Performance Edit; Panel - Korg PS60 Parameter Manual

Panel

The upper part of the PS60 Editor panel simulates the main
buttons and knobs of the PS60ʹs own front panel.
Mode Select, Utility
Mode button
To select a mode, click the button for the mode that you
want to edit.
PERF: Performance, Performance Edit
PROG EDIT: Program Edit
GLOB: Global
UTILITY
Here you can perform useful commands that are applicable
to each mode. Please see "UTILITY Command" on page 13.
Display
Performance Select
The display shows the performance bank and name. When
you click this, a browser will appear, allowing you to select
a performance from the list. Click the OK button to load the
performance. You can also switch performances by clicking
the symbols shown to the right of the name.
Tempo
The tempo is shown in the lower right side of the display. To
change the tempo setting, click the value to highlight it, and
then enter a value from the keyboard.
Performance Controls
Easy Setup [VOLUME, OCTAVE, MOD SEND,
Here you can specify the function that will be controlled by
each timbreʹs knob.
Timbre Control Knobs
Use these knobs to adjust the selected Easy Setup parameter
for each timbre.
Volume [000...127] (page 3)
Octave [‐5...+5] (page 3)
Send1 (Mod.) [000...127] (page 4)
Send2 (Rev) [000...127] (page 4)
Timbre On buttons
These buttons select the timbre(s) that will play. A button
will alternate on/off each time that you click it.
Note: These behave differently from the timbre ON buttons
of the PS60 itself.

Performance Edit

[PERF, PROG EDIT, GLOB]
[See Utility Command]
[A-1...D-5: Name]
[040.00...300.00]
REV/DLY SEND]
[On, Off]
Split Setting
Split Setting
This specifies the Split setting.
MAIN LOWER The main timbre will be assigned to the
lower region, and the sub timbre will be assigned to the
upper region.
MAIN UPPER The main timbre will be assigned to the
upper region, and the sub timbre will be assigned to the
lower region.
Choose either MAIN LOWER or MAIN UPPER, use ʺCTRLʺ
to choose either MAIN or SUB, and then use the Timbre On
buttons to select the timbres that you want to play.
OFF: The sub timbre will be off. The sub timbre settings will
still be remembered even if you press this button after
adjusting Split settings.
CTRL (Control)
When using Split settings, this selects which timbre will be
controlled; the main timbre or the sub timbre. Choose either
main or sub as the timbre that you want to select or control
using Easy Setup. You canʹt choose SUB if the Split Setting is
off.
Modulation
MOD TYPE button
Stereo Flanger, Vintage Cho/Flg, Stereo Phaser]
This selects the modulation effect type (page 117).
If you select No Effect, the output of the master effect will be
muted.
RATE knob
DEPTH knob
FB (FEEDBACK) knob
These parameters adjust the effect .
Reverb/Delay
REVERB/DELAY TYPE button
This selects the reverb/delay effect type (page 117).
If you select No Effect, the output of the master effect will be
muted.
TIME knob [0.1...10.00, 0.1...10.00, 0.1...3.0, 0...549]
LEVEL knob
FB (FEEDBACK) knob
These parameters adjust the effect.
[OFF, MAIN LOWER,
MAIN UPPER]
[MAIN, SUB]
[No Effect, Stereo Chorus,
[0.02...10.00]
[0...100]
[0...100]
[No Effect, Hall,
Plate, Room, Delay]
[0...100]
[0...100]
1