Subscribe to Our Youtube Channel
Related Manuals for Quanmax KEMF-4010
Summary of Contents for Quanmax KEMF-4010
- Page 1 KEMF-4010 FlexATX Embedded Motherboard with AMD Athlon™ Single and Dual-Core Processors and AMD® 780E + SB710 chipset User’s Guide KEMF-4010 User’s...
- Page 2 © 2009 Quanmax Inc. All rights reserved. The information in this user’s guide is provided for reference only. Quanmax does not assume any liability arising out of the application or use of the information or products described herein. This user’s guide may contain or reference information and products protected by copyrights or patents and does not convey any license under the patent rights of Quanmax, nor the rights of others.
-
Page 3: Table Of Contents
Processor Handling ..................35 Installing the CPU ..................35 Removing the CPU: ................... 36 Cooler Installation ................... 37 Memory Module Installation ..............38 Installing a DIMM ..................39 Removing a DIMM: ..................40 Expansive Interfaces ................40 KEMF-4010 User’s... - Page 4 Power Menu ................... 50 Security Menu ..................51 Exit Menu ....................52 Chapter 5 Driver Installation .................. 53 Appendix A DIO (Digital I/O) Programming Guide ............ 54 Appendix B WatchDog Timer Sample Code ............. 55 KEMF-4010 User’s...
-
Page 5: Figures
Figure 1 Block Diagram .................... 16 Figure 2 KEMF-4010 Mechanical Dimensions ............17 Figure 3 Jumper Connector ..................18 Figure 4 KEMF-4010 Jumper and Connector Locations .......... 19 Figure 5 CPU alignment in Socket AM2 ..............35 Figure 6 CPU Installation ..................36 Figure 7 Place the CPU cooler on the retention frame .......... -
Page 6: Tables
Tables Tables Table 1 KEMF-4010 Specification ........15 Table 2 Jumper List ..........20 Table 3 JP1, JP2, JP3, JP6, JP7, JP13, COM Port Signal / Power Selection ..20 Table 4 JP4, DIO Signal / Power Selection ......20 Table 5 JP5, Parallel Port Signal Selection ...... - Page 7 Table 53 Chipset Setting Menu ........48 Table 54 DRAM Timing Configuration ........ 49 Table 55 Power Menu ........... 50 Table 56 Wake Up Event Setup ........50 Table 57 Security Menu .......... 51 Table 58 Exit Menu ..........52 KEMF-4010 User’s...
-
Page 8: Safety Instructions
Use extreme caution when installing or removing components. Refer to the installation instructions in this user’s guide for precautions and procedures. If you have any questions, please contact Quanmax Post-Sales Technical Support. WARNING High voltages are present inside the chassis when the unit’s power cord is plugged into... -
Page 9: Preventing Electrostatic Discharge
Static electricity can harm system boards. Perform service at an ESD workstation and follow proper ESD procedure to reduce the risk of damage to components. Quanmax strongly encourages you to follow proper ESD procedure, which can include wrist straps and smocks, when servicing equipment. -
Page 10: Preface
Remove all items from the box. If any items listed on the purchase order are missing, notify Quanmax customer service immediately. Inspect the product for damage. If there is damage, notify Quanmax customer service immediately. Refer to “Warranty Policy” for the return procedure. -
Page 11: Warranty Policy
Quanmax or its authorized agent; or if the failure is caused by accident, acts of God, or other causes beyond the control of Quanmax or the manufacturer. Neglect, misuse, and abuse shall include any installation, operation, or maintenance of the product other than in accordance with the user’s guide. -
Page 12: Maintaining Your Computer
Quanmax. Limitation of Liability In no event shall Quanmax be liable for any defect in hardware, software, loss, or inadequacy of data of any kind, or for any direct, indirect, incidental, or consequential damages in connection with or arising out of the performance or use of any product furnished hereunder. - Page 13 Surge protectors should be used with all UPS systems, and the UPS system should be Underwriters Laboratories (UL) safety approved. KEMF-4010 User’s...
-
Page 14: Chapter 1 Introduction
Chapter 1 Introduction Overview The KEMF-4010 is a FlexATX embedded motherboard that built with the fastest onboard graphics - AMD® 780E and supporting AMD Athlon™ X2 dual-core processor and DDR2 DIMM up to 8GB. This embedded board offers the latest video performance and I/O interfaces at an extremely attractive price/performance ratio and measures 229 x 191mm, a 42 percent space reduction over ATX boards. -
Page 15: Product Specifications
CPU and system temperature Monitor CPU and system fan speed Dimensions FlexATX (229 x 191 mm) Operation Temp: 0ºC - 60ºC Environmental Storage Temp.: -10ºC - 85ºC Factors Humidity: 0% - 90% Certifications CE, FCC Class A Table 1 KEMF-4010 Specification KEMF-4010 User’s... -
Page 16: System Block Diagram
Chapter 1 System Block Diagram Figure 1 Block Diagram KEMF-4010 User’s... -
Page 17: Mechanical Dimensions
Chapter 1 Mechanical Dimensions Figure 2 KEMF-4010 Mechanical Dimensions KEMF-4010 User’s... -
Page 18: Chapter 2 Hardware Settings
2 and 3 are connected and so on. You will see that one of the lines surrounding a jumper pin is thick, which indicates pin No.1. To move a jumper from one position to another, use needle-nose pliers or tweezers to pull the pin cap off the pins and move it to the desired position. KEMF-4010 User’s... -
Page 19: Jumper Settings And Pin Definitions
Chapter 2 Jumper Settings and Pin Definitions For jumper and connector locations, please refer to the diagrams below. Figure 4 KEMF-4010 Jumper and Connector Locations KEMF-4010 User’s... -
Page 20: Jumper Settings
JP1,JP2,JP3,JP6,JP7 : Pitch: 2.54mm NY 6T[YIMTEX 3362*05SANGR] JP13: Pitch: 2.54mm [YIMTEX 3322*05SAGR(6T] Cable : 0C501P040926000L COM Port cable, 10-pin 2.54mm to DB-9 connector with bracket, L=26cm Table 4 JP4, DIO Signal / Power Selection Jumper Status +5V(Default) +12V Pitch: 2.54mm [YIMTEX 3321*03SAGR(6T)] KEMF-4010 User’s... -
Page 21: Table 5 Jp5, Parallel Port Signal Selection
Table 8 JP11, Panel Power Selection Jumper Status +3.3V(Default) Pitch: 2.54mm [YIMTEX 3321*03SAGR(6T)] Note： If DVI cable is connecting to LVDS panel connector, the Pin2-3 should be shorted. Table 9 JP12, Backlight Power Selection Jumper Status +12V(Default) Pitch: 2.54mm [YIMTEX 3321*03SAGR(6T)] KEMF-4010 User’s... -
Page 22: Rear Panel Pin Assignments
LAN2 & USB2.0 Port 4,5 Connector PS2-KBMS1 PS/2 KB/MS Mini-DIN Connector HDMI1 HDMI Connector Table 13 AUDIO1, 3 Stack-up HD Audio Phone Jack Signal Name BLUE LINE IN GREEN LINE OUT PINK MIC IN [Foxconn JA33331-H11P-4F] *Support Jack re-tasking & multi-streaming KEMF-4010 User’s... -
Page 23: Table 14 Vga_Com1, Rs-232 / 422 / 485 Port 1 Db15+Db9 Connector
YLED- [UDE RU1-161F9WGF(XB)] Table 16 LAN LED Status Status Orange / Green Yellow No link 10M link 10M active Blink 100M link Green on 100M active Green on Blink 1000M link Orange on 1000M active Orange on Blink KEMF-4010 User’s... -
Page 24: Table 17 Ps2-Kbms1, Ps/2 Kb/Ms Mini-Din Connector
TMDS Clock Shield TMDS Clock– Reserved DDC/CEC Ground +5 V Power Hot Plug Detect [KUON YI HDMI-KRPS00-A03N2-L] *：BIOS Auto detect HDMI or PCIE mode ** Note: When HDMI is occupied, the PCIe x16 slot will support PCIe x8 only. ** KEMF-4010 User’s... -
Page 25: Main Board Pin Assignments
Mini PCIe Connector CHA_FAN1 System FAN Wafer IrDA Pin Header CHA_FAN2 System FAN Wafer Table 20 ATXPWR1, 24-pin ATX Power Input Connector Signal Signal +3.3V +3.3V +3.3V -12V PS_ON POWER OK +5VSB +12V +12V +3.3V DIP 12P*2.180D(M) [YIMTEX 576MWA2*12STR] KEMF-4010 User’s... -
Page 26: Table 21 Atx12V1, 4-Pin Atx Power Input Connector
Table 23 C0M2, COM3, COM4, COM5, COM6, RS-232 Box Header Signal DCD, Data carrier detect RXD, Receive data TXD, Transmit data DTR, Data terminal ready GND, ground DSR, Data set ready RTS, Request to send CTS, Clear to send RI, Ring indicator Pitch: 2.54mm [YIMTEX 32510SAG1R(6T)] KEMF-4010 User’s... -
Page 27: Table 24 Dio1, Digital Input / Output Pin Header
Note：BL_ADJ can be setting from 0V to 5V in BIOS setup. Table 27 AMP_L1, AMP_R1, 2 W Audio AMP Output Wafer Signal Name Speaker+ Speaker- Pitch=2.0mm WAFER [YIMTEX 503PW1*02STR] Table 28 CD1, CD-ROM Audio Input Wafer Signal Name CD-IN-R CD-IN-L P-2.54mm WAFER [YIMTEX 522CW4SGR] KEMF-4010 User’s... -
Page 28: Table 29 Cpu_Fan1, Fan Wafer
Note：Internal Buzzer is enabled when Pin6-8 is shorted. Table 32 FP2, Front Panel 2 Pin Header Signal Signal Power LED + Power Button + Power Button - Power LED - Keyboard Lock SMBus Data SMBus Clock Pitch: 2.54mm [YIMTEX 3322*05SAGR(6T] KEMF-4010 User’s... -
Page 29: Table 33 Lvds1, Lvds Panel Connector
IrDA Pin Header Signal Name Pitch: 2.54mm [YIMTEX 3321*05SAGR-02] Table 35 PCI1, 32-bit / 33Mhz / 5V-key PCI Slot Side B Side A -12V Reserved Reserved +12V Ground Reserved Reserved Reserved INTA# INTB# INTC# INTD# Reserved GNT1# * REQ1# * KEMF-4010 User’s... - Page 30 AD[14] +3.3V Ground AD[13] AD[12] AD[11] AD[10] Ground Ground AD[09] AD[08] C/BE[0]# AD[07] +3.3V +3.3V AD[06] AD[05] AD[04] AD[03] Ground Ground AD[02] AD[01] AD[00] Reserved Reserved PCI 60*2P 180D (F) [FOXCONN EH06001-DAW-DF] *：Reserved for second PCI master device. KEMF-4010 User’s...
-
Page 31: Table 36 Pcie1, Standard Pci Express X16 Slot
Ground HSIP6 Ground HSIP6 HSOP7 Ground HSON7 Ground Ground HSIP7 PRSNT#3 HSIP7 Ground Ground HSOP8 Reserved HSON8 Ground Ground HSIP8 Ground HSIP8 HSOP9 Ground HSON9 Ground Ground HSIP9 Ground HSIP9 HSOP10 Ground HSON10 Ground Ground HSIP10 Ground HSIP10 KEMF-4010 User’s... -
Page 32: Table 37 Usb1, Usb2, Usb2.0 Pin Header
PD5, parallel data 5 Ground PD6, parallel data 6 Ground PD7, parallel data 7 Ground ACK, acknowledge Ground Busy Ground Paper empty Ground Select Pitch:2.0mm NY 6T [YIMTEX 32626MAGR] Cable 0C501P042526000L CABLE, FLAT DB25P MALE/IDC 26P 2.0mm 26CM W/BRACKET KEMF-4010 User’s... -
Page 33: Table 39 Pcie2, Pcie3, Standard Pci Express X1 Slot
A RAID 10 configuration requires at least four hard drives and the total number of hard drives must be an even number. KEMF-4010 User’s... -
Page 34: Table 41 Mpcie1, Mini Pcie Connector
Reserved Ground Reserved W_disable# Ground PERST# PERn0 +3VSB PERp0 Ground Ground +1.5V Ground SMB_CLK PETn0 SMB_DATA PETp0 Ground Ground USB_D- Reserved USB_D+ Reserved Ground Reserved LED_WWAN# Reserved LED_WAN# Reserved LED_WPAN# Reserved +1.5V Reserved Ground Reserved +3.3V [FOXCONN AS0B226-S56N-7F] KEMF-4010 User’s... -
Page 35: Chapter 3 System Installation
Check and confirm that you are installing the correct CPU type. Completely lift up the CPU socket locking lever. Align the gold triangle on the CPU with the similar marking on the socket (see figure below). Figure 5 CPU alignment in Socket AM2 KEMF-4010 User’s... -
Page 36: Removing The Cpu
To remove the CPU, follow Step 2 of Installing the CPU above. Remove the CPU by grasping the substrate edges only with thumb and forefinger and lifting it out with a purely vertical motion. WARNING The CPU and the heat-sink may be hot and could cause burns. KEMF-4010 User’s... -
Page 37: Cooler Installation
Hook the CPU cooler clip to the mounting lug on one side of the retention frame. On the other side, push straight own on the CPU cooler clip to hook it to the mounting lug on the retention frame. Figure 8 Hook the CPU cooler clip to the mounting lug KEMF-4010 User’s... -
Page 38: Memory Module Installation
DDR2 DIMMs have 240-pins and one notch that will match with the onboard DIMM sockets. DIMM modules are installed by placing the chip firmly into the socket at a 90-degree angle and pressing straight down until it fits tightly into the DIMM socket. KEMF-4010 User’s... -
Page 39: Installing A Dimm
Do not touch the connectors of the DIMM. Dirt or other residue may cause a malfunction. Hold the DIMM with its notch aligned with the memory socket of the KEMF-4010 and insert it completely into the socket. Lift the locking tabs at each end of the DIMM socket to lock it in position. -
Page 40: Removing A Dimm
When adding or removing expansion cards, make sure that you unplug the power supply first. Meanwhile, read the documentation for the expansion card to configure any necessary hardware or software settings for the expansion card, such as jumpers, switches or BIOS configuration. KEMF-4010 User’s... -
Page 41: Chapter 4 Ami Bios Setup
The BIOS menus and selections for your product may vary from those in this chapter. For the BIOS manual specific to your product, please contact Quanmax. AMI's ROM BIOS provides a built-in Setup program, which allows the user to modify the basic system configuration and hardware parameters. -
Page 42: Main Menu
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc. LBA/ Large Mode [Auto] Enables or disables the LBA (Logical Block Addressing)/ Large mode. Setting to Auto enables the LBA mode if the device supports this mode, and if the device was KEMF-4010 User’s... -
Page 43: Advanced Menu
> Hardware Health Configuration ESC Exit V02.61 (C)Copyright 1985-2006, American Megatrends, Inc. Press <Enter> to select a sub-menu for detailed options. Quick Boot [Enabled] Enabling this item allows BIOS to skip some Power On Self Tests (POST) while KEMF-4010 User’s... -
Page 44: Table 46 Cpu Feature
F1 General Help F10 Save and Exit ESC Exit V02.61 (C)Copyright 1985-2006, American Megatrends, Inc. Cool’n’Quiet [Enabled] Enable/disable the generation of APCI_PPC, _PPS and _PCT objects. Options: Enable, Disabled C1E Support [Disabled] Spread Spectrum [Enabled] Options: Enable, Disabled KEMF-4010 User’s... -
Page 45: Table 47 Onboard Peripherals Configuration Settings
On-Chip ATA Configuration Disabled OnChip SATA Channel [Enabled] Enabled OnChip SATA Type [IDE] <> Select Screen ↑↓ Select Item +- Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.61 (C)Copyright 1985-2006, American Megatrends, Inc. KEMF-4010 User’s... -
Page 46: Table 49 Onboard I/O Configuration
Options: Disabled, 3F8, 2F8, 3E8, 2E8, 2F0, 2E0 COM4 IRQ [11] Options: 3, 4, 11 COM5 Address [228] Options: Disabled, 3F8, 2F8, 3E8, 2E8, 228 220 COM5 IRQ [5] Options: 3, 4, 5, 6, 7, 11 COM5 Mode [Normal] KEMF-4010 User’s... -
Page 47: Table 50 Trusted Computing
:3199 RPM +- Change Field Tab Select Field CPU Core :1.200 V F1 General Help +3.30V :3.166 V F10 Save and Exit +5.00V :4.958 V ESC Exit +12.0V :11.182 V 5VSB :4.972 V V02.61 (C)Copyright 1985-2006, American Megatrends, Inc. KEMF-4010 User’s... -
Page 48: Boot Menu
F10 Save and Exit > DRAM Timing Configuration ESC Exit V02.61 (C)Copyright 1985-2006, American Megatrends, Inc. Primary Video Controller [PCI-E] Options: PCI-E, PCI, Internal VGA Share Memory [Auto] Options: Auto, 32MB, 64MB, 128MB, 256MB, 512MB Surround View [Auto] KEMF-4010 User’s... -
Page 49: Table 54 Dram Timing Configuration
Memory Clock Mode [Auto] Options: Auto, Limit, Manual If this option is Manual, the Memory clock value can be selected. Memclock Value [200MHz] Options: 200MHz, 266 MHz, 333 MHz, 400 MHz, 533 MHz DRAM Timing Mode [Auto] Options: Auto, DCT 0 KEMF-4010 User’s... -
Page 50: Power Menu
[Disabled] Resume by PCIE Device [Disabled] <> Select Screen Resume by RTC Alarm [Disabled] ↑↓ Select Item +- Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.61 (C)Copyright 1985-2006, American Megatrends, Inc. KEMF-4010 User’s... -
Page 51: Security Menu
Installed. Change User Password Select this item to set or change the user password. The User Password item on top of the screen displays the default Not Installed. After you have set a password, this item displays Installed. KEMF-4010 User’s... -
Page 52: Exit Menu
Load Optimal Default values for all the setup values. This option allows you to load failsafe default values for each of the parameters on the Setup menus, which will provide the most stable performance settings. The F8 key can be used for this operation. KEMF-4010 User’s... -
Page 53: Chapter 5 Driver Installation
Chapter 5 Driver Installation If your KEMF-4010 does not come with an operating system pre-installed, you will need to install an operating system and the necessary drivers to operate it. After you have finished assembling your system and connected the appropriate power source, power it up using the power supply and install the desired operating system. -
Page 54: Appendix A Dio (Digital I/O) Programming Guide
PCI Reg Reg A8h: bit 21--DIO_IN2 Reg A8h: bit 17--DIO_IN3 Reg A8h: bit 24--DIO_OUT0 Reg A8h: bit 2--DIO_OUT1 Reg 50h: bit 9--DIO_OUT2 Reg 50h: bit 10--DIO_OUT3 PCI Ext Reg Ext Addr Port(F8h)=00h Ext Data Port(FCh) bit 27--DIO_IN0 bit 26--DIO_IN1 KEMF-4010 User’s... -
Page 55: Appendix B Watchdog Timer Sample Code
Appendix B Appendix B WatchDog Timer Sample Code //============================================ //KEMF-4010 DOS watchdog sample program //Please compile with Turbo C 3.0 to utilized the program //============================================ int main(){ //Initialized the WDT program outp(0x2e,0x87); outp(0x2e,0x01); outp(0x2e,0x55); outp(0x2e,0x55); //Setting Logical Device Number to 0x07 outp(0x2e,0x07);...
Need help?
Do you have a question about the KEMF-4010 and is the answer not in the manual?
Questions and answers