Technical Data; Before Putting The Machine Into Operation; Assembly - Power Craft PSMS 2100 User Manual & Warranty

Anleitung PSMS 2100 SPK7:_

5. Technical data

Asynchronous motor
Output
Operating mode
Idle speed n
0
Carbide-tipped saw blade
Number of teeth
Tilting range
Mitre cuts
Sawing width at 90°
Sawing width at 45°
Sawing width at 2 x 45° (double mitre cuts)
Weight
Laser class
Laser wave length
Laser output
Laser power supply
6. Before putting the machine into
operation
The machine must be firmly mounted in working
position, e.g. on a workbench, the base frame
supplied with the machine, or similar.
All the covers and safety devices have to be
properly fitted before the machine is switched on.
It must be possible for the saw blade to run
freely.
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machineʼs moving parts run smoothly.
Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
25.01.2007 16:37 Uhr

7. Assembly

7.1 Setting up the saw unit (Fig. 1/2)
230 V~ 50 Hz
To adjust the turntable (8), loosen the locking
1700 W
handle (10) by approx. 2 turns, which frees the
turntable (8).
S1
Turn the turntable (8) and scale pointer (11) to
4800 min -1
the desired angular setting on the dial (12) and
ø 210 x ø 30 x 2,8 mm
lock into place with the locking handle (10).
Lightly press the machine head (4) down while at
24
the same time pulling the retaining pin (16) out
-45° / 0° / +45°
from the motor mounting; this causes the saw to
0° to 45° to the left
move down to the lower working position.
Swing the machine head (4) up until the retaining
205 x 65 mm
hook (1) latches into place.
145 x 65 mm
The clamping device (19) and the workpiece
support (20) can be fastened on both the right
and left sides of the base plate (9).
145 x 40 mm
By loosening the tightening screw (13), the
13,3 kg
machine head (4) can be angled to the left up to
2
45°.
650 nm
7.2 Making 90° crosscuts with turntable at 0°
≤ 5 mW
(Fig. 1/3)
2 x 1,5 V (AAA) For cutting widths up to 100 mm it is possible to fix
the sawʼs drag function with the knurled screw (14) in
rear position. If the cutting width exceeds 100 mm
you must ensure that the knurled screw (14) is
slackened and that the machine head (4) can be
moved.
Bring the machine head (4) to its upper position.
Push the machine head (4) back by its handle (2)
and affix in this position if necessary (depending
on the cutting width).
Place the piece of wood to be cut against the
stop rail (7) and on the turntable (8).
Secure the workpiece in position with the
clamping device (19) on the base plate (9) to
prevent the workpiece from moving during the
cutting process.
Turn the release lever (1) to the left to release
the machine head (4).
Push the ON/OFF switch (3) to start the motor.
Using the handle (2), push downward all the way
through the work-piece with uniform and light
pressure.
After the cutting process is finished, bring the
machine head back to its upper (home) position
and release the ON/OFF button (3).
Caution! The resetting springs in the machine
automatically raise the machine head. Do not
simply let go of the handle (2) after cutting, but
allow the machine head to slowly lift up by
applying slight counterpressure.
Seite 9
9