User Mode Settings - Magicard Prima 2e Instruction Manual

Operation
(continued)

User mode settings

Main menu
> > C o u n t e r
> D i s p l a y >
Display mode > > C o n t r a s t
See p. 29
> > B a c k C o l o r
> C o u n t e r R e s e t
Counter reset mode
O K ?
For free counter resetting: press the ENTER button.
> C l e a n i n g >
Cleaning mode
For cleaning mode setting: Magnetic head and card feeder roller execution
> > I n k T y p e
> I n k >
> > B l a c k L e v e l
Ink mode
> > B l a c k M o d e
See p.31
> > S P - I n k 1 L e v e l
> > M e d i a T y p e
> R e t r a n s f e r >
> > Te m p . L e v e l
Retransfer mode
> > S p e e d ( F r o n t )
See p. 32
> > S p e e d ( B a c k )
> > M G P r i n t ( J I S )
> > S t a n d b y m o d e
Buzzer mode
> B u z z e r
Setting the buzzer ON/OFF: 2 settings [on
O n
Power saving mode
> P o w e r S a v i n g
Setting the time for the power saving mode:9 options [off, 5, 10, 15, 20, 25, 30, 45 and
O f f
> > Te m p . L e v e l
> B e n d R e m e d y >
> > S p e e d
See p. 34
Bend Remedy
> > C o o l i n g T i m e
mode
Card tickness setting mode:
> C a r d T h i c k n e s s
Card thickness setting: 2 options [Standard,Thin]
S t a n d a r d
Coercivity setting mode:
> M G I S O T y p e
ISO card coercivity setting:
H i - C o
Non-contact IC antenna setting mode:
> I C A n t e n n a P o s .
Non-contact IC antenna position setting: 3 options [None, Ext. Unit, Added on]
N o n e
IC contact position setting mode:
> I C C o n t a c t P o s .
IC contact position setting: 3 options [None, Built-in, Ext. Unit]
N o n e
> Te s t P r i n t Test print mode:
to carry out test printing:
O K ?
Unit No:
> U n i t N o :
Unit No. setting:
N o . 1
Transfer Mode:
> T r a n s p o r t m o d e
Transfer mode setting:
O K ?
28
4 counter type settings: [Total, Head, Free, Rollers]
To t a l
LCD panel contrast setting:
0 ( S t a n d a r d )
LCD pamel background color setting: 8 options
S K Y B L U E
Display on ink ribbon : the ink type being used is displayed
Display only because of automatic setting by RF-ID(Setting is not possible)
Y M C K : 0
Setting the black value K:
0 ( S t a n d a r d )
Setting the K printing mode: 2 options [standard and fine]
S t a n d a r d
> > S P - I n k 2 L e v e l
0 ( S t a n d a r d ) 0 ( S t a n d a r d )
Setting the retransfer film: setting the film type
[1000,750] - two types
S t d ( 1 0 0 0 / r o l l ) : 0
Setting the retransfer roller temperature: 6 gradations can be set from –3 to +2,
+ 1 ( H i g h )
Setting the retransfer speed:
+ 2 ( F a s t )
Setting the rear retransfer speed:
+ 2 ( F a s t )
Setting the way of peeling off the retransfer film: 2 settings [On and Off]
O f f
Stand by selection: In case of both side printing with optional unit connected,
select either one of the card sides for standby.2 Settings[Front Wait,Back Wait]
F r o n t W a i t
and off]
Bend remedy roller temperature setting: 7 gradations can be set from –5 to 0 or
O f f
Bend remedy speed setting:
+ 2 ( F a s t )
Cooling time setting:
N o n e
2 options [Lo-Co
and Ho-Co]
press the ENTER button.
7 options [No.1 to No.7]
press the ENTER button.
press the ENTER button.
Submenu
7 gradations from –3 to +3, the higher
the value the stronger the contrast.
See p. 30
9 gradations can be set from –3 to +5, the
larger the value the darker the printing.
Setting the special ink SP-Ink 1, SP-Ink2 darkness:
9 gradations can be set from –3 to +5, the larger the value
the darker the printing.
the larger the value the higher the
temperature.
13 gradations can be set from –10 to +2,
the larger the value the faster the speed.
13 gradations can be set from –10 to +2, the
larger the value the faster the speed.
See p. 33
60] (units: minutes)
off, the larger the value the higher
the temperature.
5 gradations can be set from –2 to +2, the
larger the value the faster the speed.
16 gradations can be set: none and 1–15 (units
seconds).
See p. 34
See p. 35
Factory setting
Total
0
SKY BLUE
See p. 30
0
Standard
0
Standard
(1000/roll):0
+1
+2
+2
Off
Front Wait
On
See p. 33
Off
Off
+2
None
Standard
Hi-Co
See p. 35
See p. 35
See p. 35
No.1
See p. 35
See p. 35