Tva Env Tab; Output Tab; Comp Tab - Roland Integra-7 Parameter Manual

Parameter
Level V-Sens
Partial Pan
Random Pan Depth
Alternate Pan Depth
Relative Level

TVA ENV tab

TVA Env T1 V-Sens
TVA Env T4 V-Sens
TVA Env Time 1–4
TVA Env Level 1–3

OUTPUT tab

Partial Output Assign
Partial Output Level
Partial Chorus Send Level
Partial Reverb Send Level

COMP tab

* COMP+EQ can be used only for the part specified by Drum Comp+EQ Assign .
Comp 1–6 Switch
Comp 1–6 Attack Time
Comp 1–6 Release Time
Value
-63–+63
L64–63R
0–63
L63–63R
-64–+63
-63–+63
-63–+63
0–127
0–127
PART, COMP+EQ1–6
0–127
0–127
0–127
OFF, ON
0 .05–50 .0 ms
0 .05–2000 ms
Explanation
Set this when you want the volume of the drum partial to change depending on the force with
which you press the keys . Set this to a positive
volume increase the more forcefully the keys are played; to make the tone play more softly as you
play harder, set this to a negative "-"
Sets the pan for the drum partial . "L64"
MEMO
Set the Pan for Waves comprising the drum partials with the Wave Pan parameter (p . 67) .
Use this parameter when you want the stereo location to change randomly each time you press a
key . Higher settings will produce a greater amount of change .
NOTE
This will affect only waves whose Wave Random Pan Sw parameter (p . 67) is ON .
This setting causes panning to be alternated between left and right each time a key is pressed .
Higher settings will produce a greater amount of change .
in which the pan will alternate between left and right . For example if two drum partials are set to
"L" and "R" respectively, the panning of the two drum partials will alternate each time they are
played .
NOTE
This will affect only waves whose Wave Alter Pan Sw parameter (p . 67) is ON or REVS .
Corrects for the volume of the drum partial .
This parameter is set by the key-based controller system exclusive message . Normally, you should
leave it set to 0 .
NOTE
If the drum partial level is set to 127, the volume will not increase beyond that point .
This allows keyboard dynamics to affect the Time 1 of the TVA envelope . If you want Time 1 to be
speeded up for strongly played notes, set this parameter to a positive
"-"
slowed down, set this to a negative
The parameter to use when you want key release speed to control the Time 4 value of the TVA
envelope . If you want Time 4 to be speeded up for quickly released notes, set this parameter to a
"+"
positive value . If you want it to be slowed down, set this to a negative
Specify the TVA envelope times (Time 1–Time 4) . Higher settings will lengthen the time until the
next volume level is reached . (For example, Time 2 is the time over which Level 1 will change to
Level 2 .)
Specify the TVA envelope levels (Level 1–Level 3) . These settings specify how the volume will
change at each point, relative to the standard volume (the Partial Level value specified in the TVA
screen) .
T1 T2 T3
Level
L2
L1
Note on
T: Time L: Level
Specifies how the sound of each partial will be output .
Specifies the signal level of each partial .
Specifies the level of the signal sent to the chorus for each partial .
Specifies the level of the signal sent to the reverb for each partial .
Compressor on/off
Time from when the input exceeds the threshold until compression begins
Time from when the input falls below the threshold until compression is turned off
PCM Drum Kit (PCMD) –
"+" value to have the changes in drum partial
value .
is far left, "0" is center, and "63R"
"L" or "R" settings will reverse the order
"+"
value .
T4
L3
Note o
TVA ENV tab
is far right .
value . If you want it to be
"-"
value .
Time
71