Sharp MX-M550U Service Manual page 130

NOTE: When [P] key is pressed after entering an adjustment value
in this simulation, the adjustment value is set. When
[START] key is pressed, the adjustment value is set and
copying is performed.
To select exposure mode, perform the following procedures.
1) Enter 2 with 10-key.
2) Press [START] key. (The mode is changed to the exposure
mode.)
3) Enter the number corresponding to the exposure level to be
used with 10-key, and press [START] key.
3 AE 3.0 AE mode
4 CH 3.0 Text mode 3.0
5 MIX 3.0 Text/Photo mode 3.0
6 PHOTO 3.0 Photo mode 3.0
SIMULATION 46-2
EXP. LEVEL SETUP (2). SELECT 0-6, AND PRESS START.
0. TRAY SELECT 1 1. COPY START
2. EXP LEVEL 1
3. AE 3.0 50 4. CH 3.0
5. MIX 3.0 50 6. PHOTO 3.0
46-9
Purpose Adjustment
Function (Purpose) Used to adjust the print density for each
density level (display value) in the copy
mode (binary - Text mode). An optional
print density can be set for each density
level (display value).
Section —
Operation/Procedure
1) Select the number corresponding to the copy density adjust-
ment level with 10-key. (Select one of 3 - 11.)
2) Press the [START] key.
3) Enter the copy density level with 10-key.
Item
0 TRAY SELECT Paper feed tray
selection
1 COPY START Copy START
(Default)
2 EXP LEVEL Exposure level
selection
3 1.0 Exposure level 1.0
4 1.5 Exposure level 1.5
5 2.0 Exposure level 2.0
6 2.5 Exposure level 2.5
7 3.0 Exposure level 3.0
8 3.5 Exposure level 3.5
9 4.0 Exposure level 4.0
10 4.5 Exposure level 4.5
11 5.0 Exposure level 5.0
4) Press the [P] or [START] key.
The adjustment value is set.
When [START] key is pressed, copy is performed and the
adjustment value is set simultaneously.
Check the density of the printed copy image.
Normal display
ERROR display Door open
Jam
Paper empty
To select paper (paper feed tray), perform the following procedures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
1
50
50
Setting
Default
range
0 - 99
NOW COPYING.
DOOR OPEN.
JAM
PAPER EMPTY.
MX-M700N SIMULATION 7 – 36
3) Enter the number corresponding to the paper feed tray to be
used with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
1 TRAY1
2 TRAY2
3 TRAY3
4 TRAY4
5 BPT
6 LCC
NOTE: When [P] key is pressed after entering an adjustment value
in this simulation, the adjustment value is set. When
[START] key is pressed, the adjustment value is set and
copying is performed.
SIMULATION 46-9
EXP. LEVEL SETUP (CHAR.2). SELECT 0-11, AND PRESS START.
0. TRAY SELECT
2. EXP LEVEL
3. 1.0
6. 2.5
9. 4.0
46-10
Purpose
Function (Purpose) Used to adjust the print density for each
Section
Operation/Procedure
1) Select the number corresponding to the copy density adjust-
ment level with 10-key. (Select one of 3 - 11.)
2) Press the [START] key.
3) Enter the copy density level with 10-key.
0 TRAY SELECT
1 COPY START
2 EXP LEVEL
3 1.0
4 1.5
5 2.0
50
6 2.5
7 3.0
8 3.5
9 4.0
10 4.5
11 5.0
4) Press the [P] or [START] key.
The adjustment value is set.
When [START] key is pressed, copy is performed and the
adjustment value is set simultaneously.
Check the density of the printed copy image.
Normal display
ERROR display
To select paper (paper feed tray), perform the following procedures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray to be
used with 10-key.
TRAY1
TRAY2
TRAY3
TRAY4
Manual paper feed
Side LCC
1 1. COPY START
1
50 4. 1.5 50 5. 2.0 50
50 7. 3.0 50 8. 3.5 50
50 10. 4.5 50 11. 5.0 50
Adjustment
density level (display value) in the copy
mode (binary - Text/Photo mode). An
optional print density can be set for each
density level (display value).
—
Item
Paper feed tray
selection
Copy START (Default)
Exposure level
selection
Exposure level 1.0
Exposure level 1.5
Exposure level 2.0
Exposure level 2.5
Exposure level 3.0
Exposure level 3.5
Exposure level 4.0
Exposure level 4.5
Exposure level 5.0
Door open
Jam
Paper empty
1
Setting
Default
range
0 - 99 50
NOW COPYING.
DOOR OPEN.
JAM
PAPER EMPTY.