Sharp MX-3500N Service Manual page 225

Item Button Display item
A ENGIN TRAY1(S)
B TRAY1(L)
C TRAY2(S)
D TRAY2(L)
E MANUAL PLAIN PAPER (S)
F MANUAL PLAIN PAPER (L)
G MANUAL HEAVY PAPER (S)
H MANUAL HEAVY PAPER (L)
I MANUAL OHP
J MANUAL ENV
K ADU PLAIN PAPER (S)
L ADU PLAIN PAPER (L)
M ADU HEAVY PAPER (S)
N ADU HEAVY PAPER (L)
O DESK(S)
P DESK(L)
Q A4LCC
R A3LCC
S A3LCC
<Expression of (Large size) and (Small size)>
(Small size): The paper length in the transport direction is LT
(216mm) or less.
(Large size): The paper length in the transport direction is longer
than LT (216mm).
* Document size judgment of DSPF for items B and D: Small size
for 148mm (A5) or less
* The adjustment unit is the distance of the 0.1 mm unit.
* The smaller the set value is, the smaller the deflection amount of
each specified item is. The greater the set value is, the greater
the deflection amount is.
<Adjustment value>
When the adjustment value is increased, the deflection quantity is
increased. When the adjustment value is decreased, the deflection
quantity is decreased. (When the adjustment value is changed by
1, the stop timing is changed by 1.0 msec.)
SIMULATION NO.51 02
TEST
REGIST ROLLER ADJUSTMENT
A 50
NORMAL_PLAIN_HIGH
A: 50
B 50 NORMAL_PLAIN_LOW
C 50 NORMAL_THIN_HIGH
1 99
D 50 NORMAL_THIN_LOW
SIDE1 SIDE2
Description of item (Mode, document, paper feed
Main unit cassette 1 (upper stage), deflection
adjustment value (small size)
Main unit cassette 1 (upper stage), deflection
adjustment value (large size)
Main unit cassette (lower stage), deflection adjustment
value (small size)
Main unit cassette (lower stage), deflection adjustment
value (large size)
Manual tray, deflection adjustment value (plain paper,
small size)
Manual tray, deflection adjustment value (plain paper,
large size)
Manual feed tray, deflection adjustment value (Heavy
paper, small size)
Manual feed tray, deflection adjustment value (Heavy
paper, large size)
Manual feed tray, deflection adjustment value (OHP)
Manual feed tray, deflection adjustment value
(Envelope)
ADU, deflection adjustment value (Plain paper, small
size)
ADU, deflection adjustment value (Plain paper, large
size)
ADU, deflection adjustment value (Heavy paper, small
size)
ADU, deflection adjustment value (Heavy paper, large
size)
DESK, deflection adjustment value (Plain paper, small
size)
DESK, deflection adjustment value (Plain paper, large
size)
A4LCC, Deflection adjustment value
A3LCC, Deflection adjustment value (small size)
A3LCC, Deflection adjustment value (large size)
0
CLOSE
OK
ENGIN
MX3500N SIMULATION 7 – 117
speed)
Longer size than the above
Longer size than the above
Longer size than the above
Longer size than the above
Longer size than the above
Longer size than the above
Longer size than the above
Longer size than the above
53
53-6
Purpose Adjustment
Function (Purpose) Used to adjust the RSPF/DSPF document
tray size of the main unit.
Section RSPF/DSPF
Item Operation
Operation/Procedure
1) Set the tray document guide to the max. width position, and
press [EXECUTE] key. The button is highlighted and the tray
size volume maximum value adjustment is started.
* During the adjustment, "EXECUTING..." is displayed.
* After completion of the tray size volume maximum value
adjustment, the set value is saved to EEPROM and RAM
and the display is shifted to the tray volume A4R size adjust-
ment value start screen. (Each set value is saved to
EEPROM and RAM at each setting.)
2) Set the tray document guide to A4R (11 x 8.5R) width position
and press [EXECUTE] button. The pressed button is high-
lighted and the tray A4R size adjustment is started.
3) Adjust the tray volume A5R size and the tray size volume min-
imum value according to the above procedures.
4) After completion of the adjustment, "COMPLETE"is displayed.
If the adjustment is not completed normally for any rea-
son,"ERROR"is displayed. In that case, the adjustment must
be executed again.
Set
Transport direction
range
LT size or less 1 to 99
1 to 99
LT size or less 1 to 99
1 to 99
LT size or less 1 to 99
1 to 99
LT size or less 1 to 99
1 to 99
– 1 to 99
– 1 to 99
LT size or less 1 to 99
1 to 99
LT size or less 1 to 99
1 to 99
LT size or less 1 to 99
1 to 99
– 1 to 99
LT size or less 1 to 99
1 to 99
Default
value
30
30
30
30
30
30
45
45
45
45
30
30
45
45
30
30
30
30
30