Motorola Netopia Administrator's Handbook
  1. Manuals
  2. Brands
  3. Motorola Manuals
  4. Gateway
  5. Netopia
  6. Administrator's handbook

Motorola Netopia Administrator's Handbook

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Administrator's
Handbook
®
Motorola Netopia
Embedded Software
Version 9.0.1
Motorola Netopia
September 2010
®
Gateways

Advertisement

Table of Contents
loading

Related Manuals for Motorola Netopia

Summary of Contents for Motorola Netopia

  • Page 1 Administrator’s Handbook ® Motorola Netopia Embedded Software Version 9.0.1 Motorola Netopia ® Gateways September 2010...
  • Page 2 (such as translation, transformation or adaptation) without written permission from Motorola, Inc. Motorola reserves the right to revise this publication and to make changes in content from time to time without obligation on the part of Motorola to provide notification of such revision or change. Motorola provides this guide without warranty of any kind, either implied or expressed, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.

  • Page 3: Table Of Contents

    Table of Contents Table of Contents ® Setting up Your Motorola Netopia Modem or Gateway CHAPTER 1 Important Safety Instructions ......8 POWER SUPPLY INSTALLATION.
  • Page 4 Administrator’s Handbook Factory Reset Switch ....... . 49 Command Line Interface .
  • Page 5 Table of Contents Electrical Safety Advisory ......87 Warranty Information ....... . 88 Software License, Limited Warranty and Limitation of Remedies .
  • Page 6 Administrator’s Handbook...

  • Page 7: Setting Up Your Motorola Netopia Modem Or Gateway

    ® CHAPTER 1 Setting up Your Motorola Netopia Modem or Gateway ® This Administrator’s Handbook covers the advanced features of the Motorola Netopia Modem and Gateway fam- ilies. ® Your Motorola Netopia equipment offers advanced configuration features accessed through the Web-based interface screens and the Command Line Interface (CLI).

  • Page 8: Important Safety Instructions

    Administrator’s Handbook Important Safety Instructions POWER SUPPLY INSTALLATION ® Connect the power supply cord to the power jack on the Motorola Netopia Gateway. Plug the power supply into an appropriate electrical outlet. ☛ WARNING: The power supply must be connected to a mains outlet with a protective earth connection.

  • Page 9: Wichtige Sicherheitshinweise

    Wichtige Sicherheitshinweise NETZTEIL INSTALLIEREN ® Verbinden Sie das Kabel vom Netzteil mit dem Power-Anschluss an dem Motorola Netopia Gateway. Stecken Sie dann das Netzteil in eine Netzsteckdose. ☛ Warnung: Das Netzteil muss an eine Steckdose, die mit einem Schutzleiter verbunden ist, angeschlos- sen werden.

  • Page 10: Set Up Your Gateway

    Set up your Gateway ® Refer to your User Manual for instructions on how to connect your Motorola Netopia Gateway to your power source, PC or local area network, and your Internet access point, whether it is a dedicated DSL outlet or a DSL or ®...

  • Page 11: Configure Your Pc For Dynamic Addressing

    Select Obtain an IP address automatically. Select Obtain DNS server address automatically, if available. Remove any previously configured gateways, if applicable. Click the OK button. Restart if prompted. “Motorola Netopia® Gateway Quickstart” on page 14 Proceed to the next section...
  • Page 12 Administrator’s Handbook c. Windows Vista and Windows 7 are set to obtain an IP address automatically by default. You may not need to configure them at all. To check, open the Networking Control Panel and select Internet Protocol Version 4 (TCP/IPv4). Click the Properties button.
  • Page 13 Preferences -> like this: Network -> Configure Then go to Step 2. Select Built-in Ethernet Select Configure IPv4: Using DHCP Close and Save, if prompted. “Motorola Netopia® Gateway Quickstart” on page 14 Proceed to the next section...

  • Page 14: Motorola Netopia ® Gateway Quickstart

    Motorola Netopia Gateway’s configuration pages. ◆ ® For security, you may create and enter an Administrative password for accessing the Motorola Netopia Gate- way. • The administrative User name is admin. • The initial Password can be whatever you choose, from one to 32 characters long.
  • Page 15 Internet bookmarks. Optional services that you may have contracted with your provider are also available. ® If you have any questions or encounter problems with your Motorola Netopia Gateway, refer to “Basic Trouble- shooting”...
  • Page 16 Administrator’s Handbook...

  • Page 17: Web-Based Device Management

    CHAPTER 2 Web-based Device Management ® Using the Web-based user interface for the Motorola Netopia Gateway you can configure, troubleshoot, and monitor the status of your Gateway. ◆ “The Home Page” on page 18 ◆ “Links Bar” on page 19 ◆...

  • Page 18: The Home Page

    Administrator’s Handbook The Home Page Home Page for a Wi-Fi model Home Page Information The Home page displays information about the following categories: ◆ Connection Information ◆ Router Information ◆ Local Network ◆ Restart Connection – For a PPPoE connection, clicking this button will bring down any PPPoE WAN connec- tion that is up and resend your current PPPoE login credentials and reestablish your Internet connection.

  • Page 19: Links Bar

    Links Bar The links in the left-hand column of the Home page access a series of pages to allow you to monitor, diagnose, and update your Gateway. The following sections give brief descriptions of these pages. ◆ “The Home Page” on page 18 ◆...

  • Page 20: Configure

    Administrator’s Handbook Configure Configure When you click in the left hand column of links, the links bar expands. ◆“Connection” on page 21 ◆“DHCP Server” on page 23 ◆“More IP Subnets” on page 24 ◆“Wireless” on page 25 ◆“NAT” on page 31 ◆“Router Password”...

  • Page 21: Connection

    Encapsulation: The authentication and encapsulation protocol is determined by your ISP by the type of account that you have signed up for and the model of your Motorola device. Choose from the pull-down menu: pppoe-llc, pppoe-vcmux, ether-llc, ip-llc, pppoa-llc, or pppoa-vcmux ◆...
  • Page 22 Administrator’s Handbook ◆ The screen expands to allow you to enter the Static IP Address and Netmask from your Service Provider in the appropriate fields. ◆ IP Gateway: The IP Address of the default gateway, or peer address if using PPP. This is normally set to 0.0.0.0 for PPP connections.

  • Page 23: Dhcp Server

    DHCP Server DHCP Server When you click , the DHCP Server Configuration page appears. The Server configuration determines the functionality of your DHCP Settings. This functionality enables the Gate- way to assign your LAN computer(s) a “private” IP address and other parameters that allow network communica- tion.

  • Page 24: More Ip Subnets

    Administrator’s Handbook More IP Subnets More IP Subnets When you click the link, the Additional IP Subnets screen appears. One subnet is preconfigured by default. The Additional IP Subnets screen allows you to configure up to seven secondary subnets and their DHCP ranges, by entering IP address/subnet mask pairs: ☛...

  • Page 25: Wireless

    Wireless (supported models) Wireless When you click the link in the links bar, the menu expands. Wireless Configuration Base Settings When you click the link, the Wireless Base Settings page appears. ◆ The wireless function is automatically enabled by default. If you uncheck the Enabled checkbox, the wireless options are disabled, and the Gateway will not provide or broadcast its wireless LAN services.
  • Page 26 Administrator’s Handbook ☛ NOTE: , or If you choose to limit the operating mode to G-only N-only A-only B-only, clients using the mode(s) you excluded will not be able to connect. ◆ Channel – (1 through 11, for North America) on which the network will broadcast. This is a frequency range within the 2.4Ghz band.
  • Page 27 Gateway. ® In addition, if you have enabled WEP or WPA encryption on the Motorola Netopia Gateway, your network clients must also have WEP or WPA encryption enabled, and must have the same WEP or WPA encryption key as the ®...
  • Page 28 Administrator’s Handbook Any WEP-enabled client must have an identical key of the same length as the Gateway, in order to successfully receive and decrypt the traffic. Similarly, the client also has a ‘default’ key that it uses to encrypt its transmissions. In order for the Gateway to receive the client’s data, it must likewise have the identical key of the same length.
  • Page 29 Wireless Multi-media Configuration Wireless Multi-media is an advanced feature that allows you to prioritize various types of data travelling over the wireless network. Certain types of data that are sensitive to delays, such as voice or video, must be prioritized ahead of other, less delay-sensitive types, such as email.
  • Page 30 Administrator’s Handbook ◆ You add wireless clients that you want to either authorize or exclude for your wireless LAN by entering the MAC addresses in the MAC Address field provided. Add this MAC Click the button. Your entries will be added to a client MAC Filter List. Apply Changes Click the button.

  • Page 31: Nat

    When you click , the NAT Configuration page appears. ◆ NAT Configuration allows you to host internet applications when NAT is enabled. You can host different games and software on different PCs. ◆ Pinhole Entry allows you to transparently route selected types of network traffic, such as FTP requests or HTTP (Web) connections, to a specific host behind the Gateway.
  • Page 32 Administrator’s Handbook The following example shows three pinholes: ◆ a web server (using TCP on port 80, the standard HTTP protocol web port) on a host at the internal IP address 192.168.1.1 ◆ a mail server (using TCP on port 25, the standard SMTP protocol email port) at the internal IP address 192.168.1.2 ◆...

  • Page 33: Router Password

    Motorola Netopia Gateway’s configuration pages. ◆ ® For security, you may create and enter an Administrative password for accessing the Motorola Netopia Gate- way. • The administrative User name is admin. • The Password can be whatever you choose, from one to 32 characters long.

  • Page 34: Time Zone

    Administrator’s Handbook Time Zone Time Zone When you click the link, the Time Zone page appears. You can set your local time zone by selecting your time zone from the pull-down menu. This allows you to set the time zone for general time stamp purposes. Apply Changes Click the button.

  • Page 35: Status

    Status Status When you click in the left hand column of links, the links bar expands. Available Status links vary by platform. When you click , the DSL Statistics page appears. The DSL Statistics page displays information about the Gateway's WAN connection to the Internet. ◆...

  • Page 36: Ethernet

    Administrator’s Handbook Ethernet Ethernet When you click , the Ethernet Statistics page appears. The Ethernet Statistics page: ◆ displays your Gateway's unique hardware (MAC) address. ◆ displays detailed statistics about your LAN data traffic, upstream and downstream. Wireless Wireless When you click , the Wireless Statistics page appears.

  • Page 37: System Log

    The file can be opened with your favorite text editor. ☛ Note: Some browsers, such as Internet Explorer for Windows XP, require that you specify the Motorola ® Netopia Gateway’s URL as a “Trusted site” in “Internet Options: Security”. This is necessary to...

  • Page 38: Firewall Log

    The Gateway detects security related events including common types of malicious attacks and writes them to a dedicated Firewall log file. You view this log file from either: ◆ ® Motorola Netopia Web interface ◆ Text-based command line interface using telnet The log provides information useful in identifying a specific type of attack and tracing its origin.

  • Page 39: Utilities

    Utilities Utilities When you click the link, the linksbar expands to display the Gateway’s diagnostic and update utilities. ◆ “Diagnostics” on page 40 ◆ “Restart Router” on page 42 ◆ “Reset Router” on page 42 ◆ “Update Router” on page 43...

  • Page 40: Diagnostics

    Administrator’s Handbook Diagnostics Diagnostics When you click , the Diagnostics page appears. This automated multi-layer test examines the functionality of the Gateway from the physical connections to the data traffic being sent by users through the Gateway. Run Full Diagnostics section tests a number of different things at the same time, including the DSL line, the Ethernet interface and the PPPoE session.
  • Page 41 PASS Check IP connect to PPP (vcc1) PASS Pinging Gateway PASS ==== Checking Miscellaneous Check DNS- Query for netopia.com : SKIPPED Ping DNS Server Primary IP Address : SKIPPED TEST DONE Each test generates one of the following result codes:...

  • Page 42: Restart Router

    Administrator’s Handbook Restart Router When the Gateway is restarted, it will disconnect all users, initialize all its interfaces, and copy the Operating Sys- tem Software from its internal storage. When you make configuration changes, you must restart for the changes to take effect. Reset Router You might need to reset your Gateway to its factory default state, and clear all of your previous settings.

  • Page 43: Update Router

    To update your software from a file on your PC, you must first download the software. Click the link. Click here to download You will be taken to the Motorola website for software upgrades. If an upgrade exists, download it to your computer. Browse your computer for the operating system file you downloaded. Click the button.

  • Page 44: Help

    Administrator’s Handbook Help Help Click the link in the left-hand column of links to display a page of explanatory information. Help is available for every page in the Web interface. Here is an example:...

  • Page 45: Chapter 3 Basic Troubleshooting

    CHAPTER 3 Basic Troubleshooting This section gives some simple suggestions for troubleshooting problems with your Gateway’s initial configura- tion. Before troubleshooting, make sure you have ◆ read the User Manual; ◆ plugged in all the necessary cables; and ◆ set your PC’s TCP/IP controls to obtain an IP address automatically.

  • Page 46: Status Indicator Lights

    Administrator’s Handbook Status Indicator Lights The first step in troubleshooting is to check the status indicator lights (LEDs) in the order outlined in the following section. Motorola Netopia® Gateway 2247-N8 status indicator lights Front View Power Activity Ethernet 1, 2, 3, 4...

  • Page 47: Led Function Summary Matrix

    LED Function Summary Matrix Power Internet Unlit No power No signal Not connected Green Solid Power on DSL line synched with the Connected to the Internet DSLAM Green Flashing Activity on the DSL cable Transmitting or receiving data on the WAN port Solid System malfunction Flashing...
  • Page 48 Administrator’s Handbook ◆ Make sure the you are using the Ethernet cable, not the DSL cable. The Ethernet cable is thicker than the standard telephone cable. ◆ Make sure the Ethernet cable is securely plugged into the Ethernet jack on the PC. ◆...

  • Page 49: Factory Reset Switch

    Factory Reset Switch Lose your password? This section shows how to reset the Motorola Netopia® so that you can access the configu- ration screens once again. ☛ NOTE: Keep in mind that all of your settings will need to be reconfigured.
  • Page 50 Administrator’s Handbook...

  • Page 51: Chapter 4 Command Line Interface

    The Motorola Netopia® Gateway operating software includes a command line interface (CLI) that lets you access your Motorola Netopia® Gateway over a telnet connection. You can use the command line interface to enter and update the unit’s configuration settings, monitor its performance, and restart it.

  • Page 52: Overview

    Administrator’s Handbook Overview The CLI has two major command modes: SHELL and CONFIG. Summary tables that list the commands are pro- vided below. Details of the entire command set follow in this section. SHELL Commands Command Status and/or Description to send ARP request atmping to send ATM OAM loopback clear...
  • Page 53 CONFIG Commands Command Verbs Status and/or Description delete Delete configuration list data help Help command option save Save configuration data script Print configuration data Set configuration data validate Validate configuration settings view View configuration data Keywords conn Connection options TCP/IP protocol options Domain Name System options igmp IGMP configuration options...

  • Page 54: Starting And Ending A Cli Session

    < ip_address > You must know the IP address of the Motorola Netopia® Gateway before you can make a telnet connection to it. By default, your Motorola Netopia® Gateway uses 192.168.1.254 as the IP address for its LAN interface. You can use a Web browser to configure the Motorola Netopia®...

  • Page 55: About Shell Commands

    SHELL Prompt When you are in SHELL mode, the CLI prompt is the name of the Motorola Netopia® Gateway followed by a right angle bracket (>). For example, if you open a CLI connection to the Motorola Netopia® Gateway named “Netopia- Netopia-3000/9437188>...

  • Page 56: Shell Commands

    IP address to an nnn.nnn.nnn.nnn Ethernet hardware address. clear [ yes ] Clears the configuration settings in a Motorola Netopia® Gateway. You are prompted to confirm the clear com- mand by entering yes. clear_certificate Removes an SSL certificate that has been installed.
  • Page 57 Adds the message in the message_string argument to the Motorola Netopia® Gateway diagnostic log. loglevel [ level ] Displays or modifies the types of log messages you want the Motorola Netopia® Gateway to record. If you enter loglevel command without the optional level argument, the command line interface displays the cur- rent log level setting.
  • Page 58 Rewinds the firewall log to the first entry. reset ipmap Clears the IPMap table (NAT). reset log Rewinds the diagnostic log display to the top of the existing Motorola Netopia® Gateway diagnostic log. The reset show log log command does not clear the diagnostic log. The next command will display information from the beginning of the log file.

  • Page 59: Show Crash

    Displays LAN devices that conform with the TR111 Gateway requirement. It displays - IP Address, Manufacture OUI and Serial number. show enet [ all ] Displays Ethernet interface statistics maintained by the Motorola Netopia® Gateway. Supports display of individ- ual LAN switch port statistics as well as WAN Ethernet statistics (where applicable). Example:...
  • Page 60 Displays the Ethernet address resolution table stored in your Motorola Netopia® Gateway. show ip igmp Displays the contents of the IGMP Group Address table and the IGMP Report table maintained by your Motorola Netopia® Gateway. show ip interfaces Displays the IP interfaces for your Motorola Netopia®...

  • Page 61: Show Log

    Displays the IP routes stored in your Motorola Netopia® Gateway. show ipmap Displays IPMap table (NAT). show log Displays blocks of information from the Motorola Netopia® Gateway diagnostic log. To see the entire log, you can show log show log all. repeat the...

  • Page 62: Wan Commands

    The TFTP server must be accessible on your Ethernet network. The server_address argument identifies the IP address of the TFTP server on which you want to store the Motorola Netopia® Gateway settings. filename argument identifies the path and name of the configuration file on the TFTP server. If you...
  • Page 63 [ vcc-id ] ® Renews the DHCP lease the Motorola Netopia Gateway is currently using to acquire the IP settings for the spec- vcc-id ified DSL port. The identifier is an “index”...

  • Page 64: About Config Commands

    CONFIG Mode Prompt When you are in CONFIG mode, the CLI prompt consists of the name of the Motorola Netopia® Gateway followed by your current node in the hierarchy and two right angle brackets (>>). For example, when you enter CONFIG config...

  • Page 65: Guidelines: Config Commands

    Enter IP addresses in dotted decimal notation (0 to 255). If a command is ambiguous or miskeyed, the CLI prompts you to enter additional information. For example, you must specify which virtual circuit you are configuring when you are setting up a Motorola Netopia® Gateway. Displaying Current Gateway Settings...

  • Page 66: Validating Your Configuration

    Error: Subnet mask is incorrect Global Validation did not pass inspection! You can use the validate command to verify your configuration settings at any time. Your Motorola Netopia® Gateway automatically validates your configuration any time you save a modified configuration.

  • Page 67: Config Commands

    If dhcp-server-enable is set to on, specifies the first address in the DHCP address range. The Motorola Netopia® Gateway can reserve a sequence of up to 253 IP addresses within a subnet, beginning with the specified address for dynamic assignment.

  • Page 68: Ip Dns Commands

    [ on | off ] ® Specifies whether you want the Motorola Netopia Gateway to use network address translation (NAT) when com- municating with remote Gateways. NAT lets you conceal details of your network from remote Gateways. It also permits all LAN devices to share a single IP address.

  • Page 69: Ip Igmp Commands

    Other uses include updating the address books of mobile computer users in the field, or sending out company newsletters to a distribution list. ® Since a router should not be used as a passive forwarding device, Motorola Netopia Gateways use a protocol for forwarding multicasting: Internet Group Management Protocol (IGMP).
  • Page 70 Administrator’s Handbook v1 routers are present on a network. IGMP forwarding is enabled per IP Profile and WAN Connec- tion Profile. ◆ Last Member Query Interval – the amount of time in tenths of a second that the IGMP gateway waits to receive a response to a Group-Specific Query message.

  • Page 71: Ntp Commands

    set ip igmp snoop-entry-time seconds The snoop-entry-time is the amount of time an entry will remain in the snooping table (in seconds) after being added. An entry is added when a "JOIN" is seen from a multicast client. Any new joins (triggered by upstream queries) will reset the timeout back to seconds.

  • Page 72: Application Layer Gateway (Alg) Commands

    Administrator’s Handbook Application Layer Gateway (ALG) commands These commands allow you to enable or disable the router’s support for a variety of Application Layer Gateways (ALGs). An application layer gateway (ALG) is a NAT component that helps certain application sessions to pass cleanly through NAT.

  • Page 73: Management Commands

    0-1024 are used by other protocols, you should use numbers in the range 1025-65534 when assigning new port numbers to the Motorola Netopia® Gateway telnet configuration interface. A setting of 0 (zero) will turn the server off.

  • Page 74: Physical Interfaces Commands

    0-1024 are used by other protocols, you should use numbers in the range 1025-65534 when assigning new port numbers to the Motorola Netopia® Gateway web configuration interface. A setting of 0 (zero) will turn the server off.
  • Page 75 set physical dsl profile-12b [ off | on ] Default is on. set physical dsl profile-17a [ off | on ] Default is on. set physical dsl profile-30a [ off | on ] Default is off. set physical dsl us0 [ off | on ] Default is on.

  • Page 76: Pppoe Relay Commands

    Administrator’s Handbook set physical dsl atm vcc 2 datapath [ phy0fast | phy0interleaved ] Sets the ATM datapath, Fast Path or Interleaved. Default is phy0fast. set physical dsl atm vcc 2 encap-type [ llcsnap-eth | llcsnap-rtip | llcencaps-ppp | vcmux-eth | vcmux-ipoa | vcmux-pppoa ] Specifies the data link encapsulation type.

  • Page 77: Nat Pinhole Commands

    NAT Pinhole commands NAT pinholes let you pass specific types of network traffic through the NAT interfaces on the Motorola Netopia® Gateway. NAT pinholes allow you to route selected types of network traffic, such as FTP requests or HTTP (Web) connections, to a specific host behind the Motorola Netopia®...

  • Page 78: System Commands

    “XXX” is the serial number of the device; for example, Netopia-7000/9437188. A system name can be 1 – 255 characters long. Once you have assigned a name to your Motorola Netopia® Gateway, you can enter that name in the Address text field of your browser to open a connection to your Motorola Netopia®...
  • Page 79 ◆ medium - Medium-level informational messages or greater; includes status messages that can help monitor network traffic. ◆ high - High-level informational messages or greater; includes status messages that may be significant but do not constitute errors. The default. ◆ alerts - Warnings or greater;...
  • Page 80 Administrator’s Handbook...

  • Page 81: Technical Specifications And Safety Information

    Description Communications interfaces: The Motorola Nteopia® Gateways have an RJ-11 jack for DSL line connections or an RJ-45 jack for cable/DSL modem connections and 1 or 4–port 10/100Base-T Ethernet switch for your LAN connections..Some models contain an 802.11b/g/n wireless LAN transmitter.

  • Page 82: Agency Approvals

    ◆ EMC Compatibility, 89/336/EEC, conforming to EN 55 022 This Motorola product is in conformity with the essential requirements and other relevant requirements of the Radio Equipment and Telecommunications Terminal Equipment Directive (R&TTE) 1999/5/EC, following the provision of the Electromagnetic Compatibility Directive (EMC) No. 89/336/EEC and Low Voltage Directive (LVD) No.

  • Page 83: Manufacturer's Declaration Of Conformance

    Company or to one of our authorized agents. Contact Us for US Technical Support for Hardware Products 1-877-466-8646 http://broadband.motorola.com/consumers/support/default.asp?supportSection=blank ☛ Important This product was tested for FCC compliance under conditions that included the use of shielded cables and connectors between system components.
  • Page 84 Administrator’s Handbook Declaration for Canadian users NOTICE: The Canadian Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operation, and safety requirements. The Department does not guarantee the equipment will operate to the user’s satisfac- tion.

  • Page 85: Important Safety Instructions

    Important Safety Instructions Australian Safety Information The following safety information is provided in conformance with Australian safety requirements: Caution DO NOT USE BEFORE READING THE INSTRUCTIONS: Do not connect the Ethernet ports to a carrier or car- riage service provider’s telecommunications network or facility unless: a) you have the written consent of the net- work or facility manager, or b) the connection is in accordance with a connection permit or connection rules.

  • Page 86: 47 Cfr Part 68 Information

    If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. ® g) If trouble is experienced with this equipment, the Motorola Netopia Gateway, for warranty information, please contact:...

  • Page 87: Electrical Safety Advisory

    This equipment not intended to be repaired by the end user. In case of any problems, please refer to the trou- bleshooting section of the Product User Manual before calling Motorola Technical Support. i) Connection to party line service is subject to state tariffs. Contact the state public utility commission, public ser- vice commission or corporation commission for information.

  • Page 88: Warranty Information

    The Software is never sold. Motorola licenses the Software to the original customer and to any subsequent lic- ensee for personal use only on the terms of this License. Motorola and its 3rd party licensors retain the ownership of the Software.

  • Page 89: Warranty Information

    Product for its installation and use. While every reasonable effort has been made to insure that you will receive a Product that you can use and enjoy, Motorola does not warrant that the functions of the Product will meet your requirements or that the operation of the Product will be uninterrupted or error-free.
  • Page 90 Product, whether made or suffered by you or another person and whether based in con- tract or tort. IN NO EVENT SHALL MOTOROLA BE LIABLE TO YOU OR ANY OTHER PARTY FOR ANY DIRECT, INDI- RECT, GENERAL, SPECIAL, INCIDENTAL, CONSEQUENTIAL, EXEMPLARY OR OTHER DAMAGES ARISING...

  • Page 91: Copyright Acknowledgments

    Copyright Acknowledgments Because Motorola has included certain software source code in this product, Motorola includes the following text required by the respective copyright holders: Portions of this software are based in part on the work of the following: Copyright (c) 1998-2005 The OpenSSL Project. All rights reserved.
  • Page 92 Administrator’s Handbook 3. Neither the name of the project nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE PROJECT AND CONTRIBUTORS ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
  • Page 93 2) No right is granted to use any trade name, trademark, or logo of Broadcom Corporation. Neither the “Broadcom Corporation” name nor any trademark or logo of Broadcom Corporation may be used to endorse or promote products derived from this software without the prior written permission of Broadcom Corporation. 3) THIS SOFTWARE IS PROVIDED “AS-IS”...
  • Page 94 Administrator’s Handbook Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.
  • Page 95 Notes: Some of the constants in this file are specific to Arcom's Target188EB hardware. This software can be easily ported to systems with different data bus widths by redefining ';datum';. Copyright (c) 1998 by Michael Barr. This software is placed into the public domain and may be used for any purpose. However, this notice must not be changed or removed and no warranty is either expressed or implied by its publication or distribution.
  • Page 96 Administrator’s Handbook A “library” means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables. The “Library”, below, refers to any such software library or work which has been distributed under these terms.
  • Page 97 b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at run time a copy of the library already present on the user's computer system, rather than copying library functions into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with.
  • Page 98 Administrator’s Handbook Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
  • Page 99 Portions of this software are based in part on the work of the following: Net SNMP License http://net-snmp.sourceforge.net/about/license.html Various copyrights apply to this package, listed in various separate parts below. Please make sure that you read all the parts. Up until 2001, the project was based at UC Davis, and the first part covers all code written during this time. From 2001 onwards, the project has been based at SourceForge, and Networks Associates Technology, Inc.
  • Page 100 Administrator’s Handbook Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. Neither the name of the Sun Microsystems, Inc. nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
  • Page 101 Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
  • Page 102 Administrator’s Handbook Portions of this software are based in part on the work of the following: Snprintf License Copyright Patrick Powell 1995 This code is based on code written by Patrick Powell (papowell@astart.com). It may be used for any purpose as long as this notice remains intact on all source code distributions.

  • Page 103: Caring For The Environment By Recycling

    Motorola, no lo de las prácticas vigentes en su región. Si no existen sistemas de recolección deseche junto con residuos resi- disponibles, solicite asistencia llamando el Servicio al Cliente de Motorola. denciales o comerciales. Recyclage de votre équipement Motorola Recyclage pour le Veuillez ne pas jeter ce produit avec vos ordures ménagères ou vos rebuts...

  • Page 104: Milieubewust Recycleren

    Jeśli w danym regionie wyrzucać do komunalnych pojem- nie istnieją systemy zbierania odpadów elektrycznych i elektronicznych, infor- ników na śmieci. macje o utylizacji należy uzyskać od biura obsługi klienta firmy Motorola (Motorola Customer Service). Reciclagem do seu equipamento Motorola Cuidando do meio Não descarte este produto junto com o lixo residencial ou comercial.
  • Page 105 경우, 가정 또는 상업 폐기물과 폐기물 항목을 수집하는 시스템이 구축되어 있습니다. 해당 지역에 함께 버리지 마십시오. 구축되어 있는 절차에 관한 정보는 지역 관할당국에 연락하십시오. 수집 시스템이 존재하지 않는 경우, 도움을 받기 위해 Motorola 고객서비스부로 연락하십시오. M ot or ol a Motorola Motorola http://www.motorola.com/recycle...
  • Page 106 Administrator’s Handbook...

  • Page 107: Index

    Index Ethernet Ethernet statistics Symbols !! command factory default Factory Reset Switch firewall Address resolution table Firewall Log Administrator password Arguments, CLI Command Help Home Page !! command ICMP Echo IGMP Arguments IGMP Snooping Command shortcuts Command truncation IP DNS commands Configuration mode IP Gateway commands Keywords...
  • Page 108 Administrator’s Handbook NAT Pinhole commands Trivial File Transfer Protocol NTP commands Troubleshooting Truncation Password Update Router Administrator User name User User password Physical interfaces commands Utilities Ping command Pinhole Entry Prompt, CLI View command view config quickstart Wi-Fi Protected Access Wired Equivalent Privacy Reset Router Wireless...

This manual is also suitable for:

Netopia series

Table of Contents