Power Craft PMS 210/1 User Manual & Warranty page 13

Anleitung_PMS_210-1_SPK7:_
When the cut is completed, return the machine to
its top parking position and let go of the On/Off
switch.
Caution! A return spring causes the machine
head to rise automatically at the end of the cut.
Do not let go of the handle (2) as soon as the cut
is completed but steady the machine head and
allow it to rise slowly.
D.) Precision adjustment of the stop for 90°
cross-cuts (Fig. 6/7)
Lower the machine head (4) and fix with the lock
pin (16).
Slacken the locking nut (12).
Place the stop angle between the saw blade
(5) and the rotary table (8).
Slacken the counter nut (29) and adjust the
setting screw (19) until the angle between the
saw blade (5) and the rotary table (8) equals 90°.
Re-tighten the counter nut (29) to fix the machine
in this setting.
Before you start work, check the position of the
angle display (11). If necessary, loosen the
pointer with a screwdriver for recessed head
screws and move it to the 0° position on the
angle scale (15). Then retighten the fixing
screws.
E.) 90° cross-cuts and 0°-45° rotary table (Fig.6)
The PMS 210/1 can be used to make angled cuts of
0°-45° relative to the stop rail on the left and right
side.
Turn the rotary table (8) by its handle (2) to the
angle you want, i.e. the mark on the rotary
table has to comply with the required angle
dimension (17) on the base plate (9).
Re-tighten the locking handle (10) in order to fix
the rotary table (8) in position.
Make the cut as described in Section C.).
F.) Mitre cuts 0°-45° and rotary table 0° (Fig. 6/9)
The PMS 210/1 can be used to make mitre cuts of
0°-45° relative to the machine bed on the left side.
Lift the machine head (4) to its top position.
Fix the rotary table (8) in 0° position.
Undo the locking nut (12) and, holding the handle
(2), tilt the machine head (4) to the left until the
pointer (11) coincides with the required angle
dimension (15).
Re-tighten the locking nut (12) and make the cut
as described in Section C.).
Helpline No. UK / Northern Ireland 0151 649 1500 Rep. Ireland 189 094 6244
Model Number: PMS 210/1
11.06.2007 14:45 Uhr Seite 11
G.) Precision adjustment of the stop for 45° mitre
cuts (Fig. 2/10)
Lower the machine head (4) and fix with the lock
pin (16).
Fix the rotary table (8) in 0° position.
Undo the locking nut (12) and, holding the handle
(2), tilt the machine head (4) to the left by 45°
Place the 45° stop angle between the saw
blade (5) and the rotary table (8).
Slacken the counter nut (24) and adjust the
setting screw (18) until the angle between the
saw (5) and the rotary table (8) equals exactly
45°.
H.) Mitre cuts 0°-45° and rotary table 0°-45°
(Fig. 11)
The PMS 210/1 can be used to make mitre cuts on
the left at an angle of 0°-45° relative to the work top
and 0°-45° relative to the stop rail.
Lift the machine head (4) to its top position.
Release the turntable (8) by loosening the locking
grip (10).
Adjust the rotary table (8) by its handle (2) to the
required angle (see also Section D).
Re-tighten the locking handle (10) to fix the rotary
table in position.
Undo the clamping nut (12) and, holding the
handle (2), tilt the machine head (4) to the left to
the required angle dimension
(see also Section F).
Re-tighten the clamping nut (12).
I.) Chip extraction (Fig. 2)
The saw is equipped with a chip collection bag (14).
The chip bag (14) can be emptied by opening the zip
fastener at the bottom.
J.) Replacing the saw blade (Fig. 2/3/4)
Always use the correct saw blade for the right
task.
Pull out the power plug.
Swing up the machine head (4).
Press the lever and swing up the saw blade
guard to the point where the recess in the saw
blade guard is above the flange bolt.
Press the saw shaft lock (26) with one hand while
holding the wrench (20) on the flange bolt (27)
with the other.
Firmly press on the saw shaft lock (26) and
slowly rotate the flange bolt (27) in clockwise
direction. The saw shaft lock engages after no
more than one rotation.
Now, using a little more force, slacken the flange
bolt in clockwise direction.
Turn the flange bolt until it is completely
removed.
11