Guitarampsim -> Delay - Roland Integra-7 Parameter Manual

MFX Parameters
Specifications of each Speaker Type
The speaker column indicates the diameter of each speaker unit (in
inches) and the number of units .
Type Cabinet
SMALL 1 small open-back enclosure 10
SMALL 2
small open-back enclosure 10
MIDDLE open back enclosure
JC-120
open back enclosure
BUILT-IN 1 open back enclosure
BUILT-IN 2
open back enclosure
BUILT-IN 3 open back enclosure
BUILT-IN 4
open back enclosure
BUILT-IN 5 open back enclosure
BG STACK 1
sealed enclosure
BG STACK 2 large sealed enclosure
MS STACK 1
large sealed enclosure
MS STACK 2 large sealed enclosure
METAL STACK large double stack
2-STACK large double stack
3-STACK
large triple stack
56: GuitarAmpSim -> Delay
L in
Pre Amp
Speaker
R in
Parameter Value
Amp Sw
OFF, ON
Type of guitar
Amp Type
amp
Amp Volume # 0–127
Amp Master # 0–127
LOW, MIDDLE,
Amp Gain
HIGH
Amp Bass
Amp Middle 0–127
Amp Treble
Delay Switch # OFF, ON
Delay Time # 0–1300 ms
Delay Feedback
-98–+98 %
#
200–8000 Hz,
Delay HF Damp
BYPASS
D100:0W–
Delay Balance #
D0:100W
92
Speaker Microphone
dynamic
dynamic
12 x 1 dynamic
12 x 2 dynamic
12 x 2 dynamic
12 x 2 condenser
12 x 2 condenser
12 x 2 condenser
12 x 2 condenser
12 x 2 condenser
12 x 2 condenser
12 x 4 condenser
12 x 4 condenser
12 x 4 condenser
12 x 4 condenser
12 x 4 condenser
Balance D
L out
Balance W
Delay
Balance W
Feedback
R out
Balance D
Explanation
Turns the amp switch on/off .
JC-120, CLEAN TWIN, MATCH DRIVE,
BG LEAD, MS1959I, MS1959II,
MS1959I+II, SLDN LEAD, METAL5150,
METAL LEAD, OD-1, OD-2, TURBO,
DISTORTION, FUZZ
Volume and amount of distortion
of the amp
Volume of the entire pre-amp
Amount of pre-amp distortion
Tone of the bass/mid/treble
frequency range
* "Match
Middle cannot be set if
Drive" is selected as the Pre Amp
Type .
Delay on/off
Adjusts the delay time from the
direct sound until the delay sound
is heard .
Adjusts the proportion of the delay
sound that is fed back into the
effect . Negative "-" settings will
invert the phase .
Frequency at which the high-
frequency portion of the delay
sound will be cut (BYPASS: no cut)
Adjusts the volume balance
between the sound that is sent
through the delay (W) and the
sound that is not sent through the
delay (D) .
Parameter Value
Speaker Sw
OFF, ON
(See the table
Speaker Type
below .)
Level 0–127
Specifications of each Speaker Type
The speaker column indicates the diameter of each speaker unit (in
inches) and the number of units .
Type Cabinet
SMALL 1 small open-back enclosure 10
SMALL 2 small open-back enclosure 10
MIDDLE open back enclosure
JC-120 open back enclosure
BUILT-IN 1 open back enclosure
BUILT-IN 2 open back enclosure
BUILT-IN 3 open back enclosure
BUILT-IN 4 open back enclosure
BUILT-IN 5 open back enclosure
BG STACK 1 sealed enclosure
BG STACK 2 large sealed enclosure
MS STACK 1 large sealed enclosure
MS STACK 2 large sealed enclosure
METAL STACK large double stack
2-STACK large double stack
3-STACK large triple stack
Explanation
Selects whether the sound will be
sent through the speaker simulation
(ON) or not (OFF)
Type of speaker
Output Level
Speaker Microphone
dynamic
dynamic
12 x 1 dynamic
12 x 2 dynamic
12 x 2 dynamic
12 x 2 condenser
12 x 2 condenser
12 x 2 condenser
12 x 2 condenser
12 x 2 condenser
12 x 2 condenser
12 x 4 condenser
12 x 4 condenser
12 x 4 condenser
12 x 4 condenser
12 x 4 condenser