Download Print this page

Korg PS60 Parameter Manual: St.decimt (stereo Decimator)

Performance synthesizer.
Hide thumbs

Advertisement

Voice Top
Voice Center
Voice Bottom
These parameters assign vowels to the top, center, and 
bottom position of the controller.
E.g.: When "Voice Top"=A, "Voice Center"=I, and "Voice 
Bottom"=U:
If "Sweep Mode" is set to D‐mod is selected as the 
modulation source, moving your finger from the right to left 
of will change the sound from "a" to "i," then "u."
If Sweep Mode is set to LFO, the sound will change 
cyclically from "a" to "i," "u," "i," then "a."
Voice Bottom
A
U
JS X
D
-mod
JS +Y
– Max
JS –Y
etc...
Zero
Formant Shift
This parameter adjusts the frequency level where the effect 
is applied. If you wish to apply the effect to a higher‐range 
sound, set this parameter to a higher value; to apply the 
effect to a lower‐range sound, set this to a lower value.
Resonance
This parameter sets the intensity of resonance for the voice 
pattern. A larger value will add more character to the sound.

018: St.Decimt (Stereo Decimator)

This effect creates a rough sound like a cheap sampler by 
lowering the sampling frequency and data bit length. You 
can also simulate noise unique to a sampler (aliasing). 
Stereo In - Stereo Out
Left
Pre LPF
Resolution
Decimator
D
-mod
Sampling Frequency
LFO
Decimator
Pre LPF
Resolution
Right
Full
Quick
Value
parameter
parameter
Pre LPF
Off, On
Sampling
1.00k...
Fs [Hz]
Freq [Hz]
48.00k
Source
Off...Tempo
–48.00k...
Amount
+48.00k
Depth
LFO Depth
0...100
Source
Off...Tempo
Talking Modulator Control
Voice Center
Voice Top
A
I
E
O
+ Max
Zero
+ Max
Wet / Dry
High Damp Output Level
High Damp Output Level
Wet / Dry
Explanation
Selects whether the
harmonic noise caused
by a decrease in
sampling frequency is
generated or not
p.93
Sets the sampling
frequency
Selects the
modulation source of
the sampling
frequency
Sets the modulation
amount of the
sampling frequency
Sets the depth of the
sampling frequency
LFO modulation
Selects the LFO
modulation source of
the sampling frequency
IFX (Insert effects) List 018: St.Decimt (Stereo Decimator)
Amount
–100...+100
High Damp
0...100
[%]
Resolution
Bit Reso
4...24
[bit]
Output Level OutLevel
0...100
Source
Off...Tempo
–20.00...
Amount
+20.00
LFO Freq
LFO [Hz]
0.02...20.00
[Hz]
Source
Off...Tempo
Amount
–100...+100
BPM/MIDI
LFO MIDI
Off, On
Sync
Sync
MIDI,
BPM
40.00...
300.00
Base Note
...
Times
x1...x32
Dry, 1 : 99...
Wet/Dry
99 : 1, Wet
Source
Off...Tempo
Amount
–100...+100
Pre LPF
If a sampler with a very low sampling frequency receives very 
high‐pitched sound that could not be heard during playback, it 
could generate pitch noise that is unrelated to the original sound. 
Set "Pre LPF" to On to prevent this noise from being generated.
If you set the "Sampling Fre" to about 3 kHz and set "Pre 
LPF" to Off, you can create a sound like a ring modulator.
Resolution [bit]
Output Level
If you set a smaller value for the "Resolution" parameter, the 
sound may be distorted. The volume level may also be 
changed. Use "Output Level" to adjust the level.
Sets the LFO
modulation amount of
the sampling frequency
Sets the ratio of cut of
the high range
Sets the data bit
length
p.93
Sets the output level
p.93
Selects a modulation
source for LFO speed
Sets the modulation
amount of LFO speed
Sets the speed of the
LFO
Selects the
modulation source
for the output level
Sets the modulation
amount of the output
level
When this is on, the LFO
speed is set by BPM,
Base Note, and Times,
instead of Frequency
MIDI syncs to the
system tempo; 40–300
sets the tempo
manually for this
individual effect
Selects the type of
notes that specify the
LFO speed
Sets the number of
notes that specify the
LFO speed
Sets the balance
between the effect
and the dry input
Selects a modulation
source for Wet/Dry
Sets the modulation
amount for Wet/Dry
93

Advertisement

   Also See for Korg PS60

   Related Manuals for Korg PS60

Comments to this Manuals

Symbols: 0
Latest comments: