Sharp MX-M550U Service Manual page 104

3-3
Purpose Operation test/Check
Function (Purpose) Used to check the operation of the load in
the finisher and the control circuit.
Section Finisher
Operation/Procedure
1) Select the number corresponding to the target of operation
check with 10-key.
2) Press the [START] key.
The load selected in procedure 1 is operated.
The operation can be stopped with the [SYSTEM SETTINGS] key.
1 SL7 Belt wait solenoid
2 SL6 Wait solenoid
3 SL5 Paddle solenoid
4 SL3 Buffer exit port solenoid
5 SL2 Buffer entry port solenoid
6 SL1 Flapper solenoid
7 M10 Tray 2 lift motor
8 M9 Entry port transport motor
9 M8 No. 2 transport motor
10 M7 Oscillation motor
11 M6 Staple motor
12 M5 Tray 1 lift motor
13 M4 Stapler shift motor
14 M3 Alignment motor
15 M2 Paper exit motor
16 M1 No. 1 transport motor
(When the punch unit is installed)
17 M2P Punch side resist motor
18 M1P Punch motor
(When the saddle unit is installed.
19 SL4S Transport plate contact solenoid
20 SL2S No. 2 paper deflection plate solenoid
21 SL1S No. 1 paper deflection plate solenoid
22 M8S Paper holding motor
23 M7S Stitch motor: Front
24 M6S Stitch motor: Rear
25 M5S Saddle alignment motor
26 M4S Paper positioning motor
27 M3S Guide motor
28 M2S Paper folding motor
29 M1S Saddle transport motor
SIMULATION 3-3
FINISHER LOAD TEST. SELECT 1-
3-10
Purpose Adjustment
Function (Purpose) Finisher (AR-F16) adjustment
Section Finisher
Operation/Procedure
1) Select the number that corresponds to the adjustment item
with 10-key.
2) Press the [START] key.
3) Enter the adjustment value with 10-key.
4) Press [START] key. (The entered value is stored.)
Item
1 Saddle stitch/folding
position adjustment
2 Alignment position
adjustment
AND PRESS START.
2
Setting range
192 - 208, 1STEP: 0.25 mm
2 - 18, 1STEP: 0.35 mm
MX-M700N SIMULATION 7 – 10
Item
3 Staple binding position
adjustment
4 Punch center
adjustment
5 Punch hole position
adjustment (Paper feed
direction)
6 Stack tray standby
position adjustment
(Small size)
7 Stack tray standby
position adjustment
(Large size)
SIMULATION 3-10
FINISHER SETTING. SELECT 1-7 AND PRESS START.
1. SADDLE POSITION
2. ALIGNMENT POSITION
3. STAPLE POSITION
4. PUNCH CENTER
5. PUNCH HOLE
6. TRAY WAITING POSITION(S-SIZE)
7. TRAY WAITING POSITION(L-SIZE)
3-30
Purpose Operation test/Check
Function (Purpose) Used to check the operations of the sen-
sors and detectors in the inserter and the
related circuit.
Section Inserter
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The active sensors and detectors are highlighted.
TH_SEN Sub tray pull-out detection
TS_SEN Sub tray storage detection
T_SEN Inserter tray paper size detection
EMP_SEN Inserter tray empty detection
REG_SEN Inserter resist sensor
TIM_SEN Inserter timing sensor detection
JCK_SEN Inserter cover open/close sensor
H_SEN Inserter reverse sensor
HI_SEN Inserter paper exit sensor
HYK_SEN Inserter reverse unit open/close sensor
S_SW Inserter set SW
KC_SEN Base cover open/close sensor
P_ST_SW Inserter start SW
P_MO_SW Inserter staple mode select SW
P_PN_SW Inserter punch select SW
SIMULATION 3-30
INSERTER SENSOR CHECK.
TH_SEN TS_SEN
REG_SEN TIM_SEN
HI_SEN HYK_SEN
P_ST_SW P_MO_SW
Setting range
68 - 132, 1STEP: 0.152 mm
37 - 63, 1STEP: 0.15mm
35 - 57, 1STEP: 0.26mm
5 - 35, 1STEP: 1mm
5 - 35, 1STEP: 1mm
1
T_SEN EMP_SEN
JCK_SEN H_SEN
S_SW KC_SEN
P_PN_SW