Midas VERONA Operator's Manual page 14

48v -15
power pad
+30 +45
+15 +60
mic gain
O ins
mic
60
160
hi-pass
20 400
Solo - When depressed, the channel signal
-15 +15
5k 10k
will be sent to the After Fade Listen (AFL)
treble
stereo and Pre Fade Listen (PFL) mono
2k 20k
outputs.
illuminate to show that the channel solo is
-15 +15
1k
3k
active.
hi-mid
400 8k
300 1k
The Left and Right Monitor and the PFL
lo-mid
console outputs can be used, for example,
100 2k
when operating from within a booth to hear
selected solos and not the whole FOH mix.
-15 +15
50 100
bass
20 200 Note: If Solo In Place is activated on the
console, any active input solos will replace
-15 +15
the master outputs completely until the solo
is removed.
aux pre
eq eq
off on
0
Channel Fader
aux 1
for continuous adjustment of the channel
+6
0
level from off (-inf) to +10dB.
aux 2
+6
0
At 0dB, the output of the channel to the
aux 3
Stereo, Mono and Group busses will be at
+6
0
unity (i.e. no boost or cut in level from the
aux 4
input).
+6
0
aux 5
+6
0
aux 6
+6
0
aux 7
pre
+6
0
aux 8
Mute 1,2,3 & 4
pre
+6
groups
console. To assign an input channel to an automute, switch in the desired mute switch.
1-2
3-4
Commonly, these are used to mute similar channels, for example:
5-6
7-8
mono stereo
c
l r
pan
groups master
pan s i s
MUTE
SOLO
Note that if any assigned automute or the channel mute is activated then the channel will be muted until all
assigned automutes and the channel mute are removed (i.e. the mutes work like a logical OR where any single or
combination of mutes will mute the channel output).
10
18
12
5
0
-18
0
5
10 mute 1
15
mute 2
20
mute 3
30
40
mute 4
MIDAS
The solo LED indicator
- The channel fader allows
- The Verona has four (4) automute busses that can be controlled from the centre section of the
Channels Reason
Drum Mics Allows the engineer to mute the whole drum kit at once.
Choir Overheads Allows the engineer to quickly remove all choir mics at once
Orchestra Parts Allows the engineer to zone mics together (e.g. Brass, Strings,
etc.) and mute sections together if they were not playing.
Mono Input Channels Mono Input Channels
SOLO
will
10
18
12
5
0
-18
0
5
mute 1
10
15
mute 2
20
mute 3
30
40
mute 4
Operators Manual - Page 12
4 LED Meter - Each input channel contains
in-channel monitoring allowing the user to
monitor the input signal without the need for
using the PFL.
The in-channel meter is especially useful
when setting the microphone gain of a
channel. Also, as the, meter is post-EQ, it is
possible to see the effect that the channel
equalisation has upon the level. It may be
necessary to turn the input gain down when
excessive EQ is used to prevent the channel
from overloading.
-18db - Signal Present
0dB - Normal Level
+12dB - High Level
+18dB - Overload (Peak)
Note: The LED meter and the direct output
are fed from the same source and are Post-
Insert and EQ but Pre-Fader and Mute. The
channel in-line meter and direct output are
unaffected by the channel
automutes.
mute or