the Mobile phonebook. • This downloaded phonebook cannot be edited or deleted on the Uconnect ® Phone. These can only be edited on the mobile phone. The changes are transferred and updated to Uconnect Phone on the next phone connection.
ELECTRONICS Uconnect® VOICE COMMAND Voice Command Operation • The Uconnect Voice Command system allows you to control your AM, FM radio, ® satellite radio, disc player, HDD, Uconnect Phone, a memo recorder, and supported ® portable media devices. • When you press the “Voice Command” button located on the radio faceplate or steering wheel, you will hear a beep.
Page 80
ELECTRONICS SiriusXM Satellite “Channel Number” (to change the channel by its spoken number) Radio Mode “Next Channel” (to select the next channel) “Previous Channel” (to select the previous channel) “List Channel” (to hear a list of available channels) "Channel Name" (to change the channel by its spoken name) “Select Name”...
ELECTRONICS NOTE: To access the tutorial, press the “Voice Command” button . After the BEEP, say “tutorial”. Press any hard-key/button or touch the display (Touch-Screen radio) to cancel the tutorial. WARNING! Any voice commanded system should be used only in safe driving conditions following applicable laws regarding phone use.
ELECTRONICS Operation Of The Remote • The remote control operates similarly to any DVD remote you have used before and allows the rear seat passengers to change stations, tracks, discs and audio/video modes. • The remote control is designed to control either channel by using the selector switch located on the right side of the remote.
ELECTRONICS Compass Calibration • This compass is self-calibrating, which eliminates the need to set the compass manually. When the vehicle is new, the compass may appear erratic and the EVIC will display “CAL” until the compass is calibrated. • You may also calibrate the compass by completing one or more 360 degree turns (in an area free from large metal or metallic objects) until the “CAL”...
ELECTRONICS UNIVERSAL GARAGE DOOR OPENER (HomeLink®) • HomeLink ® replaces up to three hand- held transmitters that operate devices such as garage door openers, motor- ized gates, lighting or home security systems. The HomeLink unit is pow- ® ered by your vehicles 12 Volt battery. •...
Page 85
ELECTRONICS • Simultaneously press and hold both the HomeLink ® button you want to program and the hand-held transmitter button. • Continue to hold both buttons and observe the indicator light. The HomeLink ® indicator will flash slowly and then rapidly after HomeLink has received the ®...
ELECTRONICS Using HomeLink® • To operate, press and release the programmed HomeLink ® button. Activation will now occur for the programmed device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.,). The hand-held transmitter of the device may also be used at any time.
ELECTRONICS NOTE: The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet, the inverter should automatically reset.
Page 88
ELECTRONICS NOTE: • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded, the fuse protecting the system will need to be replaced. • Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse.
OFF-ROAD CAPABILITIES QUADRA-TRAC I® FOUR-WHEEL DRIVE Quadra-Trac I® Operating Instructions/Precautions - 3.6L Only • The Quadra-Trac I is a single-speed (HI range only) transfer case, which provides ® convenient full-time four-wheel drive. No driver interaction is required. The Brake Traction Control (BTC) System, which combines standard ABS and Traction Control, provides resistance to any wheel that is slipping to allow additional torque transfer to wheels with traction.
OFF-ROAD CAPABILITIES Shifting Procedures 4WD HI To 4WD LOW • With the vehicle at speeds of 0 to 3 mph (0 to 5 km/h), the ignition switch in the ON/RUN position or the engine running, shift the transmission into NEUTRAL, and press the “4WD LOW”...
UTILITY TOW/HAUL MODE • When driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting occurs, press the TOW/HAUL switch to select TOW/HAUL mode. This will improve performance and reduce the potential for transmission overheating or failure due to excessive shifting. When operating in TOW/HAUL mode, transmission upshifts are delayed, and the transmission will automatically downshift (for engine braking) during steady braking maneuvers.
Page 93
UTILITY • Turn the ignition switch to the ON/RUN position, but do not start the engine. • Press and hold the brake pedal and shift the transmission into NEUTRAL. • Using a ballpoint pen or similar object, press and hold the recessed transfer case N (Neutral) button for four seconds, until the light next to the N symbol starts to blink, indicating shift in progress.
SRT8 AUTOSTICK® • AutoStick ® is a driver-interactive transmission feature that offers manual gear shifting to provide you with more control of the vehicle. AutoStick allows you to ® maximize engine braking, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance. •...
SRT8 SELEC-TRACK™ • Selec-Track™ combines the capabilities of the vehicle control systems, along with driver input, to provide the best performance for all terrains. • Rotate the mode control knob to select the following Selec-Track™ positions: • Sport - Dry weather, on-road cali- bration.
SRT8 SRT8 PERFORMANCE FEATURES Electronic Vehicle Information Center (EVIC) • The EVIC can be used to program the following Performance Features. Press the UP or DOWN button until Perfor- mance Features displays, then press the SELECT button. Scroll through the settings using the UP or DOWN but- tons.
SRT8 Peak G-Force • When selected, this screen displays all four G-Force values (two lateral and two longitudinal). Digital Speedometer • When selected, this screen displays vehicle speed and records top speed. WARNING! Measurement of vehicle statistics with the Performance Features is intended for off-highway or off-road use only and should not be done on any public roadways.
WHAT TO DO IN EMERGENCIES ROADSIDE ASSISTANCE • Dial toll-free 1-800-521-2779 for U.S. Residents or 1-800-363-4869 for Canadian Residents. • Provide your name, vehicle identification number, license plate number, and your location, including the telephone number from which you are calling. •...
Page 99
WHAT TO DO IN EMERGENCIES • When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly.
Page 100
WHAT TO DO IN EMERGENCIES - Malfunction Indicator Light (MIL) • Certain conditions, such as a loose or missing gas cap, poor fuel quality, etc., may illuminate the MIL after engine start. The vehicle should be serviced if the light stays on through several typical driving cycles.
Page 101
WHAT TO DO IN EMERGENCIES - Anti-Lock Brake (ABS) Light • This light monitors the Anti-Lock Brake System (ABS). • If the light is not on during starting, stays on, or turns on while driving, we recommend you drive to the nearest service center and have the vehicle serviced immediately.
WHAT TO DO IN EMERGENCIES IF YOUR ENGINE OVERHEATS • In any of the following situations, you can reduce the potential for overheating by taking the appropriate action. • On the highways — slow down. • In city traffic — while stopped, place the transmission in NEUTRAL, but do not increase engine idle speed.
Page 103
WHAT TO DO IN EMERGENCIES WARNING! • Do not exceed 50 mph (80 km/h) if the “Tire Pressure Monitoring Telltale Light” is illuminated. Vehicle handling and braking may be reduced. You could have a collision and be severely or fatally injured. •...
Page 104
WHAT TO DO IN EMERGENCIES Preparations For Jacking 1. Park the vehicle on a firm, level surface. Avoid ice or slippery surfaces. 2. Turn on the Hazard Warning flasher. 3. Set the parking brake. 4. Place the shift lever into PARK. 5.
Page 105
WHAT TO DO IN EMERGENCIES 4. For the front axle, place the jack on the body flange just behind the front tire as indicated by the triangular lift point symbol on the sill molding. Do not raise the vehicle until you are sure the jack is fully engaged.
Page 106
WHAT TO DO IN EMERGENCIES 5. For a rear tire, place the jack in the slot on the rear tie-down bracket, just forward of the rear tire (as indicated by the triangular lift point symbol on the sill molding). Do not raise the vehicle until you are sure the jack is fully engaged. 6.
Page 107
WHAT TO DO IN EMERGENCIES Road Tire Installation 1. Mount the road tire on the axle. 2. Install the remaining lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. 3. Lower the vehicle to the ground by turning the jack handle counterclockwise. 4.
Page 108
WHAT TO DO IN EMERGENCIES WARNING! • Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. •...
WHAT TO DO IN EMERGENCIES BATTERY LOCATION • The battery in your vehicle is located under the passenger's front seat. Remote battery posts are located on the right side of the engine compartment for jump-starting. JUMP-STARTING • If your vehicle has a discharged battery it can be jump-started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack.
Page 110
WHAT TO DO IN EMERGENCIES 4. Connect the opposite end of the negative (-) jumper cable to the remote negative (-) post of the vehicle with the discharged battery. 5. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged battery.
WHAT TO DO IN EMERGENCIES WARNING! • When temperatures are below the freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump-starting because the battery could rupture or explode and cause personal injury. Battery temperature must be brought above the freezing point before attempting a jump-start.
WHAT TO DO IN EMERGENCIES SHIFT LEVER OVERRIDE • If a malfunction occurs and the shift lever cannot be moved out of the PARK position, you can use the following pro- cedure to temporarily move the shift lever: • To access the shift lever override, remove the rubber cupholder liner to the right of the shift lever.
WHAT TO DO IN EMERGENCIES EVENT DATA RECORDER (EDR) • This vehicle is equipped with an Event Data Recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed.
MAINTAINING YOUR VEHICLE OPENING THE HOOD • Pull the hood release lever located below the steering wheel at the base of the instrument panel. • Reach into the opening beneath the center of the hood and move the safety latch lever while lifting the hood at the same time.
MAINTAINING YOUR VEHICLE FUEL DOOR RELEASE • The fuel door release button is located on the instrument panel below the headlight switch. • Push the button once and release to open the fuel door. Fuel Door Emergency Release • To manually open the fuel door, remove the storage bin located in the rear cargo area and pull the release cable located in the storage bin opening.
MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Non SRT8 Component Fluid, Lubricant, or Capacities Genuine Part We recommend you use MOPAR Antifreeze/Coolant ® 3.6L Engine 10 Year/ 150,000 Mile 10.4 Quarts (9.9 Liters) Formula OAT (Organic Additive Technology). We recommend you use MOPAR ®...
Page 121
MAINTAINING YOUR VEHICLE Component Fluid, Lubricant, or Capacities Genuine Part We recommend you use Transfer Case – Shell Automatic Transmis- — 3.6L Engine sion Fluid 3353. We recommend you use Transfer Case – MOPAR ® ATF+4 ® Automatic — 5.7L Engine Transmission Fluid.
Page 122
MAINTAINING YOUR VEHICLE SRT8 Component Fluid, Lubricant, or Capacities Genuine Part We recommend you use MOPAR ® Antifreeze/Coolant 6.4L Engine 10 Year/ 150,000 Mile 16 Quarts (15.2 Liters) Formula OAT (Organic Additive Technology). For best performance and maximum protection under all types of operating condi- tions, the manufacturer only recommends full synthetic...
MAINTAINING YOUR VEHICLE CAUTION! • Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any “globally compatible”...
Page 124
MAINTAINING YOUR VEHICLE Your authorized dealer will reset the oil change indicator message after completing the scheduled oil change. If a scheduled oil change is performed by someone other than your authorized dealer, the message can be reset by referring to the steps described under “Electronic Vehicle Information Center (EVIC)/Oil Change Required”...
Page 127
MAINTAINING YOUR VEHICLE MAINTENANCE RECORD Odometer Date Signature, Authorized Service Center 20,000 Miles (32,000 km) or 2 Years 30,000 Miles (48,000 km) or 3 Years 40,000 Miles (64,000 km) or 4 Years 50,000 Miles (80,000 km) or 5 Years 60,000 Miles (96,000 km) or 6 Years 70,000 Miles...
Page 129
MAINTAINING YOUR VEHICLE SRT8 – MAINTENANCE RECORD Odometer Date Signature, Authorized Service Center 6,000 Miles (10,000 km) or 6 Months 12,000 Miles (20,000 km) or 12 Months 18,000 Miles (30,000 km) or 18 Months 24,000 Miles (40,000 km) or 24 Months 30,000 Miles (50,000 km) or 30 Months...
MAINTAINING YOUR VEHICLE FUSES Integrated Power Module (fuses) The integrated power module is located on the right side of the engine compartment. This center contains cartridge fuses and mini fuses. A description of each fuse and component may be stamped on the inside cover, otherwise the cavity number of each fuse is stamped on the inside cover that corresponds to the following chart.
Page 131
MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini Fuse Description 20 Amp Blue Trailer Tow Lamps/Park Lamps 40 Amp Green Rear Window Defroster 40 Amp Green Starter Motor Solenoid Feed 20 Amp Blue NGC/PCM Transmission Range 60 Amp Yellow Rad Fan Motor HI/Rad Fan Motor Low 30 Amp Pink Front Wiper Ground...
Page 132
MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini Fuse Description 25 Amp Natural Rear Wiper On 20 Amp Yellow Fuel Pump Motor Output/Diesel Lift Pump (Export Only) 10 Amp Red Driver Door Switch Bank 10 Amp Red Ignition Switch Feed/WIN/PEM 15 Amp Blue PCM Feed/TCM 10 Amp Red CORAX TPM...
MAINTAINING YOUR VEHICLE TIRE PRESSURES • Check the inflation pressure of each tire, including the spare tire, at least monthly and inflate to the recommended pressure for your vehicle. • The tire pressures recommended for your vehicle are found on the “Tire and Loading Information”...
MAINTAINING YOUR VEHICLE WHEEL AND WHEEL TRIM CARE • All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. • To remove heavy soil and/or excessive brake dust, use MOPAR ®...
CONSUMER ASSISTANCE CHRYSLER GROUP LLC CUSTOMER CENTER P.O. Box 21–8004 Auburn Hills, MI 48321–8004 Phone: 1–877–426–5337 CHRYSLER CANADA INC. CUSTOMER CENTER P.O. Box 1621 Windsor, Ontario N9A 4H6 Phone: 1–800–465–2001 (English) Phone: 1–800–387–9983 (French) ASSISTANCE FOR THE HEARING IMPAIRED • To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center.
• A street address is required when ordering manuals (no P.O. Boxes). • The Owner's Manual and User Guide electronic files are also available on the Chrysler, Jeep, Ram Truck and Dodge websites. • Click on the "For Owners" tab, select "Owner/Service Manuals", then select your desired model year and vehicle from the drop down lists.
• How do I configure my Universal Garage Door Opener (HomeLink)? pg. 82 OFF-ROAD CAPABILITIES • How do I shift into different four-wheel drive selections? pg. 88 UTILITY • How do I know how much I can tow with my Jeep Grand Cherokee? pg. 89...
Page 142
FAQ (How To?) SRT8 • How do I operate the paddle shifters? pg. 92 WHAT TO DO IN EMERGENCIES • What do I do if my TPMS warning light is blinking? pg. 96 • How do I change a flat tire? pg. 100 •...
This guide has been prepared to help you get quickly acquainted with your new Jeep and to provide a convenient reference source for common questions. However, it is not a substitute for your Owner’s Manual. For complete operational instructions, maintenance procedures and important safety messages, please consult your Owner’s...
Jeep.com Download a free Vehicle Information by visiting your application store, Keyword (Jeep Vehicle Info), or scanning the Microsoft Tag. To put U.S. Only Microsoft Tags to work Get the free mobile app for your phone for you, use your mobile phone’s browser or App http://gettag.mobi...
Need help?
Do you have a question about the 2013 Grand Cherokee and is the answer not in the manual?
Questions and answers