Technical Data; Before Putting The Machine Into Operation; Assembly - Power Craft PMS 210/1 User Manual & Warranty

Anleitung_PMS_210-1_SPK7:_

5. Technical data

Asynchronous motor
Power rating
Operating mode
Idle speed n
0
Carbide saw blade
Number of teeth
Standing area
Tilting range
Mitre cuts
Saw bed support
Sawing width at 90°
Sawing width at 45°
Sawing width at 2 x 45°
(double mitre cuts)
6. Before putting the machine into
operation
The machine has to be set up where it can stand
firmly, e.g. bolt it to a work bench, a universal
base or similar.
All the covers and safety devices have to be
properly fitted before the machine is switched on.
It must be possible for the saw blade to run
freely.
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machineʼs moving parts run smoothly.
Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
Helpline No. UK / Northern Ireland 0151 649 1500 Rep. Ireland 189 094 6244
Model Number: PMS 210/1
11.06.2007 14:45 Uhr

7. Assembly

A.) Adjusting the saw (Fig. 4)
230 V ~ 50 Hz
To adjust the turntable (8), loosen the locking grip
1200 W
(10) by turning it through 2 complete rotations to
unlock the turntable (8).
S1
The turntable (8) can be set to 0°, 15°, 22.5°, 30°
5000 rpm
and 45°.
As soon as the turntable (8) has engaged, the
ø 210 x ø 30 x 2,5 mm
position must be fixed by tightening the locking
24
grip (10).
If different angles are required, the turntable (8) is
390 x 300 mm
fixed using the locking grip (10) alone.
-45° / 0° / +45°
While pressing down lightly on the machine head
(4), pull the lock pin (16) out of the motor holder
0° to 45° to the left
to disengage the saw from its bottom working
385 x 140 mm
position.
Swing up the machine head until the retaining
120 x 60 mm
hook latches home.
80 x 65 mm
The machine head (4) can be tilted by max. 45°
to the left by loosening the tensioning screw (13).
Check that the voltage marked on the rating plate
80 x 35 mm
is the same as your mains voltage and connect
up the machine.
The clamping device (22) and the workpiece
support (23) can be fastened on both the right
and left sides of the base plate (9).
B.) Adjusting the fence (Fig. 5/6)
Disconnect from the mains.
Move the saw head (4) into the 90° position and
tighten the locking grip (10).
Push down the saw head (4).
Place the angle with the long grip against the
fence, as shown in the illustration.
Check whether the saw blade (5) is perpendicular
to the fence (7).
If the position has to be corrected, loosen the two
fixing screws (13) of the fence (7) and adjust the
fence (7) so that it is perpendicular to the saw
blade (5).
Once you have completed the adjustment work,
retighten the two fixing screws (13).
C.) 90° cross-cuts and 0° rotary table (Fig. 1/2)
Press the main switch (3) to turn on the saw.
Important! The material to be cut must be
placed flat on the machining table to that it
cannot slip during cutting.
After switching on the saw, wait for the blade (5)
to reach its maximum speed.
Turn the release button (1) clockwise and,
holding the handle (2), lower the machine head
smoothly down through the workpiece applying
slight pressure.
Seite 10
10