Sharp MX-3500N Service Manual page 162

<Set range and default value of each setup>
Item Display items
A NN_120_ WUP_HL_UM&HL_E
B NN_120_WUP_HL_LM
C LL_120_ WUP_HL_UM&HL_E
D LL_120_WUP_HL_LM
E HH_120_ WUP_HL_UM&HL_E
F HH_120_WUP_HL_LM
G ON_120_WUP_HL_UM
H ON 120 WUP HL_E
I NN_120_ FUS_DUP_HL_UM & HL_E
J NN_120_ FUS_DUP_HL_LM
K LL_120_ FUS_DUP_HL_UM&HL_E
L LL_120_ FUS_DUP_HL_LM
M HH_120_ FUS_DUP_HL_UM&HL_E
N HH_120_ FUS_DUP_HL_LM
O NN_120_ FUS_DUP_CNT
P LL_120_ FUS_DUP_CNT
Q HH_120_ FUS_DUP_CNT
R COOL_DOWN_HEAVY
S COOL_DOWN_OHP
T COOL_DOWN_DEVELOP
U WUP DUP TIME
V FUS MOTOR
* On adjustment values
Each temperature correction value → Temperature 1°C change
by 1 count
Each paper exit count → 1 sheet by 1 count
Each cool-down time → 1s change by 1 count
<Code descriptions of the above list>
TH_UM Fusing upper thermister MAIN center
TH_LM Fusing lower thermister MAIN
TH_E Fusing thermister external
HL_UM Heater lamp upper MAIN
HL_LM Heater lamp lower MAIN
HL_E Heater lamp external
SIMULATION NO.43.-24
TEST
FUSER TEMP RESET
A 50
A: 50
B 50
C 50
1 99
D 50
WARMUP end temperature
correction value
Temperature correction value
immediately after completion of
warm-up and during continuation
of temperature correction
Fusing temperature correction
value
Fusing duplex paper exit count
Cool-down time
Temperature correction
continuation time immediately
after completion of warm-up
Fusing web motor operation
interval
CLOSE
NN_120_ WUP_HL_UM&HL_E
NN_120_WUP_HL_LM
LL_120_ WUP_HL_UM HL_E
LL_120_WUP_HL_LM
MX3500N SIMULATION 7 – 54
Item descriptions
120°C or below when turning
on the power under NN
environment
120°C or below when turning
on the power under LL
environment
120°C or below when turning
on the power under HH
environment
120°C or below when turning
on the power
120°C or below when turning
on the power under NN
environment
120°C or below when turning
on the power under LL
environment
120°C or below when turning
on the power under HH
environment
Applicable number of sheets for SIM43-24-I, J (NN
Applicable number of sheets for SIM43-24-K, L (LL
Applicable number of sheets for SIM43-24-M, N (HH
Cool-down time (Heavy paper → Ready)
Cool-down time (OHP → Ready)
Cool-down time (Envelope → Ready)
Applicable time for SIM43-24-G, H (Timer from
completion of ready)
Web motor operation interval
43-31
Purpose
Function (Purpose) Used to check the operation of the fusing
Section
Item
Operation/Procedure
1) Remove the fusing unit.
2) Enter the simulation mode with the door open, and press
[EXECUTE] button.
3) Perform the fusing web cleaning motor drive (continuous rota-
tion for 10 sec). After completion, "COMPLETE" is displayed.
0
SIMULATION NO.43-31
TEST
FUSER WEB CLEANING CHECK
OK
Item Sim. 43-1-A, C
Item Sim. 43-1-B
Item Sim. 43-20-A, C
Item Sim. 43-20-B
Item Sim. 43-21-A, C
Item Sim. 43-21-B
Item Sim. 43-1-A
Item Sim. 43-1-C
Item Sim. 43-4-A, C,
E, G
Item Sim. 43-4-B, F
Item Sim. 43-22-A,
C, E, G
Item Sim. 43-22-B, F
Item Sim. 43-23-A,
C, E, G
Item Sim. 43-23-B, F
environment)
environment)
environment)
Operation check
web cleaning motor.
Fusing
Operation
Set Default
range value
1 to 99 50
1 to 99 50
1 to 99 55
1 to 99 60
1 to 99 50
1 to 99 50
1 to 99 60
1 to 99 55
1 to 99 55
1 to 99 50
1 to 99 60
1 to 99 50
1 to 99 50
1 to 99 50
1 to 60 5
1 to 60 10
1 to 60 5
1 to 60 15
1 to 60 30
1 to 60 40
0 to 255 120
1 to 20 6
0
CLOSE
1/1
EXECUTE