Vcs Configuration; H.323; Overview; About H.323 On The Vcs - TANDBERG VCS Administrator's Manual

Video communication server
Hide thumbs Also See for VCS:
Table of Contents

Advertisement

Grey Headline (continued)

H.323

H.323 Overview

About H.323 on the VCS

The VCS supports the H.323 protocol: it is an H.323 gatekeeper.
It will also provide
interworking
between H.323 and SIP,
translating between the two protocols to enable endpoints that
only support one of these protocols to call each other. In order
to support H.323, the
H.323 mode
must be enabled.

Using the VCS as an H.323 Gatekeeper

As an H.323 gatekeeper, the VCS accepts registrations from
H.323 endpoints and provides call control functions such as
address translation and admission control.

Configuring H.323 Ports

The VCS allows you to configure the listening port for H.323
registrations and call signaling, and the range of ports to be
used by H.323 calls once they are established.
The default VCS configuration uses standard port numbers so
you can use H.323 services out of the box without having to first
set these up.
Overview and
Introduction
Getting Started
Status
D14049.04
JULY 2008

Overview

H.323 endpoints in your network must register with the VCS in
order to use it as their gatekeeper.
There are two ways an H.323 endpoint can locate a VCS
with which to register: manually or automatically. The option
is configured on the endpoint itself under the
Discovery
setting (consult your endpoint manual for how to
access this setting).
If the mode is set to automatic, the endpoint will try to
register with any VCS it can find. It does this by sending out
a Gatekeeper Discovery Request, to which eligible VCSs will
respond.
If the mode is set to manual, you must specify the IP address
of the VCS with which you wish your endpoint to register, and
the endpoint will attempt to register with that VCS only.

Registration Conflict Mode

An H.323 endpoint may attempt to register with the VCS using
an alias that has already been registered on the VCS from
another IP address. The reasons for this could include:
two endpoints at different IP addresses are attempting to
register using the same alias
a single endpoint has previously registered using a particular
alias. The IP address allocated to the endpoint then changes,
and the endpoint is attempting to re-register using the same
alias.
You can determine how the VCS will behave in this situation by
configuring the
Registration Conflict
Reject
: denies the new registration.
Overwrite
: deletes the original registration and replaces it
with the new registration.
System
VCS
Zones and
Configuration
Configuration
Neighbors

H.323 Endpoint Registration

Auto Discover

The VCS has an
it will respond to the Gatekeeper Discovery Requests sent out by
endpoints.
To prevent H.323 endpoints being able to register automatically
Gatekeeper
with the VCS, set
endpoints will be able to register with the VCS only if they have
been configured with the VCS's IP address.

Time to Live

H.323 endpoints must periodically re-register with the VCS in
order to confirm that they are still functioning. The VCS allows
you to configure the interval (in seconds) between these re-
registrations, known as the
confirmation from the endpoint within the specified period, it will
send an IRQ to the endpoint to verify that it is still functioning.

Call Time to Live

Once the endpoint is in a call, the VCS will periodically poll it to
confirm whether it is still in the call. If the endpoint does not
Mode. The options are:
respond, the call will be disconnected.
The VCS allows you to configure the interval (in seconds) at
which the endpoints are polled, known as the
Call
Bandwidth
Processing
Control
65
TANDBERG
VIDEO COMMUNICATIONS SERVER
Auto Discover
setting which determines whether
Auto Discover
to
Off.
This will mean that
Time to
Live.
Some older endpoints do not support the ability to
periodically re-register with the system. In this case, and
in any other situation where the system has not had a
The system will poll endpoints in a call regardless of
whether the call type is traversal or non-traversal.
Firewall
Applications
Maintenance
Traversal
ADMINISTRATOR GUIDE
Call Time to
Live.
Appendices

Advertisement

Table of Contents
loading

Table of Contents