Sharp MX-3500N Service Manual page 141

SIMULATION NO.26-10
TEST
NETWORK SCANNER TRIAL MODE SETUP
A : 1
TRIAL MODE (0:YES 1:NO)
A:
1
[ 0~ 1 ]
26-18
Purpose Setting
Function (Purpose) Used to set the toner save mode.
Section —
Item —
Operation/Procedure
1) Use [↑] and [↓] buttons to select an item.
The set value is highlighted and the value is displayed in the
setting area.
* When there is an item over [↑], the display becomes active
and shifts to another item.
When there is no item over [↑], the display grays out and the
operation is disabled.
When there is an item under [↓], the display becomes active
and shifts to another item.
When there is no item under [↓], the display grays out and
the operation is disabled.
2) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
3) When [OK] button is pressed, the current entered value is
saved to EEPROM and RAM.
* When [↑], [↓] button, [COLOR], or [BLACK] key is pressed,
the value is saved to EEPROM and RAM.
<Setting range and default value of each set value>
Item Display
A COPY 0 Copy toner save mode
(1:YES 0:NO) is allowed
1 Copy toner save mode
is inhibited.
B PRINTER 0 Printer toner save
(1:YES 0:NO) mode is allowed.
1 Printer toner save
mode is inhibited.
SIMULATION NO.26 18
TEST
TONER SAVE MODE SETUP
A 0
COPY(1:YES 0:NO)
A: 0
B 0 PRINTER(1:YES 0:NO)
0 1
26-30
Purpose Setting
Function (Purpose) Used to set allow/inhibit of HL slow-up con-
trol (CE mark support control).
Section —
Item Specifications (Operation mode (common
operation))
CLOSE
Setting Default
Content
range value
0 to 1 0
0 to 1 0
CLOSE
MX3500N SIMULATION 7 – 33
Operation/Procedure
0
1) When the machine enters the simulation, the following screen
is displayed.
2) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
3) When [OK] button is pressed, the current entered value is
saved to EEPROM and RAM.
* When [COLOR], or [BLACK] key is pressed, the current set
value is saved to EEPROM and RAM.
OK
<Setting range and default value of each set value>
Item Display
A (0:YES 1:NO)
NOTE: Even though the control is allowed, the CE mark support
control may not be executed depending on the power fre-
quency, etc.
<Initial value and set value linked with the destination>
Destination
U.S.A
CANADA
INCH
JAPAN
AB_B
EUROPE
U.K
AUS.
AB_A
CHINA
SIMULATION NO.26-30
TEST
CE MARK CONTROL SETTING
A:
1
[ 0~ 1]
26-35
Purpose
Function (Purpose) Used to set the trouble memory saving pro-
0
Section
Item
Operation/Procedure
1) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
2) When [OK] button is pressed, the current entered value is
saved to EEPROM and RAM.
* When [COLOR], or [BLACK] key is pressed, the current set
OK
value is saved to EEPROM and RAM.
<Setting range and default value of each set value>
Item Display
A (0:ONCE
1:ANY)
Setting
Content
range
0 CE mark 0 to 1
control allowed
1 CE mark
control inhibited
Setting value
1 (CE not supported)
1 (CE not supported)
1 (CE not supported)
1 (CE not supported)
1 (CE not supported)
0 (CE supported)
0 (CE supported)
0 (CE supported)
0 (CE supported)
0 (CE supported)
(0:YES 1:NO)
A 1
Setting
cedure.
—
—
Content
0 Only once. If same as the
previous one, it is not saved.
1 Any time. Though same as
the previous one, it is saved.
Default value
Refer to <Initial
value and set
value linked with
the destination>.
0
CLOSE
OK
Setting Default
range value
0 to 1 0