IEI Technology KINO-DQM871 User Manual
  1. Manuals
  2. Brands
  3. IEI Technology Manuals
  4. Motherboard
  5. KINO-DQM871
  6. User manual

IEI Technology KINO-DQM871 User Manual

Mini-itx sbc with 4th generation 22nm intel mobile cpu up to 16.0 gb ddr3, hdmi, lvds, displayport, vga dual gbe, sata 6gb/s, usb 3.0, dual pcie mini pcie x16, intel® amt 9.0, roh
Hide thumbs Also See for KINO-DQM871:
Table of Contents

Advertisement

Quick Links

Download this manual
KINO-DQM871 Mini-ITX SBC
MODEL:
KINO-DQM871
Mini-ITX SBC with 4th Generation 22nm Intel® Mobile CPU
Up to 16.0 GB DDR3, HDMI, LVDS, DisplayPort, VGA
Dual GbE, SATA 6Gb/s, USB 3.0, Dual PCIe Mini
PCIe x16, Intel® AMT 9.0, RoHS

User Manual

Page i
Rev. 1.00 – 30 August, 2013

Advertisement

Table of Contents
loading

Related Manuals for IEI Technology KINO-DQM871

Summary of Contents for IEI Technology KINO-DQM871

  • Page 1: User Manual

    KINO-DQM871 Mini-ITX SBC MODEL: KINO-DQM871 Mini-ITX SBC with 4th Generation 22nm Intel® Mobile CPU Up to 16.0 GB DDR3, HDMI, LVDS, DisplayPort, VGA Dual GbE, SATA 6Gb/s, USB 3.0, Dual PCIe Mini PCIe x16, Intel® AMT 9.0, RoHS User Manual Page i Rev.
  • Page 2 KINO-DQM871 Mini-ITX SBC Revision Date Version Changes 1.00 Initial release 30 August, 2013 Page ii...
  • Page 3 KINO-DQM871 Mini-ITX SBC Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.

  • Page 4: Table Of Contents

    KINO-DQM871 Mini-ITX SBC Table of Contents 1 INTRODUCTION......................1 1.1 I ......................2 NTRODUCTION 1.2 B ........................3 ENEFITS 1.3 F ........................3 EATURES 1.4 C ......................4 ONNECTORS 1.5 D ....................... 5 IMENSIONS 1.6 D ........................ 6 1.7 T ..................
  • Page 5 KINO-DQM871 Mini-ITX SBC 3.2.11 LVDS Connector..................... 27 3.2.12 LVDS Backlight Connector ................29 3.2.13 PCIe Mini Card Slot (Full-size)..............29 3.2.14 PCIe Mini Card Slot (Half-size) ..............31 3.2.15 PCI Express x16 Slot..................32 3.2.16 Power Button (On-board) ................35 3.2.17 Power Connector (12V) .................
  • Page 6 KINO-DQM871 Mini-ITX SBC 4.6.1 AT/ATX Mode Selection ................... 62 4.6.2 Clear CMOS..................... 63 4.6.3 LVDS Voltage Selection..................64 4.6.4 LVDS Resolution Selection ................65 4.7 C .................... 66 HASSIS NSTALLATION 4.7.1 Airflow......................66 4.7.2 Motherboard Installation................. 67 4.8 I ............67...
  • Page 7 5.3.10.1 Serial Port n Configuration ..............94 5.3.11 F81866 H/W Monitor ................... 100 5.3.11.1 Smart Fan Mode Configuration ............101 5.3.12 Serial Port Console Redirection ..............102 5.3.13 iEi Feature ....................105 5.4 C ......................... 106 HIPSET 5.4.1 System Agent (SA) Configuration ..............107 5.4.1.1 Graphics Configuration................
  • Page 8 KINO-DQM871 Mini-ITX SBC B.2 S ................ 148 ETUP ROCEDURE FOR INDOWS B.2.1 Hardware and BIOS Setup ................149 B.2.2 Create Partitions ................... 149 B.2.3 Install Operating System, Drivers and Applications ........153 B.2.4 Building the Recovery Partition ..............154 B.2.5 Create Factory Default Image............... 156 B.3 A...
  • Page 9 KINO-DQM871 Mini-ITX SBC List of Figures Figure 1-1: KINO-DQM871......................2 Figure 1-2: Connectors ........................4 Figure 1-3: KINO-DQM871 Dimensions (mm) ................5 Figure 1-4: Data Flow Diagram......................6 Figure 3-1: Connector and Jumper Locations................15 Figure 3-2: ATX Power Control Connector Location ..............18 Figure 3-3: Battery Connector Location..................19 Figure 3-4: Digital I/O Connector Location ................20...
  • Page 10 KINO-DQM871 Mini-ITX SBC Figure 3-27: EC SPI Flash Connector Location.................44 Figure 3-28: TPM Connector Location..................45 Figure 3-29: USB Connector Locations..................46 Figure 3-30: USB 3.0/2.0 Connector Location ................47 Figure 3-31: External Interface Connectors................48 Figure 3-32: Audio Jacks ......................49 Figure 3-33: Ethernet Connector....................49 Figure 3-34: Ethernet Connector....................51...
  • Page 11 Figure 6-30: Intel® ME Driver Setup Operations ..............139 Figure 6-31: Intel® ME Driver Installation Finish Screen ............140 Figure B-1: IEI One Key Recovery Tool Menu ................ 145 Figure B-2: Launching the Recovery Tool ................150 Figure B-3: Recovery Tool Setup Menu .................. 150 Figure B-4: Command Prompt ....................
  • Page 12 Figure B-27: Factory Default Image Confirmation ..............164 Figure B-28: Image Creation Complete ................... 165 Figure B-29: Press any key to continue .................. 165 Figure B-30: IEI Feature ......................166 Figure B-31: Partitions for Linux....................167 Figure B-32: Manual Recovery Environment for Linux ............168 Figure B-33: Access menu.lst in Linux (Text Mode) ..............
  • Page 13 KINO-DQM871 Mini-ITX SBC List of Tables Table 1-1: Technical Specifications....................8 Table 2-1: Packing List.........................12 Table 2-2: Optional Items......................13 Table 3-1: Peripheral Interface Connectors ................17 Table 3-2: Rear Panel Connectors ....................17 Table 3-3: ATX Power Control Connector Pinouts..............18 Table 3-4: Battery Connector Pinouts ..................20 Table 3-5: Digital I/O Connector Pinouts..................20...
  • Page 14 KINO-DQM871 Mini-ITX SBC Table 3-28: EC SPI Flash Connector Pinouts ................45 Table 3-29: TPM Connector Pinouts ...................46 Table 3-30: USB Port Connector Pinouts...................47 Table 3-31: USB 3.0/2.0 Connector Pinouts................48 Table 3-32: LAN Pinouts ......................49 Table 3-33: Connector LEDs......................50 Table 3-34: External USB 2.0 Port Pinouts ................50 Table 3-35: LAN Pinouts ......................50...
  • Page 15 BIOS Menu 15: F81866 H/W Monitor..................100 BIOS Menu 16: Smart Fan Mode Configuration ..............101 BIOS Menu 17: Serial Port Console Redirection ..............102 BIOS Menu 18: iEi Feature......................105 BIOS Menu 19: Chipset ......................106 BIOS Menu 20: System Agent (SA) Configuration ..............107 BIOS Menu 21: Graphics Configuration ..................

  • Page 16: Introduction

    KINO-DQM871 Mini-ITX SBC Chapter Introduction Page 1...

  • Page 17: Introduction

    KINO-DQM871 Mini-ITX SBC 1.1 Introduction Figure 1-1: KINO-DQM871 The KINO-DQM871 is a Mini-ITX SBC with a 4 generation 22nm Intel® mobile CPU and Intel® QM87 Express Chipset. Storage on the board is handled by two SATA 6Gb/s ports, two SATA 3Gb/s ports and one PCIe Mini socket for connecting a hard drive, optical drive or SSD.

  • Page 18: Benefits

    Some of the KINO-DQM871 motherboard benefits include: Low power consumption Wide range of I/O interfaces Triple independent display support 1.3 Features Some of the KINO-DQM871 motherboard features are listed below: Mini-ITX form factor RoHS compliant 4th generation 22mm Intel® Core™ mobile processor 1066/1333/1600MHz dual-channel DDR3 SDRAM Intel®...

  • Page 19: Connectors

    KINO-DQM871 Mini-ITX SBC 1.4 Connectors The connectors on the KINO-DQM871 are shown in the figure below. Figure 1-2: Connectors Page 4...

  • Page 20: Dimensions

    KINO-DQM871 Mini-ITX SBC 1.5 Dimensions The main dimensions of the KINO-DQM871 are shown in the diagram below. Figure 1-3: KINO-DQM871 Dimensions (mm) Page 5...

  • Page 21: Data Flow

    KINO-DQM871 Mini-ITX SBC 1.6 Data Flow Figure 1-4 shows the data flow between the system chipset, the CPU and other components installed on the motherboard. Figure 1-4: Data Flow Diagram Page 6...

  • Page 22: Technical Specifications

    KINO-DQM871 Mini-ITX SBC 1.7 Technical Specifications KINO-DQM871 technical specifications are listed in Table 1-1. Specification KINO-DQM871 Form Factor Mini-ITX generation 22nm Intel® mobile CPU System Chipset Intel® QM87 Memory Two 204-pin 1600/1333/1066 MHz DDR3 SO-DIMM supported (system max. 16.0 GB) Graphics Engine Supports DirectX 11.1, OpenGL 3.2, OpenCL 1.2, full MPEG2, VC1,...

  • Page 23: Table 1-1: Technical Specifications

    KINO-DQM871 Mini-ITX SBC One 4-pin wafer for CPU fan Fan connector One 4-pin wafer for system fan One internal 6-pin wafer connector Keyboard/Mouse Serial Ports Five RS-232 COM connectors (four by pin header, one on rear side) One RS-422/485 COM connector (4-pin wafer) Ten USB 2.0 ports (eight by 8-pin header, two on rear side )

  • Page 24: Packing List

    KINO-DQM871 Mini-ITX SBC Chapter Packing List Page 9...

  • Page 25: Anti-Static Precautions

    Only handle the edges of the PCB:- Don't touch the surface of the motherboard. Hold the motherboard by the edges when handling. 2.2 Unpacking Precautions When the KINO-DQM871 is unpacked, please do the following: Follow the antistatic guidelines above. Make sure the packing box is facing upwards when opening.

  • Page 26: Packing List

    NOTE: If any of the components listed in the checklist below are missing, do not proceed with the installation. Contact the IEI reseller or vendor the KINO-DQM871 was purchased from or contact an IEI sales representative directly by sending an email to sales@iei.com.tw.

  • Page 27: Optional Items

    KINO-DQM871 Mini-ITX SBC Quantity Item and Part Number Image Utility CD One Key Recovery CD Quick installation guide Table 2-1: Packing List 2.4 Optional Items These optional items are available. Item and Part Number Image RS-232/422/485 cable with bracket (P/N: 19800-0043000-100-RS)

  • Page 28: Table 2-2: Optional Items

    KINO-DQM871 Mini-ITX SBC Item and Part Number Image Infineon TPM module (P/N: TPM-IN01-R11) DisplayPort to 24-bit dual channel LVDS converter board (For IEI IDP connector) (P/N: DP-LVDS-R10) DisplayPort to HDMI converter board (For IEI IDP connector) (P/N: DP-HDMI-R10) DisplayPort to DVI-D converter board...

  • Page 29: Connector Pinouts

    KINO-DQM871 Mini-ITX SBC Chapter Connector Pinouts Page 14...

  • Page 30: Peripheral Interface Connectors

    KINO-DQM871 Mini-ITX SBC 3.1 Peripheral Interface Connectors Section 3.1.1 shows peripheral interface connector locations. Section 3.1.2 lists all the peripheral interface connectors seen in Section 3.1.1. 3.1.1 Layout The figure below shows the on-board peripheral connectors, rear panel peripheral connectors and on-board jumpers.

  • Page 31: Peripheral Interface Connectors

    KINO-DQM871 Mini-ITX SBC 3.1.2 Peripheral Interface Connectors The table below shows a list of the peripheral interface connectors on the KINO-DQM871. Detailed descriptions of these connectors can be found below. Connector Type Label ATX power signal connector 3-pin header PS_ON1...

  • Page 32: External Interface Panel Connectors

    USB 3.0/2.0 connector 20-pin box header Table 3-1: Peripheral Interface Connectors 3.1.3 External Interface Panel Connectors The table below lists the rear panel connectors on the KINO-DQM871. Detailed descriptions of these connectors can be found in a later section. Connector Type...

  • Page 33: Internal Peripheral Connectors

    Internal peripheral connectors are found on the motherboard and are only accessible when the motherboard is outside of the chassis. This section has complete descriptions of all the internal, peripheral connectors on the KINO-DQM871. 3.2.1 ATX Power Signal Connector CN Label:...

  • Page 34: Battery Connector

    KINO-DQM871 Mini-ITX SBC 3.2.2 Battery Connector CAUTION: Risk of explosion if battery is replaced by and incorrect type. Only certified engineers should replace the on-board battery. Dispose of used batteries according to instructions and local regulations. CN Label: BAT1 CN Type:...

  • Page 35: Digital I/O Connector

    KINO-DQM871 Mini-ITX SBC Description Battery+ Ground Table 3-4: Battery Connector Pinouts 3.2.3 Digital I/O Connector CN Label: DIO1 CN Type: 10-pin header CN Location: See Figure 3-4 CN Pinouts: See Table 3-5 The digital I/O connector provides programmable input and output for external devices.

  • Page 36: Displayport Connector

    KINO-DQM871 Mini-ITX SBC 3.2.4 DisplayPort Connector CN Label: 20-pin box header CN Type: CN Location: See Figure 3-5 CN Pinouts: See Table 3-6 Connects to a monitor that accepts DisplayPort input. Figure 3-5: DisplayPort Connector Location Description Description AUX_N2 DPB_OB_LANE1_N...

  • Page 37: Ec Debug Port

    KINO-DQM871 Mini-ITX SBC 3.2.5 EC Debug Port CN Label: LPT_DB1 20-pin header CN Type: CN Location: See Figure 3-6 CN Pinouts: See Table 3-7 The connector is for EC debug only. Figure 3-6: BIOS Debug Port Location Description Description KSI0...

  • Page 38: Fan Connector (Cpu)

    KINO-DQM871 Mini-ITX SBC 3.2.6 Fan Connector (CPU) CN Label: CPU_FAN1 4-pin wafer CN Type: CN Location: See Figure 3-7 CN Pinouts: See Table 3-8 The fan connector attaches to a CPU cooling fan. Figure 3-7: CPU Fan Connector Location Description...

  • Page 39: Front Panel Connector

    KINO-DQM871 Mini-ITX SBC CN Location: See Figure 3-8 CN Pinouts: See Table 3-9 The fan connector attaches to a system cooling fan. Figure 3-8: System Fan Connector Location Description +V12S Rotation Signal PWM Control Signal Table 3-9: System Fan Connector Pinouts 3.2.8 Front Panel Connector...

  • Page 40: Keyboard/Mouse Connector

    KINO-DQM871 Mini-ITX SBC The front panel connector connects to the indicator LEDs and buttons on the computer's front panel. Figure 3-9: Front Panel Connector Location Description Description Power PWR_LED+ Buzzer BEEP_PWR PWR_LED- Power PWRBTN_SW#_C PC_BEEP Button Reset HDD_LED+ EXTRST- HDD_LED- Table 3-10: Front Panel Connector Pinouts 3.2.9 Keyboard/Mouse Connector...

  • Page 41: Lan Active Led Connector

    KINO-DQM871 Mini-ITX SBC The keyboard/mouse connector connects to a PS/2 Y-cable that can be connected to a PS/2 keyboard and mouse. Figure 3-10: Keyboard/Mouse Connector Location Description VCC5_KBMS Mouse Data Mouse Clock Keyboard Data Keyboard Clock Table 3-11: Keyboard/Mouse Connector Pinouts 3.2.10 LAN Active LED Connector...

  • Page 42: Lvds Connector

    KINO-DQM871 Mini-ITX SBC Figure 3-11: LAN Active LED Connector Location Description Description LAN1_LINK_ACT- V_3P3_LAN LAN2_LINK_ACT- +3.3A Table 3-12: LAN Active LED Connector Pinouts 3.2.11 LVDS Connector CN Label: LVDS1 CN Type: 30-pin crimp CN Location: See Figure 3-12 CN Pinouts: See Table 3-13 The LVDS connector is for an LCD panel connected to the board.

  • Page 43: Figure 3-12: Lvds Connector Location

    KINO-DQM871 Mini-ITX SBC Figure 3-12: LVDS Connector Location Description Description A_Y0 A_Y0# A_Y1 A_Y1# A_Y2 A_Y2# A_CK A_CK# A_Y3 A_Y3# B_Y0 B_Y0# B_Y1 B_Y1# B_Y2 B_Y2# B_CK B_CK# B_Y3 B_Y3# VCC/VCC3 VCC/VCC3 VCC/VCC3 VCC/VCC3 Table 3-13: LVDS Connector Pinouts Page 28...

  • Page 44: Lvds Backlight Connector

    KINO-DQM871 Mini-ITX SBC 3.2.12 LVDS Backlight Connector CN Label: INV1 5-pin wafer CN Type: CN Location: See Figure 3-13 CN Pinouts: See Table 3-14 The backlight inverter connectors provide power to LCD panels. Figure 3-13: LVDS Backlight Inverter Connector Description...

  • Page 45: Figure 3-14: Pcie Mini Card Slot Location

    KINO-DQM871 Mini-ITX SBC CN Location: See Figure 3-14 CN Pinouts: See Table 3-15 The PCIe Mini card slot enables a PCIe Mini card expansion module to be connected to the board. Cards supported include among others PCIe Mini cards and mSATA cards.

  • Page 46: Pcie Mini Card Slot (Half-Size)

    KINO-DQM871 Mini-ITX SBC Description Description PETP2 (SATA_TX4+) USBD- USBD+ SATA_DET4_R_N 1.5V MSATA_SEL# VCC3 Table 3-15: PCIe Mini Card Slot Pinouts 3.2.14 PCIe Mini Card Slot (Half-size) CN Label: MINI_PCIE1 CN Type: Half-size PCIe Mini card slot See Figure 3-15 CN Location:...

  • Page 47: Pci Express X16 Slot

    KINO-DQM871 Mini-ITX SBC Description Description PCIE_WAKE# VCC3 1.5V CLK- CLK+ PCIRST# VCC3 PCIRST# PERN2 3VDual PERP2 1.5V SMBCLK PETN2 SMBDATA PETP2 USBD- USBD+ SATA_DET4_R_N 1.5V MSATA_SEL# VCC3 Table 3-16: PCIe Mini Card Slot Pinouts 3.2.15 PCI Express x16 Slot CN Label:...

  • Page 48: Figure 3-16: Pcie X16 Slot Location

    KINO-DQM871 Mini-ITX SBC CN Location: See Figure 3-16 CN Pinouts: See Table 3-17 (Side A) Table 3-18 (Side B) The PCIe x16 expansion cards slot is for PCIe x16 expansion cards. Figure 3-16: PCIe x16 Slot Location Description Description Description...

  • Page 49: Table 3-17: Pcie X16 Side A Pinouts

    KINO-DQM871 Mini-ITX SBC Description Description Description Description REFCLK- HSIn(4) HSIn(9) HSIp(0) HSIp(15) HSIn(0) HSIp(5) HSIp(10) HSIn(15) HSIn(5) HSIn(10) RSVD Table 3-17: PCIe x16 Side A Pinouts Description Description Description Description +12v +12v HSOp(2) RSVD HSOn(2) HSOp(7) HSOp(12) HSOn(7) HSOn(12) SMCLK...

  • Page 50: Power Button (On-Board)

    3.2.16 Power Button (On-board) CN Label: PWR_SW1 CN Type: Push button See Figure 3-17 CN Location: Push the on-board power button to power on the KINO-DQM871. Figure 3-17: On-board Power Button Location 3.2.17 Power Connector (12V) CN Label: PWR2 CN Type: 4-pin connector...

  • Page 51: Serial Port Connectors (Com2 ~ Com5)

    KINO-DQM871 Mini-ITX SBC Figure 3-18: Power Connector Location Description Description Ground Ground +12V +12V Table 3-19: Power Connector Pinouts 3.2.18 RS-232 Serial Port Connectors (COM2 ~ COM5) CN Label: COM2, COM3, COM4, COM5 CN Type: 10-pin header CN Location: See Figure 3-19...

  • Page 52: Rs-422/485 Serial Port Connector (Com6)

    KINO-DQM871 Mini-ITX SBC Figure 3-19: RS-232 Serial Port Connector Location Description Description -NDCD -NDSR NSIN -NRTS NSOUT -NCTS -NDTR -XRI Table 3-20: Serial Port Connector Pinouts 3.2.19 RS-422/485 Serial Port Connector (COM6) CN Label: COM6 CN Type: 4-pin wafer CN Location:...

  • Page 53: Sata 6Gb/S Drive Connectors

    KINO-DQM871 Mini-ITX SBC Figure 3-20: RS-422/485 Serial Port Connector Location Description RXD422- RXD422+ TXD422+/TXD485+ TXD422-/TXD485- Table 3-21: RS-422/485 Serial Port Connector Pinouts Use the optional RS-422/485 cable to connect to a serial device. The pinouts of the DB-9 connector are listed below.

  • Page 54: Sata 3Gb/S Drive Connectors

    KINO-DQM871 Mini-ITX SBC CN Pinouts: See Table 3-23 The SATA connectors connect to SATA hard drives or optical drives with data transfer speeds as high as 6Gb/s. Figure 3-21: SATA 6Gb/s Drive Connector Locations Description Table 3-23: SATA 6Gb/s Drive Connector Pinouts 3.2.21 SATA 3Gb/s Drive Connectors...

  • Page 55: Sata Power Connectors

    KINO-DQM871 Mini-ITX SBC The SATA connectors connect to SATA hard drives or optical drives with data transfer speeds as high as 3Gb/s. Figure 3-22: SATA 3Gb/s Drive Connector Locations Description Table 3-24: SATA 3Gb/s Drive Connector Pinouts 3.2.22 SATA Power Connectors...

  • Page 56: Smbus Connector

    KINO-DQM871 Mini-ITX SBC Figure 3-23: SATA Power Connector Locations Description +V12S +V5S Table 3-25: SATA Power Connector Pinouts 3.2.23 SMBus Connector CN Label: SMB1 CN Type: 4-pin wafer See Figure 3-24 CN Location: CN Pinouts: See Table 3-26 The SMBus (System Management Bus) connector provides low-speed system management communications.

  • Page 57: So-Dimm Connectors

    KINO-DQM871 Mini-ITX SBC Figure 3-24: SMBus Connector Location Description SMB_DATA SMB_CLK +V5S Table 3-26: SMBus Connector Pinouts 3.2.24 SO-DIMM Connectors CN Label: DIMM1, DIMM2 CN Type: 204-pin DDR3 SO-DIMM connector See Figure 3-25 CN Location: The SO-DIMM connector is for installing memory on the system.

  • Page 58: Spi Flash Connector

    KINO-DQM871 Mini-ITX SBC Figure 3-25: SO-DIMM Connector Locations 3.2.25 SPI Flash Connector CN Label: SPI1 6-pin wafer CN Type: CN Location: See Figure 3-26 CN Pinouts: See Table 3-27 The 6-pin SPI Flash connector is used to flash the BIOS.

  • Page 59: Spi Flash Connector (Ec)

    KINO-DQM871 Mini-ITX SBC Description +V3.3M_SPI_CON SPI_CS#0_CN SPI_SO_SW SPI_CLK_SW SPI_SI_SW Table 3-27: SPI Flash Connector Pinouts 3.2.26 SPI Flash Connector (EC) CN Label: JSPI1 CN Type: 6-pin wafer CN Location: See Figure 3-27 CN Pinouts: See Table 3-28 The 6-pin EC SPI Flash connector is used to flash the BIOS.

  • Page 60: Tpm Connector

    KINO-DQM871 Mini-ITX SBC Description +V3.3M_SPI_CON_EC SPI_CS#0_CN_EC SPI_SO_SW_EC SPI_CLK_SW_EC SPI_SI_SW_EC Table 3-28: EC SPI Flash Connector Pinouts 3.2.27 TPM Connector CN Label: TPM1 CN Type: 20-pin header CN Location: See Figure 3-28 CN Pinouts: See Table 3-29 The Trusted Platform Module (TPM) connector secures the system on bootup.

  • Page 61: Usb 2.0 Connectors

    KINO-DQM871 Mini-ITX SBC Description Description LRERST# LAD3 LAD2 LAD1 LAD0 SB3V SERIRQ GLKRUN# LPCPD# LDRQ# Table 3-29: TPM Connector Pinouts 3.2.28 USB 2.0 Connectors CN Label: USB1, USB2, USB3 8-pin header CN Type: CN Location: See Figure 3-29 CN Pinouts: See Table 3-30 The USB header can connect to two USB devices.

  • Page 62: Usb 3.0/2.0 Connector

    KINO-DQM871 Mini-ITX SBC Description Description DATA- DATA+ DATA+ DATA- Table 3-30: USB Port Connector Pinouts 3.2.29 USB 3.0/2.0 Connector CN Label: CN Type: 20-pin box header CN Location: See Figure 3-30 CN Pinouts: See Table 3-31 The connector supports two USB 3.0 ports and two USB 2.0 ports connection.

  • Page 63: External Interface Connectors

    USB3_RXDN4_C USB2_DP3 Table 3-31: USB 3.0/2.0 Connector Pinouts 3.3 External Interface Connectors Figure 3-31 shows the KINO-DQM871 motherboard external interface connectors. The KINO-DQM871 on-board external interface connectors are shown in Figure 3-31. Figure 3-31: External Interface Connectors 3.3.1 Audio Connector...

  • Page 64: Ethernet And Usb 2.0 Connectors

    KINO-DQM871 Mini-ITX SBC Figure 3-32: Audio Jacks 3.3.2 Ethernet and USB 2.0 Connectors CN Label: LAN2_USB2 CN Type: RJ-45 and USB 2.0 combo connector CN Location: See Figure 3-31 CN Pinouts: See Table 3-32 and Table 3-34 The LAN connector connects to a local network.

  • Page 65: Ethernet And Usb 3.0 Connectors

    KINO-DQM871 Mini-ITX SBC Description Description on: linked off: 10 Mb/s blinking: data is being sent/received green: 100 Mb/s orange: 1000 Mb/s Table 3-33: Connector LEDs The USB 2.0 connector can be connected to a USB device. Description VBUS Table 3-34: External USB 2.0 Port Pinouts 3.3.3 Ethernet and USB 3.0 Connectors...

  • Page 66: Hdmi Connectors

    KINO-DQM871 Mini-ITX SBC Figure 3-34: Ethernet Connector Description Description on: linked off: 10 Mb/s blinking: data is being sent/received green: 100 Mb/s orange: 1000 Mb/s Table 3-36: Connector LEDs The USB 3.0 connector can be connected to a USB device.

  • Page 67: Power Connector (12 V, Power Adapter)

    KINO-DQM871 Mini-ITX SBC Description Description HDMI_DATA2 HDMI_CLK# HDMI_DATA2# HDMI_DATA1 HDMI_SCL HDMI_DATA1# HDMI_SDA HDMI_DATA0 HDMI_DATA0# HDMI_HPD HDMI_CLK+ Table 3-38: HDMI Connector Pinouts Figure 3-35: HDMI Connector 3.3.5 Power Connector (12 V, Power Adapter) CN Label: PWR1 4-pin Mini-DIN CN Type: CN Location:...

  • Page 68: Serial Port Connector (Com1)

    KINO-DQM871 Mini-ITX SBC 3.3.6 Serial Port Connector (COM1) CN Label: COM1 DB-9 CN Type: CN Location: See Figure 3-31 CN Pinouts: See Table 3-39 The serial port connects to a RS-232 serial communications device. PIN NO. DESCRIPTION PIN NO. DESCRIPTION...

  • Page 69: Figure 3-38: Vga Connector

    KINO-DQM871 Mini-ITX SBC Figure 3-38: VGA Connector Description Description GREEN GROUND BLUE DDCDAT HSYNC VSYNC DDCCLK Table 3-40: VGA Connector Pinouts Page 54...

  • Page 70: Installation

    KINO-DQM871 Mini-ITX SBC Chapter Installation Page 55...

  • Page 71: Anti-Static Precautions

    Electrostatic discharge (ESD) can cause serious damage to electronic components, including the KINO-DQM871. Dry climates are especially susceptible to ESD. It is therefore critical to strictly adhere to the following anti-static precautions whenever the KINO-DQM871, or any other electrical component, is handled.
  • Page 72 KINO-DQM871 Mini-ITX SBC WARNING: The installation instructions described in this manual should be carefully followed in order to prevent damage to the KINO-DQM871, KINO-DQM871 components and injury to the user. Before and during the installation please DO the following: Read the user manual: The user manual provides a complete description of the installation instructions and configuration options.

  • Page 73: Cooling Kit Installation

    KINO-DQM871 Mini-ITX SBC 4.3 Cooling Kit Installation An IEI CPU cooling kit can be purchased separately (See Chapter 2). The cooling kit is comprised of a CPU heat sink and a cooling fan. WARNING: Do not wipe off (accidentally or otherwise) the pre-sprayed layer of thermal paste on the bottom of the heat sink.

  • Page 74: Figure 4-2: Align The Cooling Kit

    KINO-DQM871 Mini-ITX SBC Step 2: Properly orient the cooling kit. The CPU fan cable must not interfere with the fan or other moving parts. Make sure the cable can be routed away from the moving parts. Step 3: Properly align the cooling kit. Line up the four screws with the screw holes on the support bracket below the board (Figure 4-2).

  • Page 75: So-Dimm Installation

    KINO-DQM871 Mini-ITX SBC Figure 4-3: Secure the Cooling Kit 4.4 SO-DIMM Installation To install a SO-DIMM, please follow the steps below and refer to Figure 4-4. Figure 4-4: SO-DIMM Installation Page 60...

  • Page 76: Pcie Mini Card Installation

    The memory module is ejected by a mechanism in the socket.Step 0: 4.5 PCIe Mini Card Installation Two PCIe Mini card slots are located on the KINO-DQM871. To install the PCIe Mini card, please refer to the diagram and instructions below. Figure 4-5: PCIe Mini Card Installation Step 1: Insert into the socket at an angle.

  • Page 77: Jumper Settings

    OPEN a jumper means removing the plastic clip from a jumper. Before the KINO-DQM871 is installed in the system, the jumpers must be set in accordance with the desired configuration. The jumpers on the KINO-DQM871 are listed in Table 4-1.

  • Page 78: Clear Cmos

    KINO-DQM871 Mini-ITX SBC Set the switch to select AT or ATX power mode for the KINO-DQM871. AT power mode limits the system to on/off. ATX allows the system to use various power saving states and enter a standby state, so the system can be turned on remotely over a network. To configure, see the diagram below.

  • Page 79: Lvds Voltage Selection

    KINO-DQM871 Mini-ITX SBC Load Failsafe Defaults. After having done one of the above, save the changes and exit the CMOS Setup menu. Figure 4-7: Clear CMOS Jumper Location 4.6.3 LVDS Voltage Selection Jumper Label: JLCD_PWR1 Jumper Type: 6-pin header Jumper Settings:...

  • Page 80: Lvds Resolution Selection

    KINO-DQM871 Mini-ITX SBC Figure 4-8: LVDS Voltage Selection Jumper Location 4.6.4 LVDS Resolution Selection Jumper Label: Jumper Type: DIP switch Jumper Settings: See Table 4-3 Jumper Location: See Figure 4-9 Selects the resolution of the LCD panel connected to the LVDS connector.

  • Page 81: Chassis Installation

    The chassis should have fans and vents as necessary to keep things cool. The KINO-DQM871 must be installed in a chassis with ventilation holes on the sides allowing airflow to travel through the heat sink surface. In a system with an individual...

  • Page 82: Motherboard Installation

    This section outlines the installation of peripheral devices to the onboard connectors. 4.8.1 SATA Drive Connection The KINO-DQM871 is shipped with two SATA drive cable. To connect the SATA drive to the connector, please follow the steps below. Step 1: Locate the SATA connector and the SATA power connector.

  • Page 83: Single Rs-232 Cable (W/O Bracket)

    KINO-DQM871 Mini-ITX SBC Step 3: Connect the cable to the SATA disk. Connect the connector on the other end of the cable to the connector at the back of the SATA drive. See Figure 4-10. Step 4: To remove the SATA cable from the SATA connector, press the clip on the connector at the end of the cable.

  • Page 84: External Peripheral Interface Connection

    Devices can be connected to the external connectors. To install external devices, follow the directions in the subsections below. 4.9.1 Audio Connector The audio jacks on the external audio connector enable the KINO-DQM871 to be connected to a stereo sound setup. To install the audio devices, follow the steps below. Step 1: Identify the audio plugs.

  • Page 85: Hdmi Display Device Connection

    Step 0: 4.9.2 HDMI Display Device Connection The HDMI connector transmits a digital signal to compatible HDMI display devices such as a TV or computer screen. To connect the HDMI cable to the KINO-DQM871, follow the steps below. Step 1: Locate the HDMI connector.

  • Page 86: Lan Connection (Single Connector)

    Locate the RJ-45 connectors. The locations of the USB connectors are shown in Chapter 3. Step 2: Align the connectors. Align the RJ-45 connector on the LAN cable with one of the RJ-45 connectors on the KINO-DQM871. See Figure 4-14. Page 71...

  • Page 87: Serial Device Connection

    RJ-45 connector into the on-board RJ-45 connector. Step 0: 4.9.4 Serial Device Connection The KINO-DQM871 has a single female DB-9 connector on the external peripheral interface panel for a serial device. Follow the steps below to connect a serial device to the KINO-DQM871.

  • Page 88: Usb Connection (Dual Connector)

    4.9.5 USB Connection (Dual Connector) The external USB 2.0/3.0 connectors provide easier and quicker access to external USB devices. Follow the steps below to connect USB devices to the KINO-DQM871. Step 1: Locate the USB 2.0/3.0 connectors. The locations of the USB 2.0/3.0 connectors are shown in Chapter 3.

  • Page 89: Vga Monitor Connection

    Figure 4-16: USB Connector 4.9.6 VGA Monitor Connection The KINO-DQM871 has a single female DB-15 connector on the external peripheral interface panel. The DB-15 connector is connected to a CRT or VGA monitor. To connect a monitor to the KINO-DQM871, please follow the instructions below.

  • Page 90: Intel ® Amt Setup Procedure

    ® 4.10 Intel AMT Setup Procedure The KINO-DQM871 is featured with the Intel® Active Management Technology (AMT). To enable the Intel® AMT function, follow the steps below. Step 1: Make sure the DIMM1 socket is installed with one DDR3 SO-DIMM.
  • Page 91 KINO-DQM871 Mini-ITX SBC process. Enter the Intel® current ME password as it requires (the Intel® default password is admin). Step 0: NOTE: To change the password, enter a new password following the strong password rule (containing at least one upper case letter, one lower case letter, one digit and one special character, and be at least eight characters).

  • Page 92: Bios

    KINO-DQM871 Mini-ITX SBC Chapter BIOS Page 77...

  • Page 93: Introduction

    KINO-DQM871 Mini-ITX SBC 5.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. 5.1.1 Starting Setup The UEFI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways.

  • Page 94: Getting Help

    KINO-DQM871 Mini-ITX SBC Function Esc key Main Menu – Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu -- Exit current page and return to Main Menu General help, only for Status Page Setup Menu and Option...

  • Page 95: Main

    KINO-DQM871 Mini-ITX SBC 5.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.

  • Page 96: Advanced

    KINO-DQM871 Mini-ITX SBC System Overview The BIOS Information lists a brief summary of the BIOS. The fields in BIOS Information cannot be changed. The items shown in the system overview include: BIOS Information Processor Information Memory Information PCH Information SPI Clock Frequency...

  • Page 97: Acpi Settings

    KINO-DQM871 Mini-ITX SBC Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit > ACPI Settings System ACPI Parameters > RTC Wake Settings > Trusted Computing > CPU Configuration ---------------------- > SATA Configuration >...

  • Page 98: Rtc Wake Settings

    KINO-DQM871 Mini-ITX SBC ACPI Sleep State [S1 only (CPU Stop Clock)] Use the ACPI Sleep State option to specify the sleep state the system enters when it is not being used. S1 only (CPU Stop The system enters S1 (POS) sleep state. The...

  • Page 99: Trusted Computing

    KINO-DQM871 Mini-ITX SBC Wake system with Fixed Time [Disabled] Use the Wake system with Fixed Time option to enable or disable the system wake on alarm event. Disabled The real time clock (RTC) cannot generate a wake EFAULT event Enabled...

  • Page 100: Bios Menu 5: Trusted Computing

    KINO-DQM871 Mini-ITX SBC Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced Configuration Enables or Disables BIOS Security Device Support [Disable] support for security device. O.S. will not Current Status Information show Security Device. NO Security Device Found...

  • Page 101: Cpu Configuration

    KINO-DQM871 Mini-ITX SBC 5.3.4 CPU Configuration Use the CPU Configuration menu (BIOS Menu 6) to view detailed CPU specifications and configure the CPU. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced CPU Configuration Enabled for Windows XP and Linux (OS optimized Intel(R) Core(TM) i5-4402E CPU @ 1.60GHz...
  • Page 102 KINO-DQM871 Mini-ITX SBC Intel VT-x Technology: Indicates if Intel VT-x Technology is supported by the CPU. Intel SMX Technology: Indicates if Intel SMX Technology is supported by the CPU. EIST Technology: Indicates if the Enhanced Intel SpeedStep® Technology (EIST) is supported by the CPU.

  • Page 103: Sata Configuration

    KINO-DQM871 Mini-ITX SBC 5.3.5 SATA Configuration Use the SATA Configuration menu (BIOS Menu 7) to change and/or set the configuration of the SATA devices installed in the system. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced SATA Controller(s)

  • Page 104: Intel(R) Rapid Start Technology

    KINO-DQM871 Mini-ITX SBC NOTE: Before accessing the RAID configuration utility, ensure to set the Option ROM Messages BIOS option in the Boot menu to Force BIOS. This is to allow the “Press <CTRL+I> to enter Configuration Utility……” message to appear during POST. Press Ctrl+I when prompted to enter the RAID configuration utility.

  • Page 105: Amt Configuration

    KINO-DQM871 Mini-ITX SBC 5.3.7 AMT Configuration The AMT Configuration menu (BIOS Menu 9) allows the advanced power management options to be configured. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced Intel AMT [Enabled] Enable/Disable Intel (R) Un-Configure ME...

  • Page 106: Usb Configuration

    KINO-DQM871 Mini-ITX SBC 5.3.8 USB Configuration Use the USB Configuration menu (BIOS Menu 10) to read USB configuration information and configure the USB settings. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced USB Configuration Enables Legacy USB support.

  • Page 107: Iwdd H/W Monitor

    KINO-DQM871 Mini-ITX SBC Enabled Legacy USB support enabled EFAULT Legacy USB support disabled Disabled Auto Legacy USB support disabled if no USB devices are connected 5.3.9 iWDD H/W Monitor The iWDD H/W Monitor menu (BIOS Menu 11) displays the CPU temperature and CPU fan speed, and contains the fan configuration submenu.

  • Page 108: Bios Menu 12: Smar Fan Mode Configuration

    KINO-DQM871 Mini-ITX SBC Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced Smart Fan Mode Configuration Smart Fan Mode Select Fan 1 Smart Fan Control [Auto Mode] Auto mode fan start temperature 50 Auto mode fan off temperature...

  • Page 109: F81866 Super Io Configuration

    KINO-DQM871 Mini-ITX SBC 5.3.10 F81866 Super IO Configuration Use the F81866 Super IO Configuration menu (BIOS Menu 13) to set or change the configurations for the serial ports. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced F81866 Super IO Configuration...
  • Page 110 KINO-DQM871 Mini-ITX SBC 5.3.10.1.1 Serial Port 1 Configuration Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port. Disabled Disable the serial port Enable the serial port Enabled EFAULT Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address.
  • Page 111 KINO-DQM871 Mini-ITX SBC Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address. Auto The serial port IO port address and interrupt address EFAULT are automatically detected. Serial Port I/O port address is 2F8h and the interrupt IO=2F8h;...
  • Page 112 KINO-DQM871 Mini-ITX SBC IO=3E8h; Serial Port I/O port address is 3E8h and the interrupt IRQ=10 address is IRQ10 Serial Port I/O port address is 3E8h and the interrupt IO=3E8h; address is IRQ10, 11 IRQ=10, 11 IO=2E8h; Serial Port I/O port address is 2E8h and the interrupt...
  • Page 113 KINO-DQM871 Mini-ITX SBC IO=2D0h; Serial Port I/O port address is 2D0h and the interrupt IRQ=10, 11 address is IRQ10, 11 Serial Port I/O port address is 2D8h and the interrupt IO=2D8h; address is IRQ10, 11 IRQ=10, 11 5.3.10.1.5 Serial Port 5 Configuration Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port.
  • Page 114 KINO-DQM871 Mini-ITX SBC 5.3.10.1.6 Serial Port 6 Configuration Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port. Disabled Disable the serial port Enable the serial port Enabled EFAULT Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address.

  • Page 115: F81866 H/W Monitor

    KINO-DQM871 Mini-ITX SBC 5.3.11 F81866 H/W Monitor The F81866 H/W Monitor menu (BIOS Menu 15) contains the fan configuration submenu and displays the system fan speeds. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced PC Health Status Smart Fan Mode Select >...

  • Page 116: Smart Fan Mode Configuration

    KINO-DQM871 Mini-ITX SBC 5.3.11.1 Smart Fan Mode Configuration Use the Smart Fan Mode Configuration submenu (BIOS Menu 16) to configure fan temperature and speed settings. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced Smart Fan Mode Configuration...

  • Page 117: Serial Port Console Redirection

    KINO-DQM871 Mini-ITX SBC 5.3.12 Serial Port Console Redirection The Serial Port Console Redirection menu (BIOS Menu 17) allows the console redirection options to be configured. Console redirection allows users to maintain a system remotely by re-directing keyboard input and text output through the serial port.
  • Page 118 KINO-DQM871 Mini-ITX SBC NOTE: The following five options appear when the Console Redirection option is enabled. Terminal Type [ANSI] Use the Terminal Type option to specify the remote terminal type. VT100 The target terminal type is VT100 The target terminal type is VT100+...
  • Page 119 KINO-DQM871 Mini-ITX SBC Sets the data bits at 8. EFAULT Parity [None] Use the Parity option to specify the parity bit that can be sent with the data bits for detecting the transmission errors. No parity bit is sent with the data bits.

  • Page 120: Iei Feature

    KINO-DQM871 Mini-ITX SBC 5.3.13 iEi Feature Use the iEi Feature menu (BIOS Menu 18) to configure One Key Recovery function. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced iEi Feature Auto Recovery Function Reboot and recover Auto Recovery Function...

  • Page 121: Chipset

    KINO-DQM871 Mini-ITX SBC 5.4 Chipset Use the Chipset menu (BIOS Menu 19) to access the PCH IO and System Agent (SA) configuration menus. WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction.

  • Page 122: System Agent (Sa) Configuration

    KINO-DQM871 Mini-ITX SBC 5.4.1 System Agent (SA) Configuration Use the System Agent (SA) Configuration menu (BIOS Menu 20) to configure the System Agent (SA) parameters. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Chipset VT-d Capability Supported Check to enable VT-d...

  • Page 123: Bios Menu 21: Graphics Configuration

    KINO-DQM871 Mini-ITX SBC Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Chipset Graphics Configuration Select which of IGFX/PEG/PCI Graphics Primary Display [Auto] device should be Primary DVMT Pre-Allocated [256M] Display Or select SG for DVMT Total Gfx Mem [MAX] Switchable Gfx.
  • Page 124 KINO-DQM871 Mini-ITX SBC DVMT Total Gfx Mem [MAX] Use the DVMT Total Gfx Mem option to select DVMT5.0 total graphic memory size used by the internal graphic device. The following options are available: 128M 256M Default Primary IGFX Boot Display [VBIOS Default] Use the Primary IGFX Boot Display option to select the display device used by the system when it boots.

  • Page 125: Nb Pcie Configuration

    KINO-DQM871 Mini-ITX SBC 5.4.1.2 NB PCIe Configuration Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Chipset NB PCIe Configuration Configure PEG0 B0:D1:F0 PCIEX16 Not Present Gen1-Gen3 PCIEX16 – Gen X [Auto] Enable PEG [Auto] Detect Non-Compliance Device [Disabled]...

  • Page 126: Memory Configuration

    KINO-DQM871 Mini-ITX SBC Disabled Default Enabled 5.4.1.3 Memory Configuration Use the Memory Configuration submenu (BIOS Menu 23) to view memory information. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Chipset Memory Information Memory Frequency 1333 Mhz Total Memory...

  • Page 127: Pch-Io Configuration

    KINO-DQM871 Mini-ITX SBC 5.4.2 PCH-IO Configuration Use the PCH-IO Configuration menu (BIOS Menu 24) to configure the PCH parameters. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Chipset Restore AC Power Loss [Last State] Select AC power state...

  • Page 128: Pci Express Configuration

    KINO-DQM871 Mini-ITX SBC Disabled The onboard High Definition Audio controller is disabled onboard High Definition Audio controller Enabled EFAULT automatically detected and enabled Power Saving Function [Disabled] Use the Power Saving Function option to enable or disable power saving function.

  • Page 129: Boot

    KINO-DQM871 Mini-ITX SBC Gen2 Detect Non-Compliance Device [Disabled] Use the Detect Non-Compliance Device option to enable or disable the “detect no-compliance PCIe device” function. Disabled Detect no-compliance PCIe device function is disabled EFAULT Detect no-compliance PCIe device function is enabled. If Enabled will take more time at POST if it is enabled.
  • Page 130 KINO-DQM871 Mini-ITX SBC Allows the Number Lock on the keyboard to be EFAULT enabled automatically when the computer system boots up. This allows the immediate use of the 10-key numeric keypad located on the right side of the keyboard. To confirm this, the Number Lock LED light on the keyboard is lit.

  • Page 131: Security

    KINO-DQM871 Mini-ITX SBC Enabled Load PXE Option ROMs. UEFI Boot [Disabled] Use the UEFI Boot BIOS option to allow the system to boot from the UEFI devices. Disabled Disables to boot from the UEFI devices. EFAULT Enabled Enables to boot from the UEFI devices.

  • Page 132: Save & Exit

    KINO-DQM871 Mini-ITX SBC 5.7 Save & Exit Use the Save & Exit menu (BIOS Menu 28) to load default BIOS values, optimal failsafe values and to save configuration changes. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main...
  • Page 133 KINO-DQM871 Mini-ITX SBC Restore User Defaults Use the Restore User Defaults option to restore the user defaults to all the setup options. Page 118...

  • Page 134: Software Drivers

    KINO-DQM871 Mini-ITX SBC Chapter Software Drivers Page 119...

  • Page 135: Available Software Drivers

    NOTE: The content of the CD may vary throughout the life cycle of the product and is subject to change without prior notice. Visit the IEI website or contact technical support for the latest updates. The following drivers can be installed on the system:...

  • Page 136: Figure 6-1: Start Up Screen

    KINO-DQM871 Mini-ITX SBC Figure 6-1: Start Up Screen Step 3: Click KINO-DQM871. Step 4: The list of drivers in Figure 6-2 appears. Figure 6-2: Drivers Page 121...

  • Page 137: Chipset Driver Installation

    KINO-DQM871 Mini-ITX SBC 6.3 Chipset Driver Installation To install the chipset driver, please do the following. Step 1: Access the driver list. (See Section 6.2) Step 2: Click “1-Chipset”. Step 3: Locate the setup file and double click on it.

  • Page 138: Figure 6-4: Chipset Driver License Agreement

    KINO-DQM871 Mini-ITX SBC Figure 6-4: Chipset Driver License Agreement Step 8: The Read Me file in Figure 6-5 appears. Step 9: Click Next to continue. Figure 6-5: Chipset Driver Read Me File Page 123...

  • Page 139: Figure 6-6: Chipset Driver Setup Operations

    KINO-DQM871 Mini-ITX SBC Step 10: Setup Operations are performed as shown in Figure 6-6. Figure 6-6: Chipset Driver Setup Operations Step 11: Once the Setup Operations are complete, click Next to continue. Step 12: The Finish screen in Figure 6-7 appears.

  • Page 140: Graphics Driver Installation

    KINO-DQM871 Mini-ITX SBC Figure 6-7: Chipset Driver Installation Finish Screen 6.4 Graphics Driver Installation To install the graphics driver, please do the following. Step 1: Access the driver list. (See Section 6.2) Step 2: Click “2-Graphics” and select the folder which corresponds to the operating system.

  • Page 141: Figure 6-8: Graphics Driver Welcome Screen

    KINO-DQM871 Mini-ITX SBC Figure 6-8: Graphics Driver Welcome Screen Step 5: The license agreement in Figure 6-9 appears. Read the License Agreement. Step 6: Click Yes to continue. Figure 6-9: Graphics Driver License Agreement Page 126...

  • Page 142: Figure 6-10: Graphics Driver Read Me File

    KINO-DQM871 Mini-ITX SBC Step 7: The Read Me file in Figure 6-10 appears. Step 8: Click Next to continue. Figure 6-10: Graphics Driver Read Me File Step 9: Setup Operations are performed as shown in Figure 6-11. Figure 6-11: Graphics Driver Setup Operations...

  • Page 143: Lan Driver Installation

    KINO-DQM871 Mini-ITX SBC Step 10: Once the Setup Operations are complete, click the Next icon to continue. Step 11: The Finish screen appears. Step 12: Select “Yes, I want to restart the computer now” and click the Finish icon. See Figure 6-12.

  • Page 144: Figure 6-13: Windows Control Panel

    KINO-DQM871 Mini-ITX SBC Figure 6-13: Windows Control Panel Step 2: The system control panel window in Figure 6-14 appears. Step 3: Click the Device Manager link (Figure 6-14). Figure 6-14: System Control Panel Step 4: A list of system hardware devices appears (Figure 6-15).

  • Page 145: Figure 6-15: Device Manager List

    KINO-DQM871 Mini-ITX SBC Step 6: Select Update Driver Software. Figure 6-15: Device Manager List Step 7: The Update Driver Software Window appears (Figure 6-16). Page 130...

  • Page 146: Figure 6-16: Update Driver Software Window

    KINO-DQM871 Mini-ITX SBC Figure 6-16: Update Driver Software Window Step 8: Select “Browse my computer for driver software” and click N to continue. Step 9: Click Browse to select “X:\3-LAN” directory in the Locate File window, where “X:\” is the system CD drive. (Figure 6-17).

  • Page 147: Figure 6-18: Lan Driver Installation

    KINO-DQM871 Mini-ITX SBC Step 11: Driver Installation is performed as shown in Figure 6-18. Figure 6-18: LAN Driver Installation Step 12: The Finish screen in Figure 6-19 appears. Click Close to exit. Figure 6-19: LAN Driver Installation Complete Page 132...

  • Page 148: Usb 3.0 Driver Installation

    KINO-DQM871 Mini-ITX SBC 6.6 USB 3.0 Driver Installation WARNING: Do not run this driver’s installer (Setup.exe) from a USB storage device (ie. external USB hard drive or USB thumb drive). For proper installation, please copy driver files to a local hard drive folder and run from there.

  • Page 149: Figure 6-21: Usb 3.0 Driver License Agreement

    KINO-DQM871 Mini-ITX SBC Step 6: The license agreement in Figure 6-21 appears. Step 7: Read the License Agreement. Step 8: Click Yes to continue. Figure 6-21: USB 3.0 Driver License Agreement Step 9: The Read Me file in Figure 6-22 appears.

  • Page 150: Figure 6-23: Usb 3.0 Driver Setup Operations

    KINO-DQM871 Mini-ITX SBC Step 11: Setup Operations are performed as shown in Figure 6-23. Step 12: Once the Setup Operations are complete, click Next to continue. Figure 6-23: USB 3.0 Driver Setup Operations Step 13: The Finish screen in Figure 6-24 appears.

  • Page 151: Audio Driver Installation

    KINO-DQM871 Mini-ITX SBC 6.7 Audio Driver Installation To install the Audio driver, please do the following. Step 1: Access the driver list. (See Section 6.2) Step 2: Click “5-Audio” and select the folder which corresponds to the operating system. Step 3: Double click the setup file.

  • Page 152: Figure 6-26: Audio Driver Installation

    KINO-DQM871 Mini-ITX SBC Figure 6-26: Audio Driver Installation Step 8: When the driver installation is complete, the screen in Figure 6-27 appears. Figure 6-27: Audio Driver Installation Complete Step 9: Select “Yes, I want to restart my computer now” and click Finish.

  • Page 153: Intel® Amt Driver Installation

    KINO-DQM871 Mini-ITX SBC 6.8 Intel® AMT Driver Installation To install these Intel® AMT components, please do the following. Step 1: Access the driver list. (See Section 6.2) Step 2: Click “7-iAMT Driver & Utility”. Step 3: Locate the setup file and double click it.

  • Page 154: Figure 6-29: Intel® Me Driver License Agreement

    KINO-DQM871 Mini-ITX SBC Figure 6-29: Intel® ME Driver License Agreement Step 9: Setup Operations are performed as shown in Figure 6-30. Step 10: Once the Setup Operations are complete, click Next to continue. Figure 6-30: Intel® ME Driver Setup Operations Step 11: The Finish screen in Figure 6-31 appears.

  • Page 155: Figure 6-31: Intel® Me Driver Installation Finish Screen

    KINO-DQM871 Mini-ITX SBC Step 12: Select “Yes, I want to restart this computer now” and click Finish.Step 0: Figure 6-31: Intel® ME Driver Installation Finish Screen Page 140...

  • Page 156: Abios Options

    KINO-DQM871 Mini-ITX SBC Appendix BIOS Options Page 141...
  • Page 157 KINO-DQM871 Mini-ITX SBC Below is a list of BIOS configuration options in the BIOS chapter. 　 System Overview .........................81 　 System Date [xx/xx/xx] ......................81 　 System Time [xx:xx:xx] .......................81 　 ACPI Sleep State [S1 only (CPU Stop Clock)]..............83 　 Wake system with Fixed Time [Disabled]................84 　...
  • Page 158 KINO-DQM871 Mini-ITX SBC 　 CPU_FAN1/SYS_FAN1 Smart Fan Mode [Auto Duty-Cycle Mode] ......101 　 CPU/System Temperature n..................... 101 　 Console Redirection [Disabled] ..................102 　 Terminal Type [ANSI]......................103 　 Bits per second [115200]....................103 　 Data Bits [8] ........................103 　...

  • Page 159: B One Key Recovery

    KINO-DQM871 Mini-ITX SBC Appendix One Key Recovery Page 144...

  • Page 160: One Key Recovery Introduction

    The IEI One Key Recovery tool menu is shown below. Figure B-1: IEI One Key Recovery Tool Menu Prior to using the IEI One Key Recovery tool (as shown in Figure B-1) to backup or restore Windows system, five setup procedures are required.

  • Page 161: System Requirement

    Section B.3. B.1.1 System Requirement NOTE: The recovery CD can only be used with IEI products. The software will fail to run and a warning message will appear when used on non-IEI hardware. To create the system backup, the main storage device must be split into two partitions (three partitions for Linux).

  • Page 162: Supported Operating System

    KINO-DQM871 Mini-ITX SBC partitions. Please take the following table as a reference when calculating the size of the partition. OS Image after Ghost Compression Ratio Windows® 7 7 GB 5 GB Windows® XPE 776 MB 560 MB Windows® CE 6.0...

  • Page 163: Setup Procedure For Windows

    KINO-DQM871 Mini-ITX SBC Linux Fedora Core 12 (Constantine) Fedora Core 11 (Leonidas) Fedora Core 10 (Cambridge) Fedora Core 8 (Werewolf) Fedora Core 7 (Moonshine) RedHat RHEL-5.4 RedHat 9 (Ghirke) Ubuntu 8.10 (Intrepid) Ubuntu 7.10 (Gutsy) Ubuntu 6.10 (Edgy) Debian 5.0 (Lenny) Debian 4.0 (Etch)

  • Page 164: Hardware And Bios Setup

    KINO-DQM871 Mini-ITX SBC The detailed descriptions are described in the following sections. NOTE: The setup procedures described below are for Microsoft Windows operating system users. For Linux, most of the setup procedures are the same except for several steps described in Section B.3.

  • Page 165: Figure B-2: Launching The Recovery Tool

    KINO-DQM871 Mini-ITX SBC Step 2: Boot the system from recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure B-2: Launching the Recovery Tool Step 3: The recovery tool setup menu is shown as below.

  • Page 166: Figure B-4: Command Prompt

    KINO-DQM871 Mini-ITX SBC Figure B-4: Command Prompt Step 5: The command prompt window appears. Type the following commands (marked in red) to create two partitions. One is for the OS installation; the other is for saving recovery files and images which will be an invisible partition.

  • Page 167: Figure B-5: Partition Creation Commands

    KINO-DQM871 Mini-ITX SBC Figure B-5: Partition Creation Commands Page 152...

  • Page 168: Install Operating System, Drivers And Applications

    KINO-DQM871 Mini-ITX SBC NOTE: Use the following commands to check if the partitions were created successfully. Step 6: Press any key to exit the recovery tool and automatically reboot the system. Please continue to the following procedure: Build the Recovery Partition.S t e p 0 :...

  • Page 169: Building The Recovery Partition

    KINO-DQM871 Mini-ITX SBC B.2.4 Building the Recovery Partition Step 1: Put the recover CD in the optical drive. Step 2: Start the system. Step 3: Boot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please...

  • Page 170: Figure B-8: Building The Recovery Partition

    KINO-DQM871 Mini-ITX SBC Step 5: The Symantec Ghost window appears and starts configuring the system to build a recovery partition. In this process the partition created for recovery files in Section B.2.2 is hidden and the recovery tool is saved in this partition.

  • Page 171: Create Factory Default Image

    KINO-DQM871 Mini-ITX SBC B.2.5 Create Factory Default Image NOTE: Before creating the factory default image, please configure the system to a factory default environment, including driver and application installations. To create a factory default image, please follow the steps below.

  • Page 172: Figure B-12: About Symantec Ghost Window

    KINO-DQM871 Mini-ITX SBC Figure B-12: About Symantec Ghost Window Step 4: Use mouse to navigate to the option shown below (Figure B-13). Figure B-13: Symantec Ghost Path Step 5: Select the local source drive (Drive 1) as shown in Figure B-14. Then click OK.

  • Page 173: Figure B-14: Select A Local Source Drive

    Select 1.2: [Recovery] NTFS drive and enter a file name called (Figure B-16). Click Save. The factory default image will then be saved in the selected recovery drive and named IEI.GHO. WARNING: The file name of the factory default image must be iei.GHO. Page 158...

  • Page 174: Figure B-16: File Name To Copy Image To

    KINO-DQM871 Mini-ITX SBC Figure B-16: File Name to Copy Image to Step 8: When the Compress Image screen in Figure B-17 prompts, click High to make the image file smaller. Figure B-17: Compress Image Page 159...

  • Page 175: Figure B-18: Image Creation Confirmation

    KINO-DQM871 Mini-ITX SBC Step 9: The Proceed with partition image creation window appears, click Yes to continue. Figure B-18: Image Creation Confirmation Step 10: The Symantec Ghost starts to create the factory default image (Figure B-19). Figure B-19: Image Creation Complete Step 11: When the image creation completes, a screen prompts as shown in Figure B-20.

  • Page 176: Auto Recovery Setup Procedure

    KINO-DQM871 Mini-ITX SBC Step 12: The recovery tool main menu window is shown as below. Press any key to reboot the system. S t e p 0 : Figure B-21: Press Any Key to Continue B.3 Auto Recovery Setup Procedure...

  • Page 177: Figure B-22: Auto Recovery Utility

    KINO-DQM871 Mini-ITX SBC Step 1: Follow the steps described in Section B.2.1 ~ Section B.2.3 to setup BIOS, create partitions and install operating system. Step 2: Install the auto recovery utility into the system by double clicking the Utility/AUTORECOVERY-SETUP.exe in the One Key Recovery CD. This utility MUST be installed in the system, otherwise, the system will automatically restore from the factory default image every ten (10) minutes.

  • Page 178: Figure B-24: Launching The Recovery Tool

    KINO-DQM871 Mini-ITX SBC Step 4: Reboot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure B-24: Launching the Recovery Tool Step 5: When the recovery tool setup menu appears, press <4>...

  • Page 179: Figure B-26: Building The Auto Recovery Partition

    KINO-DQM871 Mini-ITX SBC Figure B-26: Building the Auto Recovery Partition Step 7: After completing the system configuration, the following message prompts to confirm whether to create a factory default image. Type Y to have the system create a factory default image automatically. Type N within 6 seconds to skip this process (The default option is YES).

  • Page 180: Figure B-28: Image Creation Complete

    KINO-DQM871 Mini-ITX SBC Step 8: The Symantec Ghost starts to create the factory default image (Figure B-28). Figure B-28: Image Creation Complete Step 9: After completing the system configuration, press any key in the following window to restart the system.

  • Page 181: Setup Procedure For Linux

    KINO-DQM871 Mini-ITX SBC BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit iEi Feature ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Auto Recovery Function [Enabled] Recover from PXE [Disabled] Select Screen ↑ ↓ Select Item Enter Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc.

  • Page 182: Figure B-31: Partitions For Linux

    KINO-DQM871 Mini-ITX SBC Partition 1: / Partition 2: SWAP NOTE: Please reserve enough space for partition 3 for saving recovery images. Figure B-31: Partitions for Linux Step 3: Create a recovery partition. Insert the recovery CD into the optical disk drive.

  • Page 183: Figure B-32: Manual Recovery Environment For Linux

    KINO-DQM871 Mini-ITX SBC recovery partition. After completing the system configuration, press any key to reboot the system. Eject the recovery CD. Figure B-32: Manual Recovery Environment for Linux Step 5: Access the recovery tool main menu by modifying the “menu.lst”. To first access the recovery tool main menu, the menu.lst must be modified.

  • Page 184: Recovery Tool Functions

    KINO-DQM871 Mini-ITX SBC Step 7: The recovery tool menu appears. (Figure B-34) Figure B-34: Recovery Tool Menu Step 8: Create a factory default image. Follow Step 2 Step 12 described in Section B.2.5 to create a factory default image. S t e p 0 : B.5 Recovery Tool Functions...

  • Page 185: Figure B-35: Recovery Tool Main Menu

    KINO-DQM871 Mini-ITX SBC Figure B-35: Recovery Tool Main Menu The recovery tool has several functions including: 1. Factory Restore: Restore the factory default image (iei.GHO) created in Section B.2.5. 2. Backup system: Create a system backup image (iei_user.GHO) which will be saved in the hidden partition.

  • Page 186: Factory Restore

    Type <1> and press <Enter> in the main menu. Step 2: The Symantec Ghost window appears and starts to restore the factory default. A factory default image called iei.GHO is created in the hidden Recovery partition. Figure B-36: Restore Factory Default Step 3: The screen shown in Figure B-37 appears when completed.

  • Page 187: Backup System

    KINO-DQM871 Mini-ITX SBC B.5.2 Backup System To backup the system, please follow the steps below. Step 1: Type <2> and press <Enter> in the main menu. Step 2: The Symantec Ghost window appears and starts to backup the system. A backup image called iei_user.GHO is created in the hidden Recovery partition.

  • Page 188: Restore Your Last Backup

    KINO-DQM871 Mini-ITX SBC B.5.3 Restore Your Last Backup To restore the last system backup, please follow the steps below. Step 1: Type <3> and press <Enter> in the main menu. Step 2: The Symantec Ghost window appears and starts to restore the last backup image (iei_user.GHO).

  • Page 189: Manual

    KINO-DQM871 Mini-ITX SBC B.5.4 Manual To restore the last system backup, please follow the steps below. Step 1: Type <4> and press <Enter> in the main menu. Step 2: The Symantec Ghost window appears. Use the Ghost program to backup or recover the system manually.

  • Page 190: Restore Systems From A Linux Server Through Lan

    KINO-DQM871 Mini-ITX SBC B.6 Restore Systems from a Linux Server through LAN The One Key Recovery allows a client system to automatically restore to a factory default image saved in a Linux system (the server) through LAN connectivity after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes.

  • Page 191: Configure Dhcp Server Settings

    KINO-DQM871 Mini-ITX SBC B.6.1 Configure DHCP Server Settings Step 1: Install the DHCP #yum install dhcp (CentOS, commands marked in red) #apt-get install dhcp3-server (Debian, commands marked in blue) Step 2: Confirm the operating system default settings: dhcpd.conf. CentOS Use the following command to show the DHCP server sample location: #vi /etc/dhcpd.conf...

  • Page 192: Configure Tftp Settings

    KINO-DQM871 Mini-ITX SBC filename “pxelinux.0”; B.6.2 Configure TFTP Settings Step 1: Install the tftp, httpd and syslinux. #yum install tftp-server httpd syslinux (CentOS) #apt-get install tftpd-hpa xinetd syslinux (Debian) Step 2: Enable the TFTP server by editing the “/etc/xinetd.d/tftp” file and make it use the remap file.

  • Page 193: Configure One Key Recovery Server Settings

    KINO-DQM871 Mini-ITX SBC Debian Replace the TFTP settings from “inetd” to “xinetd” and annotate the “inetd” by adding “#”. #vi /etc/inetd.conf Modify: #tftp dgram udp wait root /usr/sbin..(as shown below) #vi /etc/xinetd.d/tftp B.6.3 Configure One Key Recovery Server Settings Step 1: Copy the Utility/RECOVERYR10.TAR.BZ2 package from the One Key...

  • Page 194: Start The Dhcp, Tftp And Http

    Create a shared directory for the factory default image. #mkdir /share #cd /share #mkdir /image #cp iei.gho /image WARNING: The file name of the factory default image must be iei.gho. Step 3: Confirm the operating system default settings: smb.conf. #vi /etc/samba/smb.conf Page 179...

  • Page 195: Setup A Client System For Auto Recovery

    KINO-DQM871 Mini-ITX SBC Modify: [image] comment = One Key Recovery path = /share/image browseable = yes writable = yes public = yes create mask = 0644 directory mask = 0755 Step 4: Edit “/etc/samba/smb.conf” for your environment. For example: Step 5:...

  • Page 196: Figure B-43: Disable Automatically Restart

    Figure B-43: Disable Automatically Restart Step 2: Configure the following BIOS options of the client system. Advanced → iEi Feature → Auto Recovery Function → Enabled Advanced → iEi Feature → Recover from PXE → Enabled Boot → Launch PXE OpROM → Enabled...
  • Page 197 KINO-DQM871 Mini-ITX SBC MUST be installed in the system, otherwise, the system will automatically restore from the factory default image every ten (10) minutes. Step 6: Restart the client system from LAN. If the system encounters a Blue Screen of Death (BSoD) or a hang for around 10 minutes, it will automatically restore from the factory default image.

  • Page 198: Other Information

    KINO-DQM871 Mini-ITX SBC NOTE: A firewall or a SELinux is not in use in the whole setup process described above. If there is a firewall or a SELinux protecting the system, modify the configuration information to accommodate them. B.7 Other Information B.7.1 Using AHCI Mode or ALi M5283 / VIA VT6421A Controller...
  • Page 199 KINO-DQM871 Mini-ITX SBC Step 5: When the following window appears, press <S> to select “Specify Additional Device”. Page 184...

  • Page 200: System Memory Requirement

    KINO-DQM871 Mini-ITX SBC Step 6: In the following window, select a SATA controller mode used in the system. Then press <Enter>. The user can now start using the SATA HDD. Step 7: After pressing <Enter>, the system will get into the recovery tool setup menu.

  • Page 201: C Terminology

    KINO-DQM871 Mini-ITX SBC Appendix Terminology Page 186...
  • Page 202 KINO-DQM871 Mini-ITX SBC AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and Power Interface (ACPI) is an OS-directed configuration, power management, and thermal management interface. AHCI Advanced Host Controller Interface (AHCI) is a SATA Host controller register-level interface.
  • Page 203 KINO-DQM871 Mini-ITX SBC Direct Memory Access (DMA) enables some peripheral devices to bypass the system processor and communicate directly with the system memory. DIMM Dual Inline Memory Modules are a type of RAM that offer a 64-bit data bus and have separate electrical contacts on each side of the module.
  • Page 204 KINO-DQM871 Mini-ITX SBC Liquid crystal display (LCD) is a flat, low-power display device that consists of two polarizing plates with a liquid crystal panel in between. LVDS Low-voltage differential signaling (LVDS) is a dual-wire, high-speed differential electrical signaling system commonly used to connect LCD displays to a computer.

  • Page 205: D Digital I/O Interface

    KINO-DQM871 Mini-ITX SBC Appendix Digital I/O Interface Page 190...

  • Page 206: Introduction

    KINO-DQM871 Mini-ITX SBC D.1 Introduction The DIO connector on the KINO-DQM871 is interfaced to GPIO ports on the Super I/O chipset. The DIO has both 4-bit digital inputs and 4-bit digital outputs. The digital inputs and digital outputs are generally control signals that control the on/off circuit of external devices or TTL devices.

  • Page 207: Assembly Language Samples

    KINO-DQM871 Mini-ITX SBC D.3 Assembly Language Samples D.3.1 Enable the DIO Input Function The BIOS interrupt call INT 15H controls the digital I/O. An assembly program to enable digital I/O input functions is listed below. AX, 6F08H Sets the digital port as input Initiates the INT 15H BIOS call D.3.2 Enable the DIO Output Function...

  • Page 208: E Hazardous Materials Disclosure

    KINO-DQM871 Mini-ITX SBC Appendix Hazardous Materials Disclosure Page 193...

  • Page 209: Hazardous Materials Disclosure Table For Ipb Products Certified As Rohs Compliant Under 2002/95/Ec Without Mercury

    KINO-DQM871 Mini-ITX SBC E.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
  • Page 210 KINO-DQM871 Mini-ITX SBC Part Name Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated Biphenyls Diphenyl (Pb) (Hg) (Cd) Chromium (CR(VI)) (PBB) Ethers (PBDE) Housing Display Printed Circuit Board Metal Fasteners Cable Assembly Fan Assembly Power Supply...
  • Page 211 KINO-DQM871 Mini-ITX SBC 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符 合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的 年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元 件将会单独标示出来。 部件名称 有毒有害物质或元素 铅 汞 镉 六价铬 多溴联苯 多溴二苯 醚 (Pb) (Hg) (Cd) (CR(VI)) (PBB) (PBDE) 壳体 显示 印刷电路板 金属螺帽 电缆组装 风扇组装 电力供应组装 电池 O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。 X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。...

Table of Contents