Standard / extended temperature
industrial motherboard in mini-itx form factor with intel haswell processors and hm87 / qm87 express chipset (63 pages)
Advanced Menu ..................36 Boot Menu ....................40 Chipset Menu ..................41 Power Menu ................... 43 Security Menu ..................44 Exit Menu ....................44 Chapter 5 Driver Installation .................. 46 KEEX-4030 User’s Manual...
Figure 7 Secure the processor in the socket ......31 Figure 8 Align the SO-DIMM Memory Module with the onboard socket ..33 Figure 9 Press down on the SO-DIMM Memory Module to lock it in place ..33 KEEX-4030 User’s Manual...
Page 6
Table 40 Boot Menu ........40 Table 41 Chipset Menu ........41 Table 42 Video Function Configuration ......42 Table 43 Power Menu ........43 Table 44 Security Menu ........44 Table 45 Exit Menu ........44 KEEX-4030 User’s Manual...
Use extreme caution when installing or removing components. Refer to the installation instructions in this user’s guide for precautions and procedures. If you have any questions, please contact Quanmax Post-Sales Technical Support. WARNING High voltages are present inside the chassis when the unit’s power cord is...
Static electricity can harm system boards. Perform service at an ESD workstation and follow proper ESD procedure to reduce the risk of damage to components. Quanmax strongly encourages you to follow proper ESD procedure, which can include wrist straps and smocks, when servicing equipment.
Page 9
Handle components and boards with care. Don’t touch the components or contacts on a board. Hold a board by its edges or by its metal mounting bracket. Do not handle or store system boards near strong electrostatic, electromagnetic, magnetic, or radioactive fields. KEEX-4030 User’s Manual...
Remove all items from the box. If any items listed on the purchase order are missing, notify Quanmax customer service immediately. Inspect the product for damage. If there is damage, notify Quanmax customer service immediately. Refer to “Warranty Policy” for the return procedure.
Quanmax or its authorized agent; or if the failure is caused by accident, acts of God, or other causes beyond the control of Quanmax or the manufacturer. Neglect, misuse, and abuse shall include any installation, operation, or maintenance of the product other than in accordance with the user’s guide.
Quanmax. Limitation of Liability In no event shall Quanmax be liable for any defect in hardware, software, loss, or inadequacy of data of any kind, or for any direct, indirect, incidental, or consequential damages in connection with or arising out of the performance or use of any product furnished hereunder.
Page 13
AC power cord. Surge protectors, however, do not offer protection against brownouts, which occur when the voltage drops more than 20 percent below the normal AC line voltage level. KEEX-4030 User’s Manual...
Page 14
Surge protectors should be used with all UPS systems, and the UPS system should be Underwriters Laboratories (UL) safety approved. KEEX-4030 User’s Manual...
Chapter 1 Introduction Overview The KEEX-4030 is an ECX Form Factor embedded single board computer (SBC) that combines the high performance Intel® Core™2 Duo processor with Intel® GM45/ ICH9M chipset and supports DDR3 SODIMM up to 4GB. This SBC offers the...
No.1. To move a jumper from one position to another, use needle-nose pliers or tweezers to pull the pin cap off the pins and move it to the desired position. KEEX-4030 User’s Manual...
Chapter 2 Jumper Settings and Pin Definitions For jumper and connector locations, please refer to the diagrams below. Figure 4 Jumper and Connector Locations KEEX-4030 User’s Manual...
Panel Power = +3.3V (Default) Panel Power = +5V Table 6 JP4 Clear ME RTC Registers Jumper Status Open Normal Operation (Default) Short Clear ME RTC Registers Table 7 JP5 Backlight Enable Selection Jumper Status Active High (Default) Active Low KEEX-4030 User’s Manual...
Table 9 DVI (DVI-I Connector) Signal Name Signal Name TX2N TX2P TX5N TX5P SD_CLK SD_DATA VSYNC TX1N TX1P TX4N TX4P VGA_PWR VGA_EN TX0N TX0P TX6N TX6P TCLP TXLN Signal Name Analog red Analog green Analog blue Analog horizontal sync Analog ground KEEX-4030 User’s Manual...
RTS, Request to send CTS, Clear to send RI, Ring indicator Table 12 LAN1 (10/100/1000 Ethernet RJ-45 Connector) Signal Table 13 USB1 (USB2.0 Port 0, 1 Type A Connector) Signal Name Signal Name USB1- USB0- USB1+ USB0+ KEEX-4030 User’s Manual...
IDE Data 3 IDE Data 11 IDE Data 4 IDE Data 12 IDE Data 5 IDE Data 13 IDE Data 6 IDE Data 14 IDE Data 7 IDE Data 15 IDE Chip select 1# IDE Chip select 3# KEEX-4030 User’s Manual...
Table 18 CN2, Digital Input / Output Pin Header Signal Signal Digital Output 0 Digital Input 0 Digital Output 1 Digital Input 1 Digital Output 2 Digital Input 2 Digital Output 3 Digital Input 3 Pitch:2.0mm [YIMTEX 3292*05SAGR(6T)] KEEX-4030 User’s Manual...
RTS, Request to send TXD, Transmit data CTS, Clear to send DTR, Data terminal ready RI, Ring indicator GND, ground 10 +5V Pitch:1.25mm [YIMTEX 501MW1*10STR] Table 22 FAN1, CPU FAN Wafer Signal +12V FAN_RPM Pitch:2.54mm YIMTEX 521AW1*03STR KEEX-4030 User’s Manual...
7P+15P MALE 180D SATA CONNECTOR BLACK [WIN WIN WATH-22DLBGU4] Table 27 SATA2, Serial ATA Connector Signal Name 7P 180D SATA CONNECTOR BLUE [FOXCONN LD1807V-S52U] Table 28 USB2, USB2.0 Port 2, 3 Pin Header Signal Name Signal Name USB2- USB3- USB2+ USB3+ Pitch:2.54mm [YIMTEX 3322*05SAGR(6T) -09] KEEX-4030 User’s Manual...
Carefully follow the steps below in order to install the CPU: Check and confirm that you are installing the correct CPU type. Using a screwdriver, disengage (open) the socket actuator, as shown in figure below. Figure 5 Disengage the socket actuator KEEX-4030 User’s Manual...
Removing the CPU: To remove the CPU, reverse the installation steps. Before removing the CPU, turn off the system power and wait for about 20 minutes until the heat radiation plate of the cooling fan and the CPU cools KEEX-4030 User’s Manual...
CPU, causing damage. Note: Fan less Operation: In order to operate the KEEX-4030 without a fan, the cooling solution must be integrally designed with the chassis. Contact Quanmax for more information on fan less operation.
SO-DIMM. Lift it out of the socket. Note: Make sure you store the SO-DIMM in an anti-static bag. The socket must be populated with memory modules of the same size and manufacturer. KEEX-4030 User’s Manual...
NOTE: The BIOS menus and selections for your product may vary from those in this chapter. For the BIOS manual specific to your product, please contact Quanmax. AMI's ROM BIOS provides a built-in Setup program, which allows the user to modify the basic system configuration and hardware parameters.
LBA/ Large Mode [Auto] DMA Mode [Auto] <> Select Screen S.M.A.R.T [Auto] ↑↓ Select Item +- Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.61 (C)Copyright 1985-2006, American Megatrends, Inc. KEEX-4030 User’s Manual...
↑↓ Select Item > SuperIO Configuration +- Change Field > OnBoard Peripherals Configuration Tab Select Field > iTPM function F1 General Help > Hardware Health Configuration F10 Save and Exit ESC Exit V02.61 (C)Copyright 1985-2006, American Megatrends, Inc. KEEX-4030 User’s Manual...
GbE Controller [Enabled] GbE LAN Boot [Disabled] <> Select Screen HDA Controller [Enabled] ↑↓ Select Item +- Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.61 (C)Copyright 1985-2006, American Megatrends, Inc. KEEX-4030 User’s Manual...
Page 38
Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.61 (C)Copyright 1985-2006, American Megatrends, Inc. TCG/TPM SUPPORT [No] Options: No, Yes If the value is Enabled. Execute TPM Command [Don’t change] Options: Don’t change, Disabled, Enabled KEEX-4030 User’s Manual...
Page 39
:11.182 V ESC Exit 5VSB : 4.945 V VBAT :3.344 V V02.61 (C)Copyright 1985-2006, American Megatrends, Inc. CPU Warning Temperature [Disabled] Options: Disabled, 80°C/176°F, 85°C/185°F, 90°C/194°F, 95°C/203°F CPU Shutdown Temperature [Disabled] Options: Disabled, 80°C/176°F, 85°C/185°F, 90°C/194°F, 95°C/203°F KEEX-4030 User’s Manual...
When set to Enabled, the system waits for F1 key to be pressed when error occurs. Options: Disabled, Enabled Hit ‘DEL’ Message Display [Enabled] When set to Enabled, the system displays the message ‘Press DEL to run Setup’ during POST. Options: Disabled, Enabled KEEX-4030 User’s Manual...
Select the amount of system memory used by the Internal graphics device. Options: Enabled 32MB, Enabled 64MB, Enabled 128MB Gfx Low Power Mode [Disabled] This option is applicable for SFF only. Options: Disabled, Enabled Press <Enter> to select a sub-menu for Video Function Configuration. KEEX-4030 User’s Manual...
Page 42
Flat Panel Type [1024x768 18 Bit 1CH] Options: 640x480 18 Bit 1CH 1024x768 18 Bit 1CH 800x600 18 Bit 1CH 1280x800 18 Bit 1CH HDCP Support [Disabled] Options: Disabled, Enabled Panel BackLight Voltage [2.5] Options: Min 0.0V, Max: 5.0V KEEX-4030 User’s Manual...
Enable/ Disable USB Device Wakeup From S3/S4 Options: Disabled, Enabled GbE Wake Up Form S5 [Disabled] Options: Disabled, Enabled Resume On RTC Alarm [Disabled] Options: Disabled, Enabled If the value is Enabled. RTC Alarm Date (Days) [Every Day] KeyIn “+”/”-“ to select KEEX-4030 User’s Manual...
<> Select Screen Discard Changes and Exit ↑↓ Select Item Discard Changes +- Change Field Tab Select Field Load Optimal Defaults F1 General Help Load Failsafe Defaults F10 Save and Exit ESC Exit V02.61 (C)Copyright 1985-2006, American Megatrends, Inc. KEEX-4030 User’s Manual...
Page 45
Load Optimal Default values for all the setup values. This option allows you to load failsafe default values for each of the parameters on the Setup menus, which will provide the most stable performance settings. The F8 key can be used for this operation. KEEX-4030 User’s Manual...
Chapter 5 Driver Installation If your KEEX-4030 does not come with an operating system pre-installed, you will need to install an operating system and the necessary drivers to operate it. After you have finished assembling your system and connected the appropriate power source, power it up using the power supply and install the desired operating system.