Sharp MX-3500N Service Manual page 116

Code
Main Sub
55 1 Used to set the engine soft SW.
2 Used to set the scanner soft SW
3 Used to set the controller soft SW.
56 1 Used to execute data transfer.
2 Used to backup the data (user authentication data, address book, etc.) of
EEPROM, SRAM, or HDD to a USB memory and to restore the data.
60 1 Used to check read/write of the expansion DIMM installed to the MFPcnt PWB.
After completion of execution, the result of each slot is displayed on the panel.
MFPcnt PWB image DRAM read/write operation check, check MFP (memory)
operation.
2 Used to set the data of onboard SDRAM.
61 1 The polygon motor rotation and the BD signal detection are checked.
4 Used to execute self-print of the LSU position adjustment.
62 1 Used to execute the hard disk format (except operation manual area).
* Be sure to format the HDD in FAT32.
2 Used to execute the partial check of the hard disk read/write.
* Be sure to format the HDD in FAT32.
3 Used to execute read/write check (all areas) of the hard disk.
* Be sure to format the HDD in FAT32.
6 Used to execute the HDD self-diagnostics.
* Be sure to format the HDD in FAT32.
7 Used to print the self-diagnostics error log.
* Be sure to format the HDD in FAT32.
8 Used to format the hard disk excluding the system area and operation manual
area.
* Be sure to format the HDD in FAT32.
10 Used to delete the job completion list. (The job log data are also deleted.)
* Be sure to format the HDD in FAT32.
11 Used to delete the document filing data.
* Be sure to format the HDD in FAT32.
12 Used to set Enable/Disable of auto format in HDD trouble.
* Be sure to format the HDD in FAT32.
13 Used to format the hard disk (operation manual area only).
* Be sure to format the HDD in FAT32.
63 1 Used to check the following values related to shading for RGB and OC/RSPF/
DSPF. (3 x 2 = 6 kinds)
2 Used to execute shading forcibly (MX-3500N/4500N).
2 Used to execute shading forcibly (MX-3501N/4501N).
3 Used to execute the gamma correction and density conversion for RGB image
data inputted from the CCD. Gamma correction 1 of the SCAN ASIC and the set
value of color correction are set by calculating from the image data.
5 Used to reset the gamma correction and color correction parameters of the
SCAN ASIC.
6 Used to scan the engine color balance auto adjustment pattern and to display
the sampling result.
7 Used to display and register the engine auto density adjustment scanner target
value (for servicing).
8 Used to execute the standard value reset of the engine auto adjustment scanner
target value (for servicing).
11 Used to set the factory target color balance in the auto color balance adjustment
(SIM46-24).
64 1 Used to execute self-print (Color mode).
2 Used to print the density adjustment pattern.
3 Used to execute self-print. (BW mode)
4 Used to execute self-print.
5 Used to execute self print (PCL).
6 Used to execute the printer self print (PS).
65 1 Used to adjust the touch panel (LCD display section) detection position.
2 Used to check the touch panel (LCD display section) detection position
adjustment result.
67 24 Use to execute the printer setting of auto color calibration.
25 Used to set the manual correction of the printer engine color balance.
26 Used to set the reference scanner target value of the printer engine auto density
adjustment of Simulation 67-24.
Compaired to DEF1, DEF2 and DEF3 are decreased-red color balance target
value.
27 Used to display and register the scanner target value (for servicing) of the
printer engine auto density adjustment.
28 The scanner target value (for servicing) of the printer engine auto density
adjustment is reset to the standard value.
30 Used to set YES/NO of delivery of the main unit calibration data and the process
control correction data to the client PC by the GDI printer.
Function (Purpose)
MX3500N SIMULATION 7 – 8
Section
PCU Setting
Scanner Setting
MFP Setting
MFP Data transfer
Memory, HDD Backup
Image process (MFP) Operation test/Check
– Setting
LSU Operation test/Check
LSU Adjustment
MFP (HDD) Data clear
MFP (HDD) Operation test/Check
MFP (HDD) Operation test/Check
MFP (HDD) Operation test/Check
MFP Operation test/Check
MFP (HDD) Data clear
MFP (HDD) Data clear
MFP (HDD) Data clear
MFP (HDD) Data clear
MFP (HDD) Data clear
Scanner (Exposure) Adjustment/Setup/Operation
data output/Check (Display/Print)
Scanner Adjustment
Scanner Adjustment
Scanner (scan) Adjustment
Scanner Adjustment
Image process (ICU) Adjustment/Setup/Operation
data output/Check (Display/Print)
Image process (ICU) Setting
Image process (ICU) Setting
Scanner (Scanning) Setting
Printer Operation test/Check
Printer Adjustment/Setup/Operation
data output/Check (Display/Print)
Printer Operation test/Check
Printer Operation test/Check
Printer Operation test/Check
Printer Operation test/Check
Operation panel Adjustment
Operation panel Adjustment/Setup/Operation
data output/Check (Display/Print)
Printer Adjustment
Printer Adjustment
Printer Adjustment
Printer Adjustment
Scanner Adjustment
Printer Setting
Purpose