Sharp MX-M550U Service Manual page 85

7) Press the P or Start key.
This applies the adjustment value.
Pressing the Start key starts print operation as well as applying
the adjustment value.
8) Check the print density.
Repeat steps 5 to 8 until an acceptable print density is obtained.
Adjusting the Fax print density through this simulation changes the
print density settings for all Fax modes to the density level applied
by carrying out this simulation.
The Fax mode print density settings for individual Fax modes
adjusted through Simulations 46-13, -14, -15, -16 and -45 are
changed to the print density level applied by this simulation.
10-B Adjust the fax mode print density in
standard mode
10-C Adjust the fax mode print density in small-
character mode
10-D Adjust the fax mode print density in fine
mode
10-E Adjust the fax mode print density in super
fine mode
10-F Adjust the fax mode print density in 600dpi
mode
This adjustment is intended to the print mode for each Fax mode
individually. In manual mode, the print density setting for each print
density adjustment level (1 to 5) can be adjusted to a custom den-
sity level.
1) Set the test chart (UKOG-0162FCZZ) on the original table so
that it aligns with the front frame. Then put four or five pieces of
A3 (11" x 17") paper.
2) Go through the simulation modes that correspond to the Fax
modes for which to adjust the print density (i.e., the modes
specified in Simulations 46-13, -14, -15, -16, or -45).
Select 1,
and press
[START] key.
Select 0, and press [START] key.
Select 2, and press
[START] key.
0
1
2
3
4
5
6
7
8
MX-M700N ADJUSTMENTS 6 – 34
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL). SELECT 0-8, AND PRESS
START.
0.TRAY SELECT 1 1.PRINT START
2.EXP LEVEL 1
3.AUTO 50 4.1.0 50
6.3.0 50 7.4.0 50
Select other than 0 - 2,
Press [SYSTEM SETTINGS]
and press [START] key.
key.
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL),INPUT VALUE 0-99, AND
PRESS START.
4.1.0
Press [START] key.
Press [SYSTEM SETTINGS]
key, or terminate copying.
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL). NOW PRINTING.
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL). SELECT 1-6, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT 6.LCC
(ABOVE +20:DSPF MODE)
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL). SELECT 3-8, AND PRESS START.
(EXP.LEVEL SELECT)
3.AUTO 4.1.0
6.3.0 7.4.0
Item
TRAY SELECT Paper feed tray selection
PRINT START Print start (Default)
EXP LEVEL Exposure level selection
AUTO Auto
1.0 Exposure level 1
2.0 Exposure level 2
3.0 Exposure level 3
4.0 Exposure level 4
5.0 Exposure level 5
1
5.2.0 50
8.5.0 50
50
Press [START] key, or press
[SYSTEM SETTINGS] key.
1
Press [START] key, or press
[SYSTEM SETTINGS] key.
5.2.0
1
8.5.0
Setting
Default
range
0 – 99 50