TABLE OF CONTENTS Universal Garage Door Opener INTRODUCTION/WELCOME (HomeLink ) ....53 ® Welcome From Chrysler Group LLC ..2 Power Inverter ....54 CONTROLS AT A GLANCE Power Outlet .
INTRODUCTION/WELCOME WELCOME FROM CHRYSLER GROUP LLC Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. Your new Chrysler Group LLC vehicle has characteristics to enhance the driver's control under some driving conditions.
CONTROLS AT A GLANCE INSTRUMENT CLUSTER Warning Lights - Low Fuel Warning Light - Charging System Light** - Oil Pressure Warning Light** - Engine Temperature Warning Light - Transmission Temperature Warning Light - Anti-Lock Brake (ABS) Light** - Airbag Warning Light** - Electronic Throttle Control (ETC) Light - Tire Pressure Monitoring System (TPMS) Light - Seat Belt Reminder Light...
Page 9
CONTROLS AT A GLANCE Indicators - Turn Signal Indicators - Adaptive Cruise Control (ACC) SET Indicator* - High Beam Indicator - Hill Descent Control Indicator* - Front Fog Light Indicator* - Position Light Indicator* - Vehicle Security Indicator* - Electronic Stability Control (ESC) Off Indicator* - TOW/HAUL Indicator* - Windshield Washer Fluid Low...
GETTING STARTED KEY FOB Locking And Unlocking The Doors/Liftgate • Press the LOCK button once to lock all the doors and the liftgate. Press the UNLOCK button once to unlock the driver’s door only and twice within five seconds to unlock all the doors and liftgate.
GETTING STARTED WARNING! • Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be severely injured or killed. Children should be warned not to touch the parking brake, brake pedal, or the shift lever. Do not leave the Key Fob inside the vehicle or in the ignition.
GETTING STARTED To Lock the Vehicle: • Both front door handles have LOCK buttons located on the outside of the handle. With one of the vehicle's Keyless Enter-N-Go Key Fobs located outside the vehicle and within 5 ft (1.5m) of the driver's or passenger front door handle, press the door handle LOCK button to lock all four doors and liftgate.
Page 13
GETTING STARTED Engine Starting/Stopping Starting • With a valid Keyless Enter-N-Go Key Fob inside the vehicle. • Place the shift lever in PARK or NEUTRAL. • While pressing the brake pedal, press the ENGINE START/STOP button once. If the engine fails to start, the starter will disengage automatically after 10 seconds.
GETTING STARTED THEFT ALARM To Arm • Keyless Enter-N-Go button installed: Press the Keyless Enter-N-Go Start/Stop button until the Electronic Vehicle Information Center (EVIC) indicates that the vehicle ignition is “OFF”. Press the power door lock switch while the door is open, press the Key Fob LOCK button, or with one of the Key Fobs located outside the vehicle and within 5 ft (1.5m) of the driver's and passenger front door handles, press the Keyless Enter-N-Go LOCK button located on the door handle.
GETTING STARTED • A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.).
GETTING STARTED WARNING! (Continued) • Being too close to the steering wheel or instrument panel during Advanced Front Airbag deployment could cause serious injury, including death. Airbags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel.
GETTING STARTED • Loosen the child seat adjusters on the lower straps and tether straps so that you can attach the hook or connector to the lower tether anchorages more easily. • Attach the lower hooks or connectors over the top of the anchorage bars, pushing aside the seat cover material.
GETTING STARTED WARNING! • In a collision, an unrestrained child, even a tiny baby, can become a projectile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.
GETTING STARTED Memory Seat • The memory seat feature allows you to save two different driver seating positions (excluding lumbar position), driver's outside mirror, tilt/telescoping steering column position, and radio station preset settings. The memory seat buttons are located on the driver's door panel.
Page 20
GETTING STARTED Recliner • Lift the rear lever located on the outboard side of the seat, lean back and release when seat is in desired position. Fold-Flat Front Passenger Seat • The front passenger seat can be folded flat to allow for extended cargo space. Pull up on the recliner lever to fold down the seatback.
GETTING STARTED REAR SEATS 60/40 Split Rear Seat To Lower Rear Seatback • With the front seats fully upright and positioned forward, pull upward on the release lever and fold the rear seatback down. To Raise Rear Seatback • Raise the rear seatback and lock it into place.
GETTING STARTED Front Ventilated Seats • Small fans that draw the air from around the occupant and exhaust it underneath the seat and into the passenger compartment are located in the seat cushion and seatback. The fans draw this air across the surface of the seat using air ducts and fine perforations in the covering help to keep the driver cooler in higher ambient temperatures.
GETTING STARTED HEATED STEERING WHEEL • The steering wheel contains a heating element that heats the steering wheel to one temperature setting. • The heated steering wheel switch is located on the center instrument panel below the climate controls. • Press the switch once to turn the heating element On.
Page 24
GETTING STARTED WARNING! • Do not adjust the steering wheel while driving. The tilt/telescoping adjustment must be locked while driving. Adjusting the steering wheel while driving or driving without the tilt/telescoping adjustment locked could cause the driver to lose control of the vehicle. Failure to follow this warning may result in you and others being severely injured or killed.
OPERATING YOUR VEHICLE HEADLIGHT SWITCH Automatic Headlights/Parking Lights/Headlights • Rotate the headlight switch, located on the instrument panel to the left of the steering wheel, to the first detent for parking lights and to the second detent for headlights • With the parking lights or low beam headlights on, push the headlight switch once for fog lights.
OPERATING YOUR VEHICLE TURN SIGNAL/WIPER/WASHER/HIGH BEAM LEVER Turn Signal/Lane Change Assist • Tap the lever up or down once and the turn signal (right or left) will flash three times and automatically turn off. Front Wipers Intermittent, Low And High Operation •...
OPERATING YOUR VEHICLE Washer Operation • Rotate the center portion of the lever past the second detent to activate the rear washer. High Beam Operation • Push the lever forward to activate the high beams. Pull the lever toward you for flash to pass.
OPERATING YOUR VEHICLE Resume • To resume a previously selected set speed in memory, push the RES + button and release. Cancel • Push the CANCEL button, or apply the brakes to cancel the set speed and maintain the set speed memory. •...
Page 29
OPERATING YOUR VEHICLE WARNING! • Leaving the Electronic or Adaptive Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have a collision. Always leave the Electronic or Adaptive Speed Control system off when you are not using it.
OPERATING YOUR VEHICLE ELECTRONIC RANGE SELECTION (ERS) • Electronic Range Select (ERS) allows you to limit the highest available transmission gear, and can be activated during any driving condition. When towing a trailer or operating the vehicle in off-road conditions, using ERS shift control will help you maximize both performance and engine braking.
OPERATING YOUR VEHICLE MANUAL CLIMATE CONTROLS Air Recirculation • Use recirculation for maximum A/C operation. • For window defogging, turn the recirculation button off. • Recirculation is not allowed in defrost, floor, defrost/floor (mix) modes. AUTOMATIC TEMPERATURE CONTROLS (ATC) Automatic Operation •...
OPERATING YOUR VEHICLE SYNC Temperature Button • Press the SYNC button once to control driver and passenger temperatures simultaneously. Press the SYNC button a second time to control the temperatures individually. Air Recirculation • Use recirculation for maximum A/C operation. •...
OPERATING YOUR VEHICLE BLIND SPOT MONITORING • The Blind Spot Monitoring (BSM) system warning light, located in the outside mirrors, will illuminate if a vehicle moves into a blind spot zone. • The BSM system can also be configured to sound an audible (chime) alert and mute the radio to notify you of objects that have entered the detection zones.
OPERATING YOUR VEHICLE POWER SUNROOF Manual Open/Close • Press and hold the switch rearward to open or forward to close the sunroof. Any release of the switch will stop the movement, and the sunroof will remain in a partially open or closed position until the switch is pressed again. Command View Sunroof With Power Shade NOTE: •...
OPERATING YOUR VEHICLE Pinch Protection Feature • This feature will detect an obstruction in the opening of the sunroof or the shade during Express Close operation. If an obstruction in the path of the sunroof or shade is detected, the sunroof or shade will automatically return to the open position. NOTE: Pinch protection is disabled while the switch is pressed and held during manual opening and closing of the sunroof or shade.
ELECTRONICS NOTE: Your radio may not be equipped with the Uconnect™ Voice Command and Uconnect™ Phone features. To determine if your radio has these features, press the Voice Command button on the radio. You will hear a voice prompt if you have the feature, or see a message on the radio stating “Uconnect Phone not available”...
ELECTRONICS TOUCH-SCREEN RADIOS Media Center 730N CD/DVD/HDD/NAV (Sales Code RER) Media Center 430/430N CD/DVD/HDD (Sales Code RBZ/RHB)
Page 41
ELECTRONICS NOTE: Your radio may not be equipped with the Uconnect™ Voice Command and Uconnect™ Phone features. To determine if your radio has these features, press the Voice Command button on the radio. You will hear a voice prompt if you have the feature, or see a message on the radio stating “Uconnect Phone not available”...
Page 42
ELECTRONICS Hard Disk Drive Operation Copy Complete Audio Disc To Hard-Drive • Media Center 730N: Press the OPEN/CLOSE hard-key. • Media Center 430/430N: Press the LOAD hard-key. • Insert a disc, then press the MENU hard-key. • Touch the MY FILES soft-key, then select MY MUSIC. •...
ELECTRONICS USB Port • The USB Port on the radio allows you to copy songs from a connected USB drive or supported media device onto your Media Center hard drive. • Media Center 430 and 430N also offer the ability to play songs from connected USB drives, or supported media devices, through the USB port located in the center console.
Page 44
ELECTRONICS Change Stored Home Address • Press the MENU hard-key, then touch the MY FILES soft-key. • Touch the MY ADDRESS BOOK soft-key, then touch the HOME soft-key. • In the Home Address Information screen, touch the EDIT CONTACT soft-key, then touch the CHANGE ADDRESS soft-key in the next screen.
Page 45
ELECTRONICS Finding a Point of Interest • Touch the NAV soft-key in the upper-right corner of your radio screen, to access the Navigation system. • Touch the Where To? soft-key to program a destination. • Next touch one of the subcategories to search for your destination. Address, Points of Interest, Recently Found, Favorites and Intersection are a few of the options.
ELECTRONICS • SIRIUS Travel Link brings a wealth of useful information into your vehicle and right to your fingertips: • Weather • View detailed weather conditions at your current location. • Ski Info • View ski and snowboarding conditions at ski resorts. •...
NOTE: The Uconnect™ Phone requires a mobile phone equipped with the Bluetooth ® Hands-Free Profile, Version 0.96 or higher. For Uconnect™ customer support, call 1–877–855–8400 or visit jeep.com/uconnect. Phone Pairing NOTE: Pairing is a one-time initial setup before using the phone. You will also need to...
Page 48
ELECTRONICS Phonebook Edit • Press the Phone button • (After the BEEP), say “phonebook”. • (After the BEEP), say “new entry” or “list names” or “delete”. • Follow the prompts. Receiving A Call – Accept (And End) • When an incoming call rings/is announced on Uconnect™, press the Phone button •...
• It also allows you to respond by selecting from various pre-defined phrases. • Not all phones are compatible with this feature. Refer to the phone compatibility list at jeep.com/uconnect. Connected mobile phones must be bluetooth-compatible, and paired with your radio.
ELECTRONICS WARNING! Any voice commanded system should be used only in safe driving conditions following local laws and phone use. All attention should be kept on the roadway ahead. Failure to do so may result in a collision causing you and others to be severely injured or killed.
Page 51
USB port also supports playing music from compatible external USB Mass Storage Class memory devices. For supported audio file formats, refer to the USB Port section on the Owner's Manual on the DVD. Refer to www.jeep.com/uconnect website for a list of tested iPod s.
ELECTRONICS Bluetooth Streaming Audio (Media Center 430/430N/230/130 only) ® If equipped with Uconnect™ Voice Command, your bluetooth-equipped iPod devices, ® cellphones or other media players, may also be able to stream music to your vehicle's speakers. Your connected device must be bluetooth-compatible, and paired with your Media Center radio (see Uconnect™...
Page 53
ELECTRONICS SIRIUS Backseat TV™ • Press the MENU hard-key, then touch the Rear VES™ soft-key. If a chapter list appears on the right side of the screen, touch the HIDE LIST soft key to display the Rear VES™ Control screen. •...
ELECTRONICS ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) • The EVIC features a driver interactive display that is located in the instrument cluster. Pressing the controls on the left side of the steering wheel allows the driver to select vehicle information and Personal Settings.
ELECTRONICS UNIVERSAL GARAGE DOOR OPENER (HomeLink ® Programming HomeLink ® Begin Programming • The HomeLink buttons are located in ® the overhead console. • Erase all channels before you begin programming by holding the two outside buttons for up to 20 seconds until the red indicator flashes.
ELECTRONICS Using HomeLink ® • To operate, simply press and release the programmed HomeLink button and the ® programmed device will operate. • Refer to your Owner’s Manual on the DVD for further details. If you have any problems programming HomeLink , or require assistance, please call toll-free ®...
ELECTRONICS POWER OUTLET • The front power outlet is located inside the center storage bin of the instrument panel. Push inward on the storage lid to open the compartment and gain access to this power outlet. • A second front power outlet is located inside the center console.
OFF-ROAD CAPABILITIES QUADRA-TRAC I • 4WD HI ® • NEUTRAL FOUR-WHEEL DRIVE • 4WD LOW Quadra-Trac I Operating ® • This transfer case is fully automatic in the 4WD HI mode. Instructions/Precautions - 3.6L Only • When additional traction is required, the 4WD LOW position can be used •...
Page 59
OFF-ROAD CAPABILITIES • Press and hold the NEUTRAL button 4WD LOW To 4WD HI located near the 4WD mode control • With the vehicle at speeds of 0 to knob with a pen or similar object for 3 mph (0 to 5 km/h), the ignition four seconds.
Page 60
OFF-ROAD CAPABILITIES • Sand/Mud – Off-road calibration • The Quadra-Lift™ air suspension for use on low traction surfaces such system uses a lifting and lowering as mud, sand, or wet grass. Driveline pattern which keeps the headlights is maximized for traction. Some from shining into oncoming traffic.
OFF-ROAD CAPABILITIES • Normal Ride Height WARNING! (NRH) – This is the standard position of the • You or others could be injured if suspension and is meant you leave the vehicle unattended for normal driving. Only with the transfer case in the N the bottom Indicator lamp (Neutral) position without first fully on the “Up”...
UTILITY RECREATIONAL • Using a ballpoint pen or similar object, press and hold the recessed TOWING (BEHIND transfer case N (Neutral) button for four seconds, until the light next to the MOTORHOME, ETC.) N symbol starts to blink, indicating shift in progress. The light will stop Two-Wheel Drive Models blinking (stay on solid) when the shift •...
Page 64
UTILITY CAUTION! WARNING! • Towing with the rear wheels on the You or others could be injured if you ground will cause severe leave the vehicle unattended with the transmission damage. Damage transfer case in the NEUTRAL position from improper towing is not without first fully engaging the covered under the New Vehicle parking brake.
WHAT TO DO IN EMERGENCIES 24-HOUR TOWING ASSISTANCE - U.S. ONLY • Dial toll-free 1-800-521-2779 or 1-800-363-4869 for Canadian residents. • Provide your name, vehicle identification number and license plate number. • Provide your location, including telephone number, from which you are calling. •...
WHAT TO DO IN EMERGENCIES CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style.
WHAT TO DO IN EMERGENCIES • The “ESC Activation/Malfunction Indicator Light” starts to flash as soon as the tires lose traction and the ESC system becomes active. If the light begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions.
WHAT TO DO IN EMERGENCIES Oil Change Indicator Message • If an “oil change” message (shown as Oil Change Required) appears and a single chime sounds, it is time for your next required oil change. Resetting The Light After Servicing •...
WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING Jack Location • The scissor-type jack and tire changing tools are located in the rear cargo area, below the load floor. Spare Tire Stowage • The spare tire is located under the load floor in the rear cargo area. Preparations For Jacking •...
WHAT TO DO IN EMERGENCIES • Block both the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, block the left rear wheel. NOTE: Passengers should not remain in the vehicle when the vehicle is being jacked.
Page 71
WHAT TO DO IN EMERGENCIES • Turn the jack screw clockwise to firmly engage the jack saddle with the lift area of the sill flange. • Raise the vehicle by turning the jack screw clockwise. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire.
WHAT TO DO IN EMERGENCIES WARNING! (Continued) • If it is necessary to retrieve the spare tire from under the vehicle on the side of the vehicle close to moving traffic, pull far enough off the road to avoid the danger of being hit.
WHAT TO DO IN EMERGENCIES Jump-Starting Procedure • Connect the positive (+) end of the jumper cable to the remote positive (+) post of the discharged vehicle. • Connect the opposite end of the positive (+) jumper cable to the positive (+) post of the booster battery.
WHAT TO DO IN EMERGENCIES WARNING! • When temperatures are below the freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump-starting because the battery could rupture or explode and cause personal injury. Battery temperature must be brought above freezing point before attempting a jump-start.
WHAT TO DO IN EMERGENCIES SHIFT LEVER OVERRIDE • If a malfunction occurs and the shift lever cannot be moved out of the PARK position, you can use the following procedure to temporarily move the shift lever: • To access the shift lever override, remove the rubber cupholder liner to the right of the shift lever.
WHAT TO DO IN EMERGENCIES EVENT DATA RECORDER (EDR) • This vehicle is equipped with an event data recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed.
MAINTAINING YOUR VEHICLE OPENING THE HOOD • Pull the hood release lever located below the steering wheel at the base of the instrument panel. • Reach into the opening beneath the center of the hood and move the safety latch lever while lifting the hood at the same time.
Page 79
MAINTAINING YOUR VEHICLE Fuel Door Emergency Release • To manually open the fuel door, remove the storage bin and pull the release cable located in the rear cargo area.
MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Component Fluid, Lubricant, or Capacities Genuine Part 3.6L Engine MOPAR Engine 10.4 Quarts (9.9 Liters) ® Coolant/Antifreeze 5-Year/100,000 Mile Formula or equivalent 5.7 Liter Engine – Without MOPAR Engine 15.4 Quarts (14.6 Liters) ® Trailer Tow Package Coolant/Antifreeze 5-Year/100,000 Mile...
Page 83
MAINTAINING YOUR VEHICLE Fluid, Lubricant, or Component Capacities Genuine Part Transfer Case (MP3023 MOPAR NV 247/245 ® Two Speed Only) Transfer Case Lubricant or — equivalent. Axle Differential MOPAR Synthetic Gear ® (Front/Rear) & Axle Lubricant SAE 75W–140 API–GL5 or —...
Page 85
MAINTAINING YOUR VEHICLE Maintenance Record Odometer Date Signature, Authorized Service Center 8,000 Miles (13,000 km) or 6 Months 16,000 Miles (26,000 km) or 12 Months 24,000 Miles (39,000 km) or 18 Months 32,000 Miles (52,000 km) or 24 Months 40,000 Miles (65,000 km) or 30 Months 48,000 Miles...
Page 87
MAINTAINING YOUR VEHICLE Integrated Power Module (fuses) The integrated power module is located on the right side of the engine compartment. This center contains cartridge fuses and mini fuses. A description of each fuse and component may be stamped on the inside cover, otherwise the cavity number of each fuse is stamped on the inside cover that corresponds to the following chart.
Page 88
MAINTAINING YOUR VEHICLE Cartridge Cavity Mini Fuse Description Fuse 20 Amp Yellow HFM/Vanity Lamp/UGDO Mod 10 Amp Red HVAC (ATC) 30 Amp Green Radio/Amplifier 20 Amp Yellow Main #2 CCN/WIN/ITM/Siren/ Multifunction Switch (SCM) 20 Amp Yellow Back Up Camera (Domestic Only) 20 Amp Yellow Power Seat Module(s)/Adaptive Cruise Control/Audio Telematics/DRL Relay/Air...
MAINTAINING YOUR VEHICLE CAUTION! • When installing the integrated power module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the integrated power module and possibly result in a electrical system failure.
MAINTAINING YOUR VEHICLE WHEEL AND WHEEL TRIM CARE • All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. • To remove heavy soil and/or excessive brake dust, use MOPAR Wheel Cleaner or ®...
Bell Relay Service operator. NOTE: • The Owner's Manual and User Guide electronic files are also available on the Chrysler, Jeep and Dodge websites. • Click on the "For Owners" tab, select "Owner/Service Manuals", then select your desired model year and vehicle...
CONSUMER ASSISTANCE REPORTING SAFETY In Canada • If you believe that your vehicle has a DEFECTS IN THE 50 safety defect, you should contact the UNITED STATES AND Customer Service Department immediately. Canadian customers who WASHINGTON, D.C. wish to report a safety defect to the Canadian government should contact •...
AUTHENTIC ACCESSORIES BY MOPAR ® • The following highlights just some of the many Authentic Jeep Accessories by Mopar featuring a fit, finish, and functionality specifically for your Jeep Grand Cherokee. • In choosing Authentic Accessories you gain far more than expressive style, premium protection, or extreme entertainment, you also benefit from enhancing your vehicle with accessories that have been thoroughly tested and factory-approved.
Driving and Alcohol: Drunken driving is one of the most frequent causes of collisions. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
Page 100
Jeep.com This guide has been prepared to help you get quickly acquainted with your new Jeep and to provide a convenient reference source for common questions. However, it is not a substitute for your Owner’s Manual. For complete operational instructions, maintenance...
Need help?
Do you have a question about the Grand Cherokee 2011 and is the answer not in the manual?
Questions and answers