Pan And Routing - Midas VERONA Operator's Manual

48v -15
power pad
+30 +45
+15 +60
mic gain
O ins
mic
60
160
hi-pass
20 400
-15 +15
5k 10k
treble
Group sends are post channel equalisation, mute and fader.
2k 20k
The group sends can be configured in either of two modes:-
-15 +15
1k
3k
hi-mid
1. Pre-Pan (mono)
400 8k
300 1k
lo-mid
100 2k
-15 +15
2. Post-Pan (stereo)
50 100
bass
20 200
-15 +15
aux pre
eq eq
off on
This configuration is made by depressing the 'Groups Pan' key for stereo group operation or released for mono
0
aux 1 group mode.
+6
0
aux 2
This selection, however, is on a channel-by-channel basis and so some may be assigned to the groups as mono or
+6
as stereo depending upon the desired usage.
0
aux 3
+6
For example:
0
aux 4
+6
0
aux 5
+6
0
aux 6
+6
0
aux 7
pre
+6
0
aux 8
pre
+6
Group 1-8
groups
1-2
routes the channel signal to the group
3-4
busses as described above.
5-6
7-8
mono stereo
Mono - Depressing the mono switch routes
c
the channel signal to the mono buss (post-
EQ, mute and fader).
l r
pan
groups master
pan s i s
Pan - The pan control allows the channel
MUTE
signal to be positioned in a stereo field when
routed to the stereo buss or when group
SOLO
sends are configured to be stereo. The pan
control allows continuous adjustment of the
10
18
image from hard left, to hard right with a
12
5
0
centre detent and obeys a constant power
-18
law (i.e. -3dB at the centre so that the
0
output power remains at unity).
5
10 mute 1
Groups Pan
15
Verona's group sends may be configured by
mute 2
20
depressing the 'Groups Pan' key for stereo
mute 3
30
group operation or released for mono group
40
mute 4
mode.
MIDAS
Each group is sent the same mono signal.
i.e. Selecting 1, 2 & 3 will send to each group equally.
Each pair of groups behave as if they were stereo groups. The mono signal is positioned in a stereo field by
the pan control. The Left signal is routed to the odd numbered buss and the right to the even numbered
buss.
i.e. Selecting groups 1, 2 & 3 with pan hard left will result in signal being routed to groups 1 & 3 only.
Similarly, with pan hard right, signal will be sent only to group 2.
Application
Multitrack Recording
Alternative/Delay Output
- Depressing the group switch
- As described above the
Mono Input Channels Mono Input Channels

Pan and Routing

The Verona is a flexible mixing console with eight group buss outputs
plus stereo and mono outputs.
Groups
Signal can be routed to any of the eight group busses by depressing
the corresponding group select switch.
Config. Reason
Mono Inputs can be sent to a particular input on the multitrack recorder
without affecting the stereo image used at FOH.
Stereo The Group would behave in the same manner as the stereo
output allowing for separate levelcontrol but retaining the original
stereo image from FOH.
groups
1-2
3-4
5-6
7-8
mono stereo
c
l r
pan
groups master
pan s i s
MUTE
Operators Manual - Page 11
Stereo - Depressing the stereo switch
routes the channel signal to the stereo
(main left and right) buss (post-EQ, pan,
mute and fader).
Master SIS - The master SIS switch will
enable the spacial imaging
whereby the channel pan control operates
in a different way. When panned hard left,
signal is routed to the stereo left output as
normal, similarly when panned hard right,
the signal is routed to the stereo right
output as normal. However, when panned
centre, the signal is routed ONLY to the
mono output creating a LCR (left-centre-
right) system instead of the normal LR
(left-right) system.
You may use SIS mode if using a centre
speaker for speech or solo instruments
while retaining the stereo for backing
vocals and instruments.
Mute - The mute switch mutes the channel
signal. Note that signal will still be sent to
the insert point and to the direct output.
The mute status of the channel is indicated
by the corresponding mute LED
system