Related Manuals for Korenix JetWave 2450 Series
Summary of Contents for Korenix JetWave 2450 Series
- Page 1 Korenix JetWave 2450 Series IEEE 802.11n Wireless Outdoor Access Point User Manual Version 1.0, Mar, 2010 www.korenix.com...
- Page 2 Korenix JetWave 2450 Series IEEE 802.11n Wireless Outdoor Access Point User’s Manual Copyright Notice Copyright © 2010 Korenix Technology Co., Ltd. All rights reserved. Reproduction in any form or by any means without permission is prohibited.
-
Page 3: About This Manual
About This Manual This user manual is intended to guide professional installer to install the JetWave 2450 and how to build the infrastructure centered on it. It includes procedures to assist you in avoiding unforeseen problems. Conventions For your attention on important parts, special characters and patterns are used in this manual: Note: This indicates an important note that you must pay attention to. -
Page 4: Federal Communication Commission Interference Statement
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. -
Page 5: Fcc Radiation Exposure Statement
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To avoid the possibility of exceeding radio frequency exposure limits, you shall beep a distance of at least 100cm between you and the antenna of the installed equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. -
Page 6: Table Of Contents
Content Chapter 1 Introduction......................... 1 Introduction............................1 Appearance ............................2 Key Features ............................2 Typical Application ..........................3 Chapter 2 Hardware Installation ......................4 Preparation before Installation......................4 Professional Installation Required ...................... 4 Safety Precautions..........................4 Installation Precautions........................5 Product Package..........................5 Hardware Installation.......................... - Page 7 Security Settings ..........................30 Access Control..........................32 WDS Settings............................ 33 Chapter 5 Management........................34 SNMP Management ......................... 34 Configure SNMPv3 User Profile ....................... 35 Password............................36 Upgrade Firmware..........................37 Backup/ Retrieve Settings ........................ 37 Restore Factory Default Settings ..................... 38 Reboot ..............................
- Page 8 Figure Figure 1 JetWave 2450 .......................... 2 Figure 2 Typical Application ........................3 Figure 3 Move the Cover........................7 Figure 4 Cable Connection ........................7 Figure 5 Seal the Bottom ........................8 Figure 6 Connect to PoE Injector ......................8 Figure 7 Complete Set ...........................
- Page 9 Figure 40 Connection........................... 40 Figure 41 Network Flow Statistics ......................41 Figure 15 MAC Address ........................43...
- Page 10 Table Table 1 JetWave 2450 Factory Default Settings .................. 13 Table 2 ACSII ............................45 Table 3 Public Software Name and Description................... 47...
-
Page 11: Chapter 1 Introduction
Chapter 1 Introduction Introduction Designed for outdoor environment application, the JetWave 2450 is a high-performance last-mile broadband solution that provides reliable wireless network coverage. As an IEEE 802.11b/g compliant wireless device, the JetWave 2450 is able to give stable and efficient wireless performance, while designed with IEEE 802.11n draft 2.0 standard and high output power makes it possible to deliver several times faster data rate then normal wireless device and higher bandwidth with longer range for outdoor applications. -
Page 12: Appearance
Appearance Figure 1 JetWave 2450 Key Features Compliant with IEEE 802.11b/g and IEEE 802.11n draft 2.0 as well Support Power over Ethernet (PoE) IP65 waterproof housing endures almost any harsh environments Dual operating modes including AP and Wireless Client Support 64/128-bit WEP and 802.1X, WPA, WPA2, WPA&WPA2,WPA-PSK, WPA2-PSK, and WPA-PSK&WPA2-PSK etc Support WMM and Quality of service (QoS) for enhanced performance Advanced management tools like SNMP... -
Page 13: Typical Application
Typical Application This section describes the typical applications of JetWave 2450. By default, it is set to AP mode which allows it to establish a wireless coverage; besides, it is also able to join any available wireless network under wireless client mode. The JetWave 2450 is able to deliver stable and efficient broadband connectivity for various applications. -
Page 14: Chapter 2 Hardware Installation
Chapter 2 Hardware Installation This chapter describes safety precautions and product information you have to know and check before installing JetWave 2450. Preparation before Installation Professional Installation Required Please seek assistance from a professional installer who is well trained in the RF installation and knowledgeable in the local regulations. -
Page 15: Installation Precautions
Installation Precautions To keep the JetWave 2450 well while you are installing it, please read and follow these installation precautions. Users MUST use a proper and well-installed surge arrestor and grounding kit with JetWave 2450; otherwise, a random lightening could easily cause fatal damage to JetWave 2450. (Lightning) DAMAGE IS NOT COVERED UNDER WARRNTY. - Page 16 Pole Mounting Ring Power Cord & PoE Injector Warning: Users MUST use the “Power cord & PoE Injector” shipped in the box with the JetWave 2450. Use of other options will cause damage to the JetWave 2450. Chapter 2 Hardware Installation Page 6...
-
Page 17: Hardware Installation
Hardware Installation Connect up The bottom of the JetWave 2450 is a movable cover. Grab the cover and pull it back harder to take it out as the figure shown below. Figure 3 Move the Cover Plug a standard Ethernet cable into the RJ45 port. Figure 4 Cable Connection Chapter 2 Hardware Installation Page 7... -
Page 18: Figure 5 Seal The Bottom
Slide the cover back to seal the bottom of the JetWave 2450. Figure 5 Seal the Bottom Plug the power cord into the DC port of the PoE injector as the following right picture shows. Figure 6 Connect to PoE Injector Chapter 2 Hardware Installation Page 8... -
Page 19: Figure 7 Complete Set
Plug the other side of the Ethernet cable as shown in Step 3 into the PoE port of the PoE injector and get the complete set ready. Figure 7 Complete Set Chapter 2 Hardware Installation Page 9... -
Page 20: Pole Mounting
Pole Mounting Turn the JetWave 2450 over. Put the pole mounting ring through the middle hole of it. Note that you should unlock the pole mounting ring with a screw driver before putting it through JetWave 2450 as the following right picture shows. Figure 8 Pole Mounting –... -
Page 21: Figure 10 Pole Mounting – Step 3
Now you have completed the hardware installation of JetWave 2450. Figure 10 Pole Mounting – Step 3 Chapter 2 Hardware Installation Page 11... -
Page 22: Using The External Antenna
Using the External Antenna If you prefer to use the external antenna with N-type connector for your application instead of the built-in directional antenna, please follow the steps below. Grab the black rubber on the top of JetWave 2450, and slightly pull it up. The metal N-type connector will appear. -
Page 23: Chapter 3 Basic Settings
Chapter 3 Basic Settings Factory Default Settings We’ll elaborate the JetWave 2450 factory default settings. You can re-acquire these parameters by default. If necessary, please refer to the “Restore Factory Default Settings”. Table 1 JetWave 2450 Factory Default Settings Features Factory Default Settings Username admin... -
Page 24: System Requirements
Wireless Separation Disable Access Control Disable Enable/Disable Enable Read Community Name Public SNMP Write Community Name Private IP Address 0.0.0.0 System Requirements Before configuration, please make sure your system meets the following requirements: A computer coupled with 10/ 100 Base-TX adapter; Configure the computer with a static IP address of 192.168.1.x, as the default IP address of JetWave 2450 is 192.168.1.1. -
Page 25: Figure 13 Main
Enter the username (Default: admin) and password (Default: password) respectively and click “Login” to login the main page of JetWave 2450. You can see the basic information of JetWave 2450. This management interface provides five main options, which are Status, System, Wireless, Management and Tools. -
Page 26: Basic System Settings
Basic System Settings For users who use the JetWave 2450 for the first time, it is recommended that you begin configuration from “Basic Settings” in “System” shown below: Figure 14 Basic System Settings Basic Settings Ethernet DataRate: Adjust the data rate of Ethernet connection, including 10/100M full-duplex, half-duplex and Auto. -
Page 27: Figure 15 Ip Settings (Bridge)
IP Settings (Bridge) This is available only under Bridge network mode. Open “IP Settings (Bridge)” in “System” as below to configure the parameters for LAN which connects to the LAN port of JetWave 2450. In this page, users may change the settings for IP Address, Subnet Mask, and DHCP Server. Figure 15 IP Settings (Bridge) Obtain IP Address Automatically: If a DHCP server exists in your network, you can check this option, thus the JetWave 2450 is able to obtain IP settings automatically from that DHCP server. - Page 28 Figure 16 IP Settings (Router) WAN Settings: Specify the Internet access method to Static IP, DHCP or PPPOE. Users must enter WAN IP Address, Subnet Mask, Gateway settings provided by your ISPs. LAN Settings: When DHCP Server is disabled, users can specify IP address and subnet mask for JetWave 2450 manually.
-
Page 29: Radius Settings
RADIUS Settings RADIUS (Remote Authentication Dial-In User Service) is a server for remote user authentication and accounting; playing a central role in the network in providing the capabilities of authenticating, authorizing, accounting, auditing, alarming and etc. It allows an organization to maintain user profiles in a central database that all remote servers can share. -
Page 30: Time Settings
Time Settings Compliant with NTP, the JetWave 2450 is capable of keeping its time in complete accord with the Internet time. Make configuration in “Time Settings” from “System”. To use this feature, check “Enable NTP Client Update” in advance. Figure 18 Time Settings Time Zone Select Select the time zone from the dropdown list. - Page 31 Source IP Filtering: The source IP filtering gives users the ability to restrict certain types of data packets from your local network to Internet through JetWave 2450. Use of such filters can be helpful in securing or restricting your local network. Figure 19 Source IP Filtering Destination IP Filtering: The destination IP filtering gives you the ability to restrict the computers in LAN from accessing certain websites in WAN according to specified IP addresses.
- Page 32 Source Port Filtering: The source port filtering enable you to restrict certain ports of data packets from your local network to Internet through JetWave 2450. Use of such filters can be helpful in securing or restricting your local network. Figure 21 Source Port Filtering Destination Port Filtering: The destination port filtering enables you to restrict certain ports of data packets from your local network to Internet through JetWave 2450.
- Page 33 Port Forwarding: The port forwarding allows you to automatically redirect common network services to a specific machine behind the NAT firewall. These settings are only necessary if you wish to host some sort of server like a web server or mail server on the private local network behind JetWave 2450’s NAT firewall.
-
Page 34: Basic Wireless Settings
Basic Wireless Settings Open “Basic Settings” in “Wireless” as below to make basic wireless configuration. Figure 25 Basic Wireless Settings Disable Wireless LAN Interface Check this option to disable WLAN interface, then the wireless module of JetWave 2450 will stop working and no wireless device can connect to it. - Page 35 Wireless Network Name (SSID) This wireless network name is shared among all associated devices in your wireless network. Keep it identical on all those devices. Note that the SSID is case-sensitive and can not exceed 32 characters. Broadcast SSID Under AP mode, hiding network name is necessary when you are in a wireless environment that may have potential risk.
-
Page 36: Site Survey
Data Rate Usually “Auto” is preferred. Under this rate, the JetWave 2450 will automatically select the highest available rate to transmit. In some cases, however, like where there is no great demand for speed, you can have a relatively-low transmit rate for compromise of a long distance. Channel Mode Two levels are available: 20MHz and 40MHz. -
Page 37: Chapter 4 Advanced Settings
Chapter 4 Advanced Settings Advanced Wireless Settings Open “Advanced Settings” in “Wireless” to make advanced wireless settings. © Figure 27 Advanced Wireless Settings WMM Support WMM (Wi-Fi Multimedia) is a subset of 802.11e. It allows wireless communication to define a priority limit on the basis of data type under AP mode only, thus those time-sensitive data, like video/audio data, may own a higher priority than common one. - Page 38 Short GI Under 802.11n mode, enable it to obtain better data rate if there is no negative compatibility issue. RTS Threshold The JetWave 2450 sends RTS (Request to Send) frames to certain receiving station and negotiates the sending of a data frame. After receiving an RTS, that STA responds with a CTS (Clear to Send) frame to acknowledge the right to start transmission.
- Page 39 Link Integration Available under AP/Bridge/AP repeater mode, it monitors the connection on the Ethernet port by checking “Enabled”. It can inform the associating wireless clients as soon as the disconnection occurs. Max. Station Num Available only under AP mode, it defines the maximum amount of wireless clients allowed to be connected.
-
Page 40: Wireless Security Settings
Wireless Security Settings To prevent unauthorized radios from accessing data transmitting over the connectivity, the JetWave 2450 provides you with rock solid security settings. Security Settings Open “Security Settings” in “Wireless” as below: Figure 28 Security Settings Network Authentication Open System: It allows any device to join the network without performing any security check. Shared Key: Data encryption and key are required for wireless authentication. - Page 41 WPA&WPA2 with RADIUS: It provides options of WPA (TKIP) or WPA2 (AES) for the client. If it is selected, the data encryption type must be TKIP + AES and the RADIUS server must be set. WPA-PSK: It is a simplified WPA mode with no need for specific authentication server. In this so-called WPA Pre-Shared Key, all you have to do is just pre-enter a key in each WLAN node and this is the common way to be adopted in large and middle enterprise as well as residential network.
-
Page 42: Access Control
Access Control The Access Control appoints the authority to wireless client on accessing JetWave 2450, thus a further security mechanism is provided. This function is available only under AP mode. Open “Access Control” in “Wireless” as below. Figure 29 Access Control Access Control Mode If you select “Allow Listed”, only those clients whose wireless MAC addresses are in the access control list will be able to connect to your AP. -
Page 43: Wds Settings
WDS Settings Extend the range of your network without having to use cables to link the Access Points by using the Wireless Distribution System (WDS): Put simply, you can link the Access Points wirelessly. Open “WDS Settings” in “Wireless” as below: Figure 30 WDS Settings Enter the MAC address of another AP you wirelessly want to connect to into the appropriate field and click “Apply”... -
Page 44: Chapter 5 Management
Chapter 5 Management SNMP Management The JetWave 2450 supports SNMP for convenient remote management. Open “SNMP Configuration” in “Management” shown below. Set the SNMP parameters and obtain MIB file before remote management. Figure 31 SNMP Configuration Enable SNMP Check this box to enable SNMP settings. Protocol Version Select the SNMP version, and keep it identical on the JetWave 2450 and the SNMP manager. -
Page 45: Configure Snmpv3 User Profile
Set Community Specify the password for the incoming Set requests from the management station. By default, it is set to private. Trap Destination Specify the IP address of the station to send the SNMP traps to. Trap Community Specify the password sent with each trap to the manager. By default, it is set to public and allows all requests. -
Page 46: Password
Password Specify a password for the SNMPv3 administrator or user. Only the SNMP commands carrying this password are allowed to access the JetWave 2450. Confirm Password Input that password again to make sure it is your desired one. Access Type Select “Read Only”... -
Page 47: Upgrade Firmware
Upgrade Firmware Open “Firmware Upload” in “Management” and follow the steps below to upgrade firmware locally or remotely through JetWave 2450’s Web: © Figure 34 Upgrade Firmware Click “Browse” to select the firmware file you would like to load; Click “Upload” to start the upload process; Wait a moment, the system will reboot after successful upgrade. -
Page 48: Restore Factory Default Settings
Backup Settings By clicking “Save” a dialog box will popup. Save it, then the configuration file like ap.cfg will be saved to your local computer. Retrieve Settings By clicking “Browse” a file selection menu will appear, select the file you want to load, like ap.cfg; Click “Upload”... -
Page 49: System Log
Figure 37 Reboot System Log System log is used for recording events occurred on the JetWave 2450, including station connection, disconnection, system reboot and etc. Open “System Log” in “Tools” as below. Figure 38 System Log Remote Syslog Server Enable Remote Syslog: Enable System log or not. IP Address: Specify the IP address of the server. -
Page 50: Chapter 6 Status
Chapter 6 Status View JetWave 2450 Basic Information Open “Information” in “Status” to check the basic information of JetWave 2450, which is read only. Click “Refresh” at the bottom to have the real-time information. Figure 39 Basic Information Association List Open “Association List”... -
Page 51: View Network Flow Statistics
View Network Flow Statistics Open “Network Flow” in “Status” to check the data packets received on and transmitted from the wireless and Ethernet ports. Click “Refresh” to view current statistics. Figure 41 Network Flow Statistics Poll Interval Specify the refresh time interval in the box beside “Poll Interval” and click “Set Interval” to save settings. -
Page 52: View Arp Table
View ARP Table Open “ARP Table” in “Status” as below. Click “Refresh” to view current table. Figure 43 ARP Table View Active DHCP Client Table Open “DHCP Client List” in “Status” as below to check the assigned IP address, MAC address and time expired for each DHCP leased client. -
Page 53: Chapter 7 Troubleshooting
Q 1. How to know the MAC address of JetWave 2450? MAC Address distinguishes itself by the unique identity among network devices. For Korenix products, the MAC Address is 001277-XXXXXX. There are two ways available to know it. - Page 54 Q 5. What if the wireless connection is not stable after associating with an AP under wireless client mode? • Since the JetWave 2450 comes with a built-in directional antenna, it is recommended make the JetWave 2450 face to the direction where the AP is to get the best connection quality. •...
-
Page 55: Appendix A. Ascii
Appendix A. ASCII WEP can be configured with a 64-bit or 128-bit Shared Key (hexadecimal number or ACSII). As defined, hexadecimal number is represented by 0-9, A-F or a-f; ACSII is represented by 0-9, A-F, a-f or punctuation. Each one consists of two-digit hexadecimal. Table 2 ACSII ASCII ASCII... -
Page 56: Appendix B. Gpl Declamation
Appendix B. GPL Declamation PUBLIC SOFTWARE DECLAMATION In the software we delivered, there may contains some public software, if it is, please read below carefully: 1. Definition “Public Software”, when applicable, shall mean that portion of the Licensed Software, in source code form, set forth in the below Table, and provided under the terms set forth in the Section 5, the indicated website, the complete license terms can be found. - Page 57 to any such Public Software, as set forth in its presentation on website. 3. Limited Liability The supplier hereby express that the supplier shall have no liability for any costs, loss or damages resulting from Licensee’s breach of the terms and conditions applicable to use, conversion or combination of the licensed software with or into Public Software.
- Page 58 ourceforg e/bridge/br idge-utils- 1.0.6.tar.gz dropbear Copyright http://matt. GNU GENERAL PUBLIC http://www.gnu.o 2002-2006 Matt ucc.asn.au LICENSE Version 2 rg/licenses/old-li Johnston /dropbear/ censes/gpl-2.0.ht Portions copyright (c) dropbear- 2004 Mihnea 0.51.tar.bz Stoenescu hostapd Copyright http://host GNU GENERAL PUBLIC http://www.gnu.o 2002-2006, Jouni ap.epitest. LICENSE Version 2 rg/licenses/old-li Malinen fi/releases/...
- Page 59 vans/vsftp d-1.1.2.tar. linux ftp://ftp.ker GNU GENERAL PUBLIC http://www.gnu.o nel.org/pu LICENSE Version 2 rg/licenses/old-li b/linux/ker censes/gpl-2.0.ht nel/v2.6/lin ux-2.6.20.3 .tar.bz2 Appendix B. GPL Declamation Page 49...