Midas VERONA Operator's Manual page 28

master meters
+21 +21 +21
+18 +18 +18
+15 +15 +15
+12 +12 +12
+9 +9 +9
+6 +6 +6
+3 +3 +3
0 0 0
-3 -3 -3
-6 -6 -6
-9 -9 -9
-12 -12 -12
-15 -15 -15
-18 -18 -18
-21 -21 -21
-24 -24 -24
left mono right
solo meters
The setting of this depends upon the circumstances (and the usage of the centre
left pfl right
+21 +21 +21
mono ouptut). For example, if an independent graphic EQ or limiter is required to
+18 +18 +18
+15 +15 +15
control the mono centre speaker, then it may not be required (or desired) to have
+12 +12 +12
+9 +9 +9
the graphic EQ/limiter inserted into the left and right output affect the mono
+6 +6 +6
+3 +3 +3 centre.
0 0 0
-3 -3 -3
-6 -6 -6
Mute
-9 -9 -9
-12 -12 -12
which mute the signal post fader.
-15 -15 -15
-18 -18 -18
-21 -21 -21
Solo
-24 -24 -24
150 500 0
AFL stereo busses.
50
5k +10
freq
tape
0
Output Level
mono
+10dB.
+10
generator
stereo
SOLO
on
3
1 2
NEUTRIK
+15 +60
talk
talk
on
mic
master
talk
external
solo in
place
groups
1
1-2
auto
3-4
2
5-6
mute
7-8
mono stereo
3
aux matrix
masters
4
pfl
SOLO
monitor
phones
local
0 0
+10 +10
MUTE MUTE
stereo pre
1
to mono insert
MUTE MUTE MUTE
left right mono
SOLO SOLO
stereo mono
2
10 10
5 5
0 0
3
5 5
masters
10 10
15 15 4
20 20
30 30
40 40
Again, these switches are a major function worthy of note (i.e. don't forget that you have them enabled and
the channels assigned or channel mutes will not be released).
- Each of the left right and centre outputs have individual channel mutes
- When depressed, the stereo or mono signal is routed to the PFL mono and
- Each output level is continuously variable from off (-inf) to
master WARNING: Solo in place is a major function and should be used for sound check
ONLY. Please read this information carefully!
solo in
Solo in Place - When depressed with a small object (eg. screwdriver or pencil tip), the solo
place
in place switch causes all active input solos on the console to be exclusively routed to the
main outputs of the console. (i.e. mute all un-soloed inputs).
i.e. If a solo is in place, only those active solos will be heard from the main front of house
auto
speakers. This is a major function worthy of note.
The solo in place function is more at home in studio surroundings where the engineer would
expect only to hear active solos through the monitors. It's uses in live sound reinforcement
mute
are limited but include:
At sound check, Solo In Place could be used to check or EQ (or adjust insertions,
effects etc.) for one or a number of channels at once without having to turn down or
mute each of the undesired channels (which may upset the onstage monitors an
hence the musicians!).
Auto Mute Masters
through 4) as assigned on the input channels.
Verona Master Outputs Verona Master Outputs
The controls on this page are those directly responsible
for the main outputs from the console.
Stereo to Mono
a sum of the stereo left and right
signals are routed to the mono
signal buss via the pre insert switch.
Pre Insert - When depressed, the
stereo signal sent to the mono buss
is sourced from the stereo signals
before the stereo insert points.
Otherwise the signal is taken after
the stereo inserts.
The tape input on the rear of the console can be
routed to the main mono or stereo busses by
pressing the Mono
of the tape input is continuously variable from off
(-inf) to +20dB (the nominal input level is
referenced to -10dB).
Solo - When depressed, the tape input signal is
routed to the stereo AFL and mono PFL busses.
- The auto mute masters are used to enable the mute groups (1
Operators Manual - Page 26
- When depressed,
stereo
to mono
MUTE
left
SOLO
stereo
Verona Features Verona Features
or Stereo switches. The level
pre
insert
MUTE MUTE
right mono
SOLO
mono
10 10
5 5
0 0
5 5
10 10
15 15
20 20
30 30
40 40
0
+10
tape
mono
stereo
SOLO