Adjustment Value/Simulation/Storage Data; Simulation Adjustment Value/ Set Value Data; Each Storage Data - Sharp MX-M550U Service Manual

MX-M700N
[7] SIMULATION
1. Adjustment value/Simulation and
storage data
A. Simulation adjustment value/ Set value data
Each controller is provided with an EEPROM. The adjustment/set
values are collected to the MFP controller. If they are changed, they
are sent back and saved.
MFP CONTROLLER
LCD
Saved adjustment value
send (When the power is
turned on, etc.)
ENGINE
CONTROLLER
B. Each storage data
(1) (Data saved by the PCU PWB)
Counters Adjustment value
Drum rotation time Developing bias voltage
counter value
(Accumulated time)
Developer unit Cleaning mode
rotation time counter Developing bias voltage
value
Toner supply time Main high voltage
(Block IC CHIP) adjustment
Drum rotating time Transfer charger voltage
(Block IC CHIP) value
Total counter Transfer belt cleaning
voltage value
Maintenance Toner concentration
counter reference value
Developing counter Density correction start set
time (Developer unit)
Drum counter Density correction rotation
time (Developer tank)
Toner cartridge Density correction amount
counter (Developer tank)
Valid paper counter Correction execution
direction, upper/lower limit
(Developer tank)
Tray 1 paper feed Toner concentration
counter temperature correction (low
temperature side) correction
amount
Tray 2 paper feed Toner concentration
counter temperature correction (low
temperature side) set
temperature
Tray 3 paper feed Toner concentration
counter temperature correction (low
temperature side) release
temperature
Tray 4 paper feed Toner concentration
counter temperature correction (high
temperature) correction
amount
Manual paper feed Toner concentration
counter temperature correction (high
temperature side) judgment
temperature
When the value is changed,
it is sent and saved.
-
SCANNER
CONTROLLER
Others
Serial number
Trouble history
Tray 1 size
Tray 2 size
Manual destination
information
Tray 3 destination
information
Tray 4 destination
information
Tray 1 paper
remaining quantity
data
Tray 2 paper
remaining quantity
data
Tray 3 paper
remaining quantity
data
Tray 4 paper
remaining quantity
data
Final toner
concentration
sensor output
value
Toner cartridge IC
CHIP destination
Counter mode
setting
MX-M700N SIMULATION 7 – 1
Counters Adjustment value
ADU paper feed Toner concentration
counter temperature correction (high
temperature side) judgment
voltage
Staple counter Toner concentration
temperature correction (high
temperature side) correction
value
Punch counter Toner concentration
temperature correction (low
temperature side) release
time
Main unit right-side Toner concentration
paper exit counter temperature correction (high
temperature side) toner
concentration delay time
Side LCC paper Multi-purpose width
feed counter adjustment value
Inserter counter Manual width adjustment
value
Saddle staple Heater lamp temperature
counter (Center, normal control)
Fuser Web Send Lead edge adjustment
counter
Led edge void set value
Rear edge void set value
Side edge setting
Print off-center adjustment
value
Resist amount adjustment
value
Laser power adjustment
value
PPD1 sensor adjustment
Process correction inhibit
allow set value
Developing bias rising
correction wait time
Developing bias rising
correction adjustment value
Built-in finisher jogger
position adjustment
Saddle adjustment value
(2) (Data saved by the scanner control PWB)
Counters Adjustment value
Scan counter Document lead edge
adjustment value
SPF paper pass Document off-center
counter adjustment value
SPF stamp counter Document image loss
amount adjustment value
Document image loss
amount adjustment value
SPF resist amount
adjustment value
Exposure motor speed
adjustment value
Platen document detection
adjustment value
SPF size width detection
adjustment value
Touch panel adjustment
value
Exposure level adjustment
value
gamma change value
OC/SPF exposure
correction value
Shading adjustment value
(CCD/CIS)
CCD shading start position
adjustment value
Others
White paper exit
count setting
Trouble memory
mode setting
Fusing operation
mode (Prevention
against curl)
CE mark
conforming
operation mode
Maintenance cycle
Print stop setting
when developer
life over
Saddle alignment
operation priority
mode
Others
Exposure mode set
value
Scanner serial
number