Sharp MX-3500N Service Manual page 139

Display items Item descriptions
AT DEVE ADJ_H_K Automatic developer
(MX-4500N/4501N only) adjustment value at
high speed
AT DEVE VO_L_K Automatic developer
adjustment control
AT DEVE VO_L_C
voltage at low speed
AT DEVE VO_L_M
AT DEVE VO_L_Y
AT DEVE VO_M_K Automatic developer
adjustment control
AT DEVE VO_M_C
voltage at middle speed
AT DEVE VO_M_M
AT DEVE VO_M_Y
AT DEVE VO_H_K Automatic developer
(MX-4500N/4501N only) adjustment control
voltage at high speed
TCD_K Toner concentration sensor K
TCD_C Toner concentration sensor C
TCD_M Toner concentration sensor M
TCD_Y Toner concentration sensor Y
TCV_K Toner concentration control K
TCV_C Toner concentration control C
TCV_M Toner concentration control M
TCV_Y Toner concentration control Y
SIMULATION NO.25-02
TEST
AUTOMATIC DEVELOPER ADJUSTMENT
128 AT DEVE VO_L_K
:
AT DEVE ADJ_L_K
: 128
AT DEVE ADJ_L_C AT DEVE VO_L_C
128
:
AT DEVE ADJ_L_M AT DEVE VO_L_M
: 128
AT DEVE ADJ_L_Y
AT DEVE VO_L_Y
K
C M
Y
26
26-1
Purpose Setting
Function (Purpose) Used to set the paper exit tray (MX-TRX1).
Section Paper exit
Item Setting
Operation/Procedure
1) Enter the set value with 10-key.
2) Press [OK] button to save the entered content in step 1).
Item Display
A (0:YES 1:NO) 0 Escape tray YES
1 Escape tray NO
SIMULATION NO.26 01
TEST
ESCAPE TRAY SETUP
A 0
(0:YES 1:NO)
A: 0
0 1
Display Default
range value
1 – 255 128
1 – 255 128
1 – 255 128
1 – 255 128
1 – 255 128
1 – 255 128
1 – 255 128
1 – 255 128
1 – 255 128
1 – 255 128
0
CLOSE
128
:
: 128
128
:
: 128
EXECUTE
1/2
Set
Content Default
range
0 to 1 1 (NO)
CLOSE
OK
MX3500N SIMULATION 7 – 31
26-2
Purpose
Function (Purpose) Used to set the paper size of the large
Section
Item
Operation/Procedure
Select the paper size with the buttons on the touch panel.
LCC
SIMULATION NO.26-02
TEST
SIZE SETUP
LCC
26-3
Purpose
Function (Purpose) Used to set the specifications of the auditor.
Section
Item
Operation/Procedure
Select the set target with the button on the touch panel.
When a button is pressed, the set content is saved.
Button
Item
display
BUILT-IN P10
AUDITOR
EC1
OUTSIDE NONE
AUDITOR
P VENDOR1
P OTHER
DOC ADJ ON
OFF
0
PF ADJ ON
OFF
VENDOR MODE1
MODE (*)
MODE2
MODE3
Setting
capacity tray (LCC). (When the paper size
is changed, this simulation must be exe-
cuted to change the paper size in software.)
Paper feed
Setting
0 8.5 x 11 (Default: U.S.A, Canada, Inch)
1 A4 (Japan, AB_B, Europe, U.K,
Australia, AB_A)
2 B5
A4
8.5 11
Setting
Auditor
Specifications
Content
Built-in auditor mode
(standard mode) operation
The built-in auditor mode is
changed to EC1.
Normal operation
Vendor mode for old-type coin
vendor. Control in the copy
mode only.
Vendor mode for the other
external auditor connected to
the coin vendor I/F
Document filing function
enabled
Document filing function
disabled
Continuous paper feed is
performed.
Continuous paper feed is not
performed.
Vendor mode 1
Vendor mode 2
Vendor mode 3
0
CLOSE
B5
1/1
Default
P10
NONE
OFF
OFF
MODE3