Specifications - 161Stl - Thermal Arc 201 TS Service Manual

SAFETY AND INSTALLATION

3.02 Specifications - 161STL

Power Source Part Number
Mains Power
Nominal Supply Voltage
Number of Phases
Input Voltage Range
Nominal Supply Frequency
Effective Input Current (l1eff)
Maximum Input Current (l1 max)
Single Phase Generator Requirements [Continuous rating
at nominal supply voltage with maximum output for STICK
(SMAW) welding]
Welding Output
Welding Current Range
Nominal DC Open Circuit Voltage (OCV)
Welding Output, 104º F (40º C), 10 min.
(Quoted figures refer to STICK (SMAW) output)
Rated Input Current (A)
Rated Input Current (A)
Rated Output for STICK (SMAW) Welding
Rated Output for LIFT TIG (GTAW) Welding
Duty Cycle (%)
Welder Type
Output Terminal Type
Classification
Protection Class
Standards
Cooling Method
Dimensions and Weight
Welding Power Source Mass
Welding Power Source Dimensions (Height x Width x Depth)
∆
The recommended time delay fuse or circuit breaker size is 30 amp. An individual branch circuit capable of carrying 30 amperes
and protected by fuses or circuit breaker is recommended for this application. Fuse size is based on not more than 200 percent
of the rated input amperage of the welding power source (Based on Article 630, National Electrical Code)
Thermal Arc continuously strives to produce the best product possible and therefore reserves the right to change, improve or revise the
specifications or design of this or any product without prior notice. Such updates or changes do not entitle the buyer of equipment previously
sold or shipped to the corresponding changes, updates, improvements or replacement of such items.
The values specified in the table above are optimal values, your values may differ. Individual equipment may differ from the above specifications
due to in part, but not exclusively, to any one or more of the following; variations or changes in manufactured components, installation location
and conditions and local power grid supply conditions.
Manual 0-5148
for STICK (SMAW) Welding
for LIFT TIG (GTAW) Welding
.
THERMAL ARC 161STL, 201TS
AC 115V
Single Phase
AC 104 - 127V
50/60 Hz
20 Amps
∆ 28.6 Amps
5 KVA
Stick: 10 - 125 Amps
TIG: 10 - 160 Amps
71V
100A @ 45%, 24.0V
95A @ 60%, 23.8V
80A @ 100%, 23.2V
28.6A
Io = 100A @ 24.0V
28.6A
Io = 150A @ 16.4V
24.0V, 100A @ 45%
16.0V, 150A @ 35%
45% @ 100A
Inverter Power Source
Heavy Duty Dinse
H 9.0" x W 5.3" x D 17.7"
(H230mm x W135mm x D450mm)
3-3
W1003700
AC 208/230V
Single Phase
AC 187- 253V
50/60 Hz
16 Amps
∆ 25 Amps
6 KVA
Stick:/TIG:
10 - 160 Amps
71V
160A @ 30%, 26.4V
120A @ 60%, 24.8V
100A @ 100%, 24.0V
25A
Io = 160A @ 26.4V
15.5A
Io = 160A @ 16.4V
26.4V, 160A @ 30%
16.4V, 160A @ 30%
30% @ 160A
50
TM
IP23S
EN 60974-1
EN50199
Fan Cooled
21.6 lb. (9.8 kg)
Safety and Installation