Auto Wah; Speaker Simulator - Roland Integra-7 Parameter Manual

05: Enhancer
Controls the overtone structure of the high frequencies, adding
sparkle and tightness to the sound .
L in Enhancer
R in
Enhancer
Parameter Value
Sens # 0–127
Mix #
0–127
Low Gain -15–+15 dB
High Gain -15–+15 dB
Level 0–127

06: Auto Wah

Cyclically controls a filter to create cyclic change in timbre .
L in
Auto Wah
R in
Auto Wah
Parameter Value
Filter Type
LPF, BPF
Manual #
0–127
Peak 0–127
Sens # 0–127
Polarity UP, DOWN
0 .05–10 .00 Hz,
Rate #
note
Depth # 0–127
Phase #
0–180 deg
Low Gain -15–+15 dB
High Gain -15–+15 dB
Level 0–127
2-Band
L out
EQ
Mix
2-Band
R out
EQ
Mix
Explanation
Sensitivity of the enhancer
Level of the overtones generated by
the enhancer
Gain of the low range
Gain of the high range
Output Level
L out
2-Band EQ
R out
2-Band EQ
Explanation
Type of filter
LPF: The wah effect will be applied
over a wide frequency range .
BPF: The wah effect will be applied
over a narrow frequency range .
Adjusts the center frequency at
which the effect is applied .
Adjusts the amount of the wah
effect that will occur in the range of
the center frequency .
Set a higher value for Q to narrow
the range to be affected .
Adjusts the sensitivity with which
the filter is controlled .
Sets the direction in which the
frequency will change when the
auto-wah filter is modulated .
UP: The filter will change toward a
higher frequency .
DOWN: The filter will change toward
a lower frequency .
Frequency of modulation
Depth of modulation
Adjusts the degree of phase shift of
the left and right sounds when the
wah effect is applied .
Gain of the low range
Gain of the high range
Output Level
07: Humanizer
Adds a vowel character to the sound, making it similar to a human
voice .
L in
Overdrive
R in
Parameter Value
Drive Sw OFF, ON
Drive # 0–127
Vowel1 a, e, i, o, u
Vowel2 a, e, i, o, u
0 .05–10 .00 Hz,
Rate #
note
Depth # 0–127
Input Sync Sw OFF, ON
Input Sync
0–127
Threshold
Manual #
0–100
Low Gain -15–+15 dB
High Gain
-15–+15 dB
Pan # L64–63R
Level
0–127

08: Speaker Simulator

Simulates the speaker type and mic settings used to record the
speaker sound .
L in
Speaker
R in
Speaker
Parameter Value
(See the table
Type
right .)
Mic Setting 1, 2, 3
Mic Level #
0–127
Direct Level # 0–127
Level #
0–127
MFX Parameters
Pan L
2-Band
Formant
EQ
Pan R
Explanation
Turns Drive on/off .
Degree of distortion
Also changes the volume .
Selects the vowel .
Frequency at which the two vowels
switch
Effect depth
LFO reset on/off
Determines whether the LFO for
switching the vowels is reset by the
input signal (ON) or not (OFF) .
Volume level at which reset is
applied
Point at which Vowel 1/2 switch
49 or less: Vowel 1 will have a
longer duration .
50: Vowel 1 and 2 will be of equal
duration .
51 or more: Vowel 2 will have a
longer duration .
Gain of the low frequency range
Gain of the high frequency range
Stereo location of the output
Output level
L out
R out
Explanation
Type of speaker
Adjusts the location of the mic
that is recording the sound of the
speaker .
This can be adjusted in three steps,
with the mic becoming more distant
in the order of 1, 2, and 3 .
Volume of the microphone
Volume of the direct sound
Output Level
L out
R out
75