Cleaning & Maintenance - Procom FBN280RHAC Series Owner's Operation And Installation Manual

Set temperature: Press "Temp"
a.
button, then press or
room temperature. Burner will operate
to maintain set room temperature.
Fig13 Control
b. Set blower: Press "FAN" button. the
blower will shift between "AUTO" and
"OFF" option.
W hen "FAN" is in "AUTO" select: the
blower will be oprate depend on the tem-
perature inside the heater. and automati-
cally turn ON or OFF.
When Fan is in "OFF" select the blower
will not operate.
OPERATIONS OF
TIMER
A uto o ff: w hen t h e bu rner is in
operation, press TIMER button. Then
▼
press or to change to the sched-
uled time, then press the TIMER button
again, the TIMER starts timing and the
TIMER will flash and the green opera-
tion light flashes. Burner will automati-
cally shut off at set time.
LOCKING REMOTE
CONTROL
( child proof )
1. To Lock: Press
symbol will appear on control board.
2. To Unlock: Press LOCK button and
hold until lock image shows
locked (typically 6 secs.).
Fig14 "AUTO" select
OPERATING HEATER
to set desired
▼
CONTROL SYSTEM OPERATING
We provide the manual override con-
trol system in the event of power
outage.
Install battery for manual Ignitor:
1. Unscrew the ignitor cap.
2. Insert a AAA type battery with its
anode ("+") pointing out.
3. Screw the ignitor cap back.
board
Note: W e recommend that the battery
be taken out of the ignitor when the
power supply resumes.
LIGHTING INSTRUCTIONS
If power is off, you can operate the
fireplace manually.
1. STOP! Read the safety information
on page 11.
2. Check that gas supply to heater is
on.
3. Open bottom front access panel.
4. With Control Knob in the on ELEC-
TRIC position, press in the Control
Knob and turn counterclockwise to
OFF position.
NOTE: Knob cannot be turned
from PILOT/IGN to "OFF" unless
knob is pushed in slightly. Do not
force.
5. Wait five (5) minutes to clear out
any gas. Then smell for gas,
including near the floor. If you smell
gas, STOP! Follow "B" in the safety
information on page 11. If you do
not smell gas, go to the next step.
LOCK button , a
6. Push in gas control slightly and turn
counterclockwise to PILOT/IGN
and depress for five (5) seconds.
un-
NOTE: The first time that the heater
is operated after connecting the
gas supply, the control knob should
be depressed for about thirty (30)
seconds. This will allow air to
bleed from the gas system.
7. With Control Knob pressed in,
push ignitor button. This will light
the pilot. If needed, keep ignitor
button until pilot lights.
Continued
MANUAL OVERRIDE
INSTRUCTIONS
12
8. Keep Control Knob depressed for
ten (10) seconds after lighting
pilot. If pilot goes out, repeat steps
6, 7 and 8.
9. Turn counterclockwise to "ON"
position. Do not operate between
locked positions.
TO TURN OFF GAS
TO APPLIANCE
Shut off heater
Push in gas Control Knob slightly
and turn clockwise
position. Do not force.
W hen electric power is available and
electric operation is desired, turn
clockwise to OFF position for
one minute to allow the electronic
module to reset before starting. Then
press down knob and rotate clock-
wise to ELECTRIC position.
Do not operate between locked
positions.
MANUAL LIGHTING
PROCEDURE
(match light)
1. Open front door.
2. Follow steps 1 through 5 under
MANUAL OPERATING Lighting
Instructions.
3. With Control Knob in PILOT/IGN
position, strike match, and hold
near pilot. Press in Control Knob,
pilot should light.
4. Keep Control Knob pressed in for
30 seconds after lighting pilot.
After 30 seconds, release Control
Knob. Follow step 9 under
MANUAL OVERRIDE CONTROL
SYSTEM OPERATING
INSTRUCTIONS.
INSPECTING BURNERS
Check pilot flame pattern and burner
flame patterns often.
TO TURN OFF GAS TO APPLIANCE
Shut off heater
1. Press the IGN/OFF button.(see fig-
ure 15)
2. Set the ON/ OFF Switch position or
unplug the electric power to the heater.
to the OFF