Standard / extended temperature
industrial motherboard in mini-itx form factor with intel haswell processors and hm87 / qm87 express chipset (63 pages)
3.5" ecx single board computer with intel skylake / kaby lake u-series processors (60 pages)
Summary of Contents for Quanmax KEMX-1600 Series
Page 1
KEMX-1600 Series Industrial Motherboard in Mini-ITX form factor ® With Dual Core Intel Atom Processor D2550 ™ User’s Guide KEMX-1600 series User’s Manual...
Memory Module Installation ............... 42 Chapter 4 AMI BIOS Setup ..................43 Overview ....................43 Main Menu ....................44 Advanced Menu ..................45 Boot Menu ....................65 Security Menu .................... 66 Save & Exit Menu ..................66 KEMX-1600 series User’s Manual...
Page 4
Content Chapter 5 Driver Installation ................. 68 Appendix A DIO (Digital I/O) Sample Code ............69 Appendix B WatchDog Timer Sample Code ............73 KEMX-1600 series User’s Manual...
Figure 5 Rear Panel IO ................37 Figure 6 Expansion Interfaces ..............41 Figure 7 Align the SO-DIMM Memory Module with the onboard socket ..42 Figure 8 Press down on the SO-DIMM Memory Module to lock it in place 42 KEMX-1600 series User’s Manual...
Tables Tables Table 1 KEMX-1600 series Specification ........... 19 Table 2 Jumper List ..................24 Table 3 JP1 USB Power Selection ............. 24 Table 4 JP2 RTC Reset Selection .............. 24 Table 5 JP3 AT / ATX Mode Selection ............24 Table 6 JP4 Panel &...
Page 7
Table 60 Advanced Menu – Super IO Configuration – Serial Port 8 Configuration ................60 Table 61 Advanced Menu – Super IO Configuration – Serial Port 9 Configuration ................61 Table 62 Advanced Menu – Super IO Configuration – Serial Port 10 Configuration ................62 KEMX-1600 series User’s Manual...
Page 8
Table 63 Advanced Menu – Super IO Configuration – Parallel Port Configuration ................. 63 Table 64 Advanced Menu –H/W Monitor ............ 64 Table 65 Boot Menu ................... 65 Table 66 Security Menu ................66 Table 67 Save & Exit Menu ................ 66 KEMX-1600 series User’s Manual...
Use extreme caution when installing or removing components. Refer to the installation instructions in this user’s guide for precautions and procedures. If you have any questions, please contact Quanmax Post-Sales Technical Support. WARNING High voltages are present inside the chassis when the unit’s power cord is plugged into an electrical outlet.
Static electricity can harm system boards. Perform service at an ESD workstation and follow proper ESD procedure to reduce the risk of damage to components. Quanmax strongly encourages you to follow proper ESD procedure, which can include wrist straps and smocks, when servicing equipment.
Page 11
Handle components and boards with care. Don’t touch the components or contacts on a board. Hold a board by its edges or by its metal mounting bracket. Do not handle or store system boards near strong electrostatic, electromagnetic, magnetic, or radioactive fields. KEMX-1600 series User’s Manual...
Remove all items from the box. If any items listed on the purchase order are missing, notify Quanmax customer service immediately. Inspect the product for damage. If there is damage, notify Quanmax customer service immediately. Refer to “Warranty Policy” for the return procedure.
Quanmax or its authorized agent; or if the failure is caused by accident, acts of God, or other causes beyond the control of Quanmax or the manufacturer. Neglect, misuse, and abuse shall include any installation, operation, or maintenance of the product other than in accordance with the user’s guide.
Quanmax. Limitation of Liability In no event shall Quanmax be liable for any defect in hardware, software, loss, or inadequacy of data of any kind, or for any direct, indirect, incidental, or consequential damages in connection with or arising out of the performance or use of any product furnished hereunder.
Page 15
AC power is lost, the battery can provide power to the system for a limited amount of time, depending on the UPS system. UPS systems range in price from a few hundred dollars to several thousand KEMX-1600 series User’s Manual...
Page 16
Surge protectors should be used with all UPS systems, and the UPS system should be Underwriters Laboratories (UL) safety approved. KEMX-1600 series User’s Manual...
NM10 chipset. Featured are 1x DDR3 800/1066 SO-DIMM up to 4GB, 7xUSB2.0, 2xGbE LAN, 2xSATA,1x HDMI, 1xVGA,1x mini PCIe slot, HD audio. The KEMX-1600 series is a compact, high performance industrial motherboard that is ideal for a variety of applications.
AT / ATX power mode supported, default is ATX mode 0ºC – 60ºC (For KEMX-1600, KEMX-1603) Operation Temp. -20ºC – 70ºC- Wide Temperature ( For KEMX-160A) Certifications CE, FCC Class A Table 1 KEMX-1600 series Specification KEMX-1600 series User’s Manual...
No.1. To move a jumper from one position to another, use needle-nose pliers or tweezers to pull the pin cap off the pins and move it to the desired position. KEMX-1600 series User’s Manual...
Chapter 2 Jumper Settings and Pin Definitions For jumper and connector locations, please refer to the diagrams below. Figure 4 Jumper and Connector Locations KEMX-1600 series User’s Manual...
Table 4 JP2 RTC Reset Selection Jumper Status 1-2 Open Normal Operation 1-2 Short Clear RTC CMOS Pitch:2.54mm [YIMTEX 3321*02SAGR(6T)] Table 5 JP3 AT / ATX Mode Selection Jumper Status 1-2 Short ATX Mode 2-3 Short AT Mode Pitch:2.54mm [YIMTEX 3321*03SAGR(6T)] KEMX-1600 series User’s Manual...
Panel Power = +3.3V Panel Power = +5V Pitch:2.54mm [YIMTEX 3362*03SAGR] Table 8 JP6 Backlight Power Enable Selection for LVDS2 Jumper Setting Status Backlight Enable Voltage = +3.3V Backlight Enable Voltage = +5V Active High Active Low Pitch:2.0mm[PINREX 222-97-03GBB1] KEMX-1600 series User’s Manual...
PCI1 PCI Slot SATA1 Serial ATA Port 0 Connector SATA2 Serial ATA Port 1 Connector LPT1 Parallel Port Pin Header 10x COM ports ( For KEMX-1600 ) 6x COM ports ( For KEMX-1603, KEMX-160A) KEMX-1600 series User’s Manual...
+5V / +12V ** +5V / +12V ** BL_EN*** Pitch:1.25mm [Townes Enterprise 1250W-07T1-V] *:BL_ADJ can be setting from 0V to 5V in BIOS setup. **:Backlight Power can be selected by JP4. ***:BL_EN can be selected by JP7. KEMX-1600 series User’s Manual...
Table 23 CN12 Left Channel 2W Audio AMP Output Wafer Signal Name Speaker+ Speaker- Pitch:2.0mm [YIMTEX 503PW1*02STR] Table 24 CN13 USB2.0 Port 4, 5 Pin Header Signal Name Signal Name +USBVCC +USBVCC USB_A- USB_B- USB_A+ USB_B+ Pitch:2.54mm [YIMTEX 3362*05SANGR-09] KEMX-1600 series User’s Manual...
Table 29 LVDS1 Primary 24-bit, 1-channel LVDS Panel Connector Signal Name Signal Name VDD_EN +3.3V / +5V* TxclkA- TxclkA+ TxoutA0- TxoutA0+ TxoutA1- TxoutA1+ TxoutA2- TxoutA2+ TxoutA3- TxoutA3+ DDC_Data Pitch:1.25mm [HIROSE DF13-30DP-1.25(24)] *:LVDS1 panel power can be selected by JP4. KEMX-1600 series User’s Manual...
AD[01] AD[00] Ground AD[22] AD[21] AD[20] Reserved Reserved AD[19] Ground +3.3V AD[18] DIP PCI 60*2P 180D [DU 8790-20C0-1280] *:Reserved for second PCI master device. Table 33 SATA1 Serial ATA Port 0 Connector Signal Name [FOXCONN LD1807V-S52U] KEMX-1600 series User’s Manual...
Table 34 SATA2 Serial ATA Port 1 Connector Signal Name [FOXCONN LD1807V-S52U] Table 35 LPT1 Parallel Wafer Signal Name Signal Name #AFD #ERR #INIT #SLIN #ACK BUSY SLCT DIP 26P 2R MALE 180° Pitch:2.54mm .Remove PIN No.26 [PINREX 210-72-13GB11] KEMX-1600 series User’s Manual...
GREEN LINE OUT PINK MIC IN [Foxconn JA33331-H11P-4F] Table 38 CN4 LAN1 & USB2.0 Port 0,1 Connector Signal Signal MDI[0]+ +USBVCC MDI[0]- USB_A- MDI[1]+ USB_A+ MDI[1]- MDI[2]+ +USBVCC MDI[2]- USB_B- MDI[3]+ USB_B+ MDI[3]- [UDE RU1-161F9WGF (XB)] KEMX-1600 series User’s Manual...
DCD, Data carrier detect RXD, Receive data TXD, Transmit data DTR, Data terminal ready GND, ground DSR, Data set ready RTS, Request to send CTS, Clear to send RI, Ring indicator D-SUB 9P(M)&15S(19.05mm(F)FOR PC99 FOLLOW PANTONE COLOR[FAN YING D201B1N01002N] KEMX-1600 series User’s Manual...
Chapter 2 Table 42 CN13 COM Port 1, 2 Connector Half Duplex Full Duplex Port RS-232 RS-422 RS-485 RS-485 DATA- DATA+ Port RS-232 [FAN YING D20HB1102112PN] Note:RS-232 / 422 / 485 can be selected in BIOS setup. KEMX-1600 series User’s Manual...
When adding or removing expansion cards, make sure that you unplug the power supply first. Meanwhile, read the documentation for the expansion card to configure any necessary hardware or software settings for the expansion card, such as jumpers, switches or BIOS configuration. KEMX-1600 series User’s Manual...
SO-DIMM. Lift it out of the socket. Make sure you store the SO-DIMM in an anti-static bag. The socket must be populated with memory modules of the same size and manufacturer. KEMX-1600 series User’s Manual...
This chapter provides a description of the AMI BIOS. The BIOS setup menus and available selections may vary from those of your product. For specific information on the BIOS for your product, please contact Quanmax. NOTE: The BIOS menus and selections for your product may vary from those in this chapter.
F1: General Help F2: Previous Values Total Size 2048 MB F3: Optimized Defaults Frequency 1067 MHz (DDR3) F4 Save & Exit System date [Thu 03/08/2012] ESC Exit System time [15:58:19] Version 2.14.1219. Copyright (C) 2011, American Megatrends, Inc. KEMX-1600 series User’s Manual...
F4 Save & Exit ESC Exit Version 2.14.1219. Copyright (C) 2011, American Megatrends, Inc. Legacy USB Support Options: Disabled, Enabled, Auto EHCI hand-off Options: Disabled, Enabled Mass Storage Device Options: Auto, Floppy, Forced FDD, Hard Disk, CD-ROM KEMX-1600 series User’s Manual...
+- Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4 Save & Exit ESC Exit Version 2.14.1219. Copyright (C) 2011, American Megatrends, Inc. CPU Warning Temperature Options: Disabled, 80 ºC , 85 ºC, 90 ºC KEMX-1600 series User’s Manual...
F3: Optimized Defaults F4 Save & Exit ESC Exit Version 2.14.1219. Copyright (C) 2011, American Megatrends, Inc. Full Screen LOGO Display Options: Disabled, Enabled Bootup Numlock State Options: On, Off Boot Option #1 Options: UEFI, SATA PM: Disabled KEMX-1600 series User’s Manual...
CMOS RAM. The CMOS RAM is sustained by an onboard backup battery and stays on even when the PC is turned off. When you select this option, a confirmation window appears. Select [Yes] to save changes and exit. KEMX-1600 series User’s Manual...
Page 67
Load Optimal Default values for all the setup values. This option allows you to load failsafe default values for each of the parameters on the Setup menus, which will provide the most stable performance settings. The F8 key can be used for this operation. KEMX-1600 series User’s Manual...
After you have finished assembling your system and connected the appropriate power source, power it up using the power supply and install the desired operating system. You can download the drivers for the KEMX-1600 series from the Quanmax website www.quanmax.com and install as instructed there. For other operating systems, please contact Quanmax.
//Set WDT output through KRST //(0x72 bit6(1: Enable, 0: Disable)) outp(0x2E,0x72); value = inp(0x2F) & 0xBF; value = value | 0x40;//Enable WDT output outp(0x2F,value); //Set Timer Value //(0x73 Time of watchdog timer) outp(0x2E,0x73); outp(0x2F,0x14);//set to 20 sec (0x14) KEMX-1600 series User’s Manual...
Page 74
Appendix B //Exit the MB PnP Mode outp(0x2E,0x02); outp(0x2F,0x02); return 0; KEMX-1600 series User’s Manual...