Part View; Tone Tab; Level/Ch Tab - Roland Integra-7 Parameter Manual

Studio Set –

TONE tab

PART VIEW

1.
In the top screen, press the
The PART VIEW -ALL- screen appears .
* Some of the part parameters are not shown in the
PART VIEW -ALL- screen .
2.
[PART VIEW]
Press the
The PART VIEW screen appears .
Parameter
TONE tab
Tone Type
Tone Bank
Tone Number

LEVEL/CH tab

Level
(Also valid for the Ext part)
Pan
Cho Send Level
(Also valid for the Ext part)
Rev Send Level
(Also valid for the Ext part)
Output Assign
Rx Switch
Rx Channel
Mono/Poly
6
[PART VIEW] button .
button again .
Value
SN-A, SN-S, SN-D
PCMS, PCMD
PRST, USER,
GM2 (GM2#),
ExSN1–ExSN6,
SRX01–SRX12,
ExPCM
001–
0–127
L64–63R
0–127
0–127
A, B, C, D, 1–8
OFF, ON
1–16
MONO, POLY, TONE
Explanation
SN-A : SuperNATURAL Acoustic Tones
SN-S : SuperNATURAL Synth Tones
SN-D : SuperNATURAL Drum Kits
PCMS : PCM Synth Tones
PCMD : PCM Drum Kits
Specifies the type of tone/drum kit assigned to each part .
Selects the group of the tone/drum kit assigned to each part .
• ExSN1–5 can be selected as SN-A if that expansion is loaded
•
ExSN6 can be selected as SN-D if that expansion is loaded
•
SRX01–12 and ExPCM can be selected as PCMS and PCMD if that expansion is loaded
Selects the number of the tone/drum kit assigned to each part .
Adjust the volume of each part .
This setting's main purpose is to adjust the volume balance between parts .
Adjust the pan of each part .
"L64" "0" "63R"
is far left, is center, and
* If motional surround is on, surround output will be enabled and this setting will be ignored .
Adjusts the amount of Chorus for each Part .
If you don't want to add the Chorus effect, set it to 0 .
* This has no effect if motional surround is on .
Adjusts the amount of Reverb for each Part .
If you don't want to add the Reverb effect, set it to 0 .
*
This has no effect if motional surround is on .
Specifies for each part how the sound will be output .
A, B, C, D: The sound will be output in stereo to the OUTPUT A (MIX) jacks or from the OUTPUT B,
C, D jacks .
1–8: The sound will be output in monaural to the INDIVIDUAL 1–8 jacks .
For each part, specify whether MIDI messages will be received (ON), or not (OFF) .
If this is "OFF," the part will not respond . Normally, you should leave this
"OFF" when you do not want a specific part to be playing during song playback .
Specifies the MIDI receive channel for each part .
Set this parameter to "MONO" when the tone assigned to the part is to be played monophonically,
"POLY"
or to when the tone is to be played polyphonically . If you want to use the Mono/Poly
setting of the tone assigned to the part (p . **), set this to
* This is not shown in PART VIEW -ALL- .
SN-A SN-A SN-A
(Ac .Piano) (Organ) (Other)
–
ü
is far right .
"ON,"
"TONE."
SN-S SN-D
–
ü ü
but you can turn it
PCMS PCMD
–
ü