Sharp MX-3500N Service Manual page 185

[Cancel during execution of the operation]
• To cancel and resume the operation, press [EXECUTE].
(Initial screen)
SIMULATION NO.46-24
TEST
ENGINE HALFTONE AUTO ADJUSTMENT
PRESS [EXECUTE] TO PRINT THE TEST PATCH.
(PLEASE USE SPECIFIED TYPE OF A3 OR 11" 17" SIZE PAPER
(48-patch print)
SIMULATION NO. 46-24
TEST
ENGINE HALFTONE AUTO ADJUSTMENT
TEST PATCH PRINTING IN PROGRESS...
(Output patch read (FACTORY))
SIMULATION NO. 46-24
TEST
ENGINE HALFTONE AUTO ADJUSTMENT
PLEASE SELECT THE MODE (FACTORY) OR (SERVICE) AND PLACE
THE PRINTED TEST PATCH ON DOCUMENT GLASS THEN PRESS [EXECUTE].
,
DARK AREA AT LEFT SIDE ON DOCUMENT GLASS.
FACTORY SERVICE
(16-patch self print)
SIMULATION NO. 46-24
TEST
ENGINE HALFTONE AUTO ADJUSTMENT
ADJUSTED PATCH PRINTING IN PROGRESS.
(Standby for registration process)
SIMULATION NO. 46-24
TEST
ENGINE HALFTONE AUTO ADJUSTMENT
CONFIRM THE ADJUSTED PATCH AND PRESS [OK] TO REGISTER THIS PATCH DATA
,PRESS [REPEAT] TO CONTINUE THIS PROCEDURE.
(Registration of half tone process control reference value)
SIMULATION NO. 46-24
TEST
ENGINE HALFTONE AUTO ADJUSTMENT
PLEASE WAIT.
NOW REGISTERING THE NEW TARGET OF HALFTONE PROCON.
0
CLOSE
FOR THIS ADJUSTMENT
EXECUTE
0
CLOSE
EXECUTE
0
CLOSE
EXECUTE
0
CLOSE
EXECUTE
0
CLOSE
REPEAT OK
0
CLOSE
OK
MX3500N SIMULATION 7 – 77
(Completion of all the processes)
SIMULATION NO. 46-24
TEST
ENGINE HALFTONE AUTO ADJUSTMENT
COMPLETED THIS PROCEDURE.
PLEASE QUIT THIS MODE.
46-25
Purpose Adjustment
Function (Purpose) Used to execute the fine adjustment of sin-
gle color mode color balance.
Section Image process (ICU)
Item Adjustment
Operation/Procedure
1) Select a color to be set. (In this example, [C] (Cyan) is
selected.)
* When a color button ([C](Cyan), [M](Magenta), [Y](Yellow))
is selected, the selected button is highlighted and the adjust-
ment value of the selected button is displayed.
* Only one color can be selected. The selected button is high-
lighted.
In the initial state, [C] is selected.
2) Select the set item with [↑] and [↓] buttons.
The highlighted set value is switched and the value is dis-
played in the setting area.
* If there is any item over [↑], an active display is made and
item is shifted.
If there is no item over [↑], the display grays out and the
operation is invalid.
If there is any item under [↓], an active display is made and
item is shifted.
If there is no item over [↓], the display grays out and the
operation is invalid.
3) Enter the set value with 10-key.
* Press [C] key to clear the entered values.
4) When [OK], [↑], [↓] button, [COLOR], or [BLACK] key is
pressed, the current entered value is saved to EEPROM and
RAM.
* When [CLOSE] button is pressed, the display is shifted to the
copy basic screen of simulation.
* Copying can be performed also by pressing [COLOR]/[BLACK]
key.
<Set range and default value of each setup>
Item Description Range
A RED 0 to 255
B GREEN 0 to 255
C BLUE 0 to 255
D YELLOW 0 to 255
E MAGENTA 0 to 255
F CYAN 0 to 255
SIMULATION NO.46 25
TEST
SINGLE COLOR MODE COLOR BALANCE SETUP
A 255
RED
A:
255
B 255 GREEN
C 255 BLUE
0 255
D 0 YELLOW
K
C
M Y
0
CLOSE
Default value
C M Y
0 255 255
255 0 255
255 255 0
0 0 255
0 255 0
255 0 0
0
CLOSE
OK