Timbre Mixer - Korg PS60 Parameter Manual

Performance Edit
Use Equal Temperament for programs whose multi‐
sample (ʺMultisample select,ʺ page 25) is set to mono:
0002, 00003, 0006, 0007, 0009, Stereo: 0001, or 0003 (i.e.,
the preload programs 13:SoloStretch Grand–15:SoloS‐
tretch Classic).
Key (Scale Key)
This selects the key of the specified scale.
This setting does not apply to the Equal Temperament,
Stretch, and User All Notes scales.
If you're using a scale other than Equal Temperament,
the performance of the selected scale and the Key set‐
ting may skew the tuning of the note. For example, A
above middle C might become 442 Hz, instead of the
normal 440 Hz. You can use the Global Mode's Master
Tune (page 70) parameter to correct this, if necessary.
Random
This parameter creates random variations in pitch for each
note. At the default value of 0, pitch will be completely sta‐
ble; higher values create more randomization.
This parameter is handy for simulating instruments that
have natural pitch instabilities, such as analog synths, tape‐
mechanism organs or acoustic instruments.

Timbre Mixer

Main Timbres (A. Piano–Synth):
Sub Timbres (A. Piano–Synth):
You can set the pan, and volume for each of the Timbres.
Pan
Pan (Pre)
This specifies the pan of each timbre.
Pan(Pre) CC#10
A.PIANO
IFX
E.PIANO
IFX
ORGAN
IFX
BRASS
IFX
STRINGS
IFX
L001...C064...R127: A setting of L001 is far left and R127 is
far right. A setting of C064 will reproduce the pan setting of
the Program Edit mode.
6
[RND, L001...C064...R127]
Pan(Post) CC#8
OSC1
Left Center
[C...B]
Left Center
OSC1
Left Center
[0...7]
Left Center
This pan setting is located immediately before the insert
effect. This means that if you select a mono effect for the
insert effect, this pan setting will be ignored. In this case, use
ʺPan (Post)ʺ to adjust the pan following the insert effect. For
programs of the STRINGS timbre, only this ʺPan (Pre)ʺ set‐
ting can be used; they will not be affected by an insert effect
( "Mixer" on page 82).
RND: The oscillator pan will change randomly at each note‐
on.
If Status (page 7) is set to INT, CC#10 (pan) messages
can be received to control the setting. CC#10 values of 0
or 1 will place the sound at the far left, 64 at center, and
127 at the far right. (exclude RND) Pan settings can be
controlled by messages received on the "MIDI Chan‐
nel" (page 7).
Pan (Pre)
This specifies the pan following the insert effect.
The STRINGS timbre does not have this parameter.
This parameter is controlled by CC#8. Control mes‐
sages are received on the channel specified by each tim‐
breʹs ʺMIDI Ch (MIDI Channel).ʺ Since the main timbre
and sub timbre of the same category use the same ʺPan
(Post)ʺ setting, this parameter can be controlled on the
ʺMIDI Ch (MIDI Channel)ʺ of both main and sub tim‐
bres.
Send
Modulation
Reverb/Delay
("Send1 (Mod)", "Send2 (Rev)" on page 4)
OSC2 OSC1
OSC1:
Amp1 Pan=L001
OSC2:
Right Amp2 Pan=R127 Left Center
Pan (CC#10)
C064
L032
L001
R096
R127
Left Center
Right
OSC1:
OSC2
Amp1 Pan=C064
OSC2:
Right
Amp2 Pan=C064
Pan (CC#10)
C064
L032
L001
R096
R127
Right
[RND, L001...C064...R127]
OSC2
OSC1:
Amp1 Pan=L032
OSC2:
Right Amp2 Pan=R096
Pan (CC#10)
C064
L032
L001
R096
R127
Right
[000...127]
[000...127]