Sony CCD-TRV118 Service Manual page 9

CCD-TRV118/TRV218E/TRV318/TRV418/TRV418E
1-5-4. Self-diagnosis Code Table
Self-diagnosis Code
Block Detailed
Function Code
C 0 4 0
C 2 1 0
C 2 2 0
C 3 1 1
C 3 1 1
C 3 1 2
C 3 1 2
C 3 1 2
C 3 1 2
C 3 1 2
C 3 1 3
C 3 1 4
C 3 1 4
C 3 1 1
C 3 1 1
C 3 2 2
C 3 2 2
C 3 2 2
C 3 2 2
C 3 2 2
C 3 2 3
C 3 2 4
C 3 2 4
E 6 1 0
E 6 1 1
E 6 2 0
E 6 2 0
*1: STEADYSHOT model (CCD-TRV318/TRV418/TRV418E)
Symptom/State
0 Non-standard battery is used.
0 Condensation.
0 Video head is dirty.
LOAD direction. Loading does not
0
complete within specified time
UNLOAD direction. Loading does not
1
complete within specified time
0 T reel side tape slacking when unloading.
Winding S reel fault when counting the
1
rest of tape.
2 T reel fault.
3 S reel fault.
4 T reel fault.
0 FG fault when starting capstan.
0 FG fault when starting drum.
2 FG fault during normal drum operations.
LOAD direction loading motor time-
0
out.
UNLOAD direction loading motor
1
time-out.
T reel side tape slacking when
0
unloading.
Winding S reel fault when counting the
1
rest of tape.
2 T reel fault.
3 S reel fault.
4 T reel fault.
0
FG fault when starting capstan.
0 FG fault when starting drum
FG fault during normal drum
2
operations
Difficult to adjust focus
0
(Cannot initialize focus.)
Zoom operations fault
0
(Cannot initialize zoom lens.)
Steadyshot function does not work well.
0 (With pitch angular velocity sensor output
stopped.)
Steadyshot function does not work well.
1 (With yaw angular velocity sensor output
stopped.)
Use the info LITHIUM battery.
Remove the cassette, and insert it again after one hour.
Clean with the optional cleaning cassette.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Inspect the lens block focus reset sensor (Pin qs of VC-303 board
CN301) when focusing is performed when the control dial is rotated
in the focus manual mode, and the focus motor drive circuit (IC301
of VC-303 board) when the focusing is not performed.
Inspect the lens block zoom reset sensor (Pin qg of VC-303 board
CN301) when zooming is performed when the zoom switch is
operated and the zoom motor drive circuit (IC301 of VC-303 board)
when zooming is not performed.
Inspect pitch angular velocity sensor (SE751 of SI-035 board)
peripheral circuits. *1
Inspect yaw angular velocity sensor (SE752 of SI-035 board)
peripheral circuits. *1
1-4E
Correction