007: St.p4Eq (Stereo Parametric 4-Band Eq) - Korg PS60 Parameter Manual

Effect Guide
Polarity
←
Threshold
←
Attack
←
Release
Side PEQ
PEQ Insert
Side PEQ
Trigger
Monitor
Side PEQ
PEQ Cutoff
[Hz]
Side PEQ Q
Side PEQ
Gain [dB]
←
Wet/Dry
Source
Amount
Threshold
Attack
Release
"Threshold" specifies the level where gating occurs when
"Envelope Select" is set to L/R Mix, L Only, or R Only.
"Attack" and "Release" specify the attack time and release
time of the gate.
Output Level
Threshold
Dry
Wet
Wet
Attack
Polarity
This inverts the polarity of the gate on/off operation. With
the "–" setting, the gate will close when the input signal
exceeds the specified level. The direction in which the
modulation source opens or closes the gate will also be
reversed.
86
Switches the polarity
+, –
of gating p.86
Sets the level where
0...100
gating is applied p.86
Sets the attack time
1...100
p.86
Sets the release time
1...100
p.86
Switches the trigger
Off, On signal equalizer on/
off p.85
Switches between
monitoring the effect
Off, On
output and the
trigger signal p.85
Sets the center
frequency of the
20...12.00k
equalizer for the
trigger signal p.85
Sets the bandwidth of
0.5...10.0 the equalizer for the
trigger signal p.85
Sets the gain of the
–18.0...+18.0 equalizer for the
trigger signal p.85
Sets the balance
Dry, 1 : 99...
between the effect
99 : 1, Wet
and the dry input
Selects a modulation
Off...Tempo
source for Wet/Dry
Sets the modulation
–100...+100
amount for Wet/Dry
Gate - Threshold
Louder
Input Level
Gate - Attack / Release
Threshold
Attack=1
Release=1
Attack=100
Release=100
Release
Delay Time [ms]
This sets the delay time for the input to the gate. When using
shorter Attack Time settings, you can lengthen the Delay
Time so that the sound is input after the gate opens.
007: St.P4EQ (Stereo Parametric 4-
Band EQ)
This is a stereo 4‐band parametric equalizer. You can select
peaking type or shelving type for Band 1 and 4. The gain of
Band 2 can be controlled by dynamic modulation.
Stereo In - Stereo Out
Left
Band1 Band2 Band3 Band4
PEQ
Trim
LEQ
LEQ
Trim
PEQ
Right
D -mod
Full Quick
Value
premiered parameter
←
Trim 0...100
Peaking,
Band1 Type B1Type Shelving-
Low
Peaking,
Band4 Type B4Type Shelving-
High
Band2
Dynamic Off...Tempo
Gain Source
Band2
Dynamic
–18.0...+18.0
Gain
Amount[dB]
Band1
B1 F[Hz] 20...1.00k
Cutoff [Hz]
Band1 Q B1 Q 0.5...10.0
Band1 –18.0...+18.0 Sets the gain of Band
B1 Gain[dB]
Gain [dB]
Band2
B2 F[Hz] 50...10.00k
Cutoff [Hz]
Band2 Q B2 Q 0.5...10.0
Band2 –18.0...+18.0 Sets the gain of Band
B2 Gain[dB]
Gain [dB]
Band3
B3 F[Hz] 300...10.00k
Cutoff [Hz]
Band3 Q B3 Q 0.5...10.0
Band3
B3 Gain[dB] –18.0...+18.0
Gain [dB]
Band4
B4 F[Hz] 500...20.00k
Cutoff [Hz]
Band4 Q B4 Q 0.5...10.0
Band4
B4 Gain[dB] –18.0...+18.0
Gain [dB]
Dry, 1 : 99...
←
Wet/Dry
99 : 1, Wet
Source Off...Tempo
Amount –100...+100
Band1 Type
Band4 Type
Selects a filter type for Band 1 and 4.
Wet / Dry
PEQ PEQ PEQ
HEQ
HEQ
PEQ PEQ PEQ
Wet / Dry
Explanation
Sets the input level
Selects the type of
Band 1 p.86
Selects the type of
Band 4 p.86
Selects the
modulation source of
the Band 2 gain p.87
Sets the modulation
amount of Band 2
gain p.87
Sets the center
frequency of Band 1
Sets the bandwidth of
Band 1 p.87
1
Sets the center
frequency of Band 2
Sets the bandwidth of
Band 2 p.87
2
Sets the center
frequency of Band 3
Sets the bandwidth of
Band 3 p.87
Sets the gain of Band
3
Sets the center
frequency of Band 4
Sets the bandwidth of
Band 4 p.87
Sets the gain of Band
4
Sets the balance
between the effect
and the dry input
Selects a modulation
source for Wet/Dry
Sets the modulation
amount for Wet/Dry