Low Boost; Step Filter - Roland Integra-7 Parameter Manual

MFX Parameters
01: Equalizer
This is a four-band stereo equalizer (low, mid x 2, high) .
L in
4-Band EQ
R in
4-Band EQ
Parameter Value
Low Freq 200, 400 Hz
Low Gain # -15–+15 dB
Mid1 Freq 200–8000 Hz
Mid1 Gain -15–+15 dB
0 .5, 1 .0, 2 .0, 4 .0,
Mid1 Q
8 .0
Mid2 Freq 200–8000 Hz
Mid2 Gain -15–+15 dB
0 .5, 1 .0, 2 .0, 4 .0,
Mid2 Q
8 .0
2000, 4000, 8000
High Freq
Hz
High Gain # -15–+15 dB
Level # 0–127
02: Spectrum
This is a stereo spectrum . Spectrum is a type of filter which modifies
the timbre by boosting or cutting the level at specific frequencies .
L in
Spectrum
R in
Spectrum
Parameter Value
Band1 (250 Hz)
Band2 (500 Hz)
Band3 (1000 Hz)
Band4 (1250 Hz)
-15–+15 dB
Band5 (2000 Hz)
Band6 (3150 Hz)
Band7 (4000 Hz)
Band8 (8000 Hz)
0 .5, 1 .0, 2 .0, 4 .0,
Q
8 .0
Level # 0–127
74
L out
R out
Explanation
Frequency of the low range
Gain of the low range
Frequency of the middle range 1
Gain of the middle range 1
Width of the middle range 1
Set a higher value for Q to narrow
the range to be affected .
Frequency of the middle range 2
Gain of the middle range 2
Width of the middle range 2
Set a higher value for Q to narrow
the range to be affected .
Frequency of the high range
Gain of the high range
Output Level
L out
R out
Explanation
Gain of each frequency band
Simultaneously adjusts the width
of the adjusted ranges for all the
frequency bands .
Output Level

03: Low Boost

Boosts the volume of the lower range, creating powerful lows .
L in
Low Boost
R in
Low Boost
Parameter Value
Boost Frequency
50–125 Hz
#
Boost Gain # 0–+12 dB
WIDE, MID,
Boost Width
NARROW
Low Gain -15–+15 dB
High Gain -15–+15 dB
Level 0–127

04: Step Filter

This is a filter whose cutoff frequency can be modulated in steps . You
can specify the pattern by which the cutoff frequency will change .
You can use MFX CONTROL to restart the step sequence from the
beginning (p . 97) .
L in
Step Filter
R in
Step Filter
Parameter Value
Step 01 –16 0–127
0 .05 –10 .00 Hz,
Rate #
note
Attack # 0–127
LPF, BPF, HPF,
Filter Type
NOTCH
Filter Slope
-12, -24, -36 dB
Filter Resonance
0–127
#
Filter Gain 0–+12 dB
Level 0–127
L out
2-Band EQ
R out
2-Band EQ
Explanation
Center frequency at which the lower
range will be boosted
Amount by which the lower range
will be boosted
Width of the lower range that will
be boosted
Gain of the low frequency range
Gain of the high frequency range
Output level
L out
R out
Explanation
Cutoff frequency at each step
Rate of modulation
Speed at which the cutoff frequency
changes between steps
Filter type
Frequency range that will pass
through each filter
LPF: frequencies below the cutoff
BPF: frequencies in the region of
the cutoff
HPF: frequencies above the cutoff
NOTCH: frequencies other than the
region of the cutoff
Amount of attenuation per octave
-12 dB: gentle
-24 dB: steep
-36 dB: extremely steep
Filter resonance level
Increasing this value will emphasize
the region near the cutoff frequency .
Amount of boost for the filter output
Output level