Korg PS60 Parameter Manual page 95

Step Base
...
Note
Times x1...x32
Step Base
...
Note
Times x1...x32
–Wet...
←
Wet/Dry –1 : 99, Dry,
1 : 99...Wet
Source Off...Tempo
Amount –100...+100
Phase [deg]
Offsetting the left and right phases alters how modulation is
applied to the left and right channels, creating a swelling
affect.
0 +90 +180 [degree]
–180 –90 0 [degree]
LFO Waveform
LFO Freq [Hz]
Step Freq [Hz]
When "LFO Waveform" is set to Step‐Tri, LFO is a step‐
shape, triangle waveform. The "LFO Freq [Hz]" parameter
sets the original triangle waveform speed. Changing the
"Step Freq [Hz]" parameter enables you to adjust the width
of the steps.
When "LFO Waveform" is set to Random, the "Step Freq
[Hz]" parameter uses a random LFO cycle.
LFO Frequency
Step Frequency
Step-Tri
BPM
Step Base Note
Times
The width of an LFO step, or a cycle of random LFO, is
obtained by multiplying the length of a note ( ... ) (selected
for "Step Base Note," in relation to the tempo specified in
"BPM," or the MIDI Clock tempo if "BPM" is set to MIDI)
by the number specified in the "Times" parameter.
Wet/Dry
The effect sound's phase will be reversed when you set this
parameter in the range of values from –Wet to –1:99.
IFX (Insert effects) List 014: St.RndFlt (Stereo Random Filter)
Selects the type of
notes that specify the
LFO speed p.91
Sets the number of
notes that specify the
LFO speed p.91
Selects the type of
notes to specify the
LFO step speed
p.91
Sets the number of
notes to specify the
LFO step speed
p.91
Sets the balance
between the effect
and the dry input
p.91
Selects a modulation
source for Wet/Dry
Sets the modulation
amount for Wet/Dry
LFO Phase
Random Filter LFO
Step Frequency
Random
015: St.MMFltr (Multi Mode Filter)
This is a multi‐mode filter with four types; low pass, high pass,
band pass, and band reject. You can use LFO or dynamic
modulation to vary the cutoff frequency or resonance.
Stereo In - Stereo Out
Left
Multimode Filter
Trim
LPF
HPF
Filter Type
BPF
BRF
Multimode Filter
Trim
Right
LFO: Tri / Sine LFO Shape
Full Quick
Value
parameter parameter
Trim 0...100
LPF, HPF, BPF,
Filter Type FilterType
BRF
←
Cutoff 0...100
Source Off...Tempo
Amount –100...+100
←
Resonance 0...100
Source Off...Tempo
Amount –100...+100
LFO Triangle,
Waveform Sine
←
Phase [deg] –180...+180
Depth Depth 0...100
LFO Freq
LFO [Hz] 0.02...20.00
[Hz]
Source Off...Tempo
–20.00...
Amount
+20.00
BPM/MIDI LFO MIDI
Off, On
Sync Sync
MIDI,
BPM 40.00...
300.00
Base Note ...
Times x1...x32
←
Drive SW Off, On
Output Level DriveLevel 0...100
←
Drive Gain 0...100
←
Low Boost 0...100
Dry, 1 : 99...
←
Wet/Dry
99 : 1, Wet
Source Off...Tempo
Wet / Dry
Driver
Output
Driver
Output
Wet / Dry
LFO Phase
Explanation
Sets the input level
Selects the type of
filter
Sets the cutoff
frequency (center
frequency)
Selects the
modulation source of
the cutoff
Sets the modulation
amount of the cutoff
Sets the resonance
amount
Selects the source that
will modulate the
amount of resonance
Sets the amount by
which the resonance
will be modulated
Selects the LFO
Waveform
Sets the LFO phase
difference between the
left and right p.91
Sets the depth of how
the LFO will modulate
the cutoff frequency
Sets the speed of the
LFO p.91
Selects a modulation
source for LFO speed
Sets the modulation
amount of LFO speed
When this is on, the
LFO speed is set by
BPM, Base Note, and
Times, instead of
Frequency p.89
MIDI syncs to the system
tempo; 40–300 sets the
tempo manually for this
individual effect p.89
Selects the type of
notes that specify the
LFO speed p.89
Sets the number of
notes that specify the
LFO speed p.89
Switches distortion
on/off within the filter
Sets the output level
Sets the distortion
amount
Sets the amount of
low-range boost
Sets the balance
between the effect
and the dry input
Selects a modulation
source for Wet/Dry
91