Table of Contents
Advertisement
48V
-15
power
pad
+30
+45
+15
+60
mic gain
O
ins
mic
80Hz
hi-pass
0
+20
line gain
Mute 1,2,3 & 4
stereo
automute busses that can be controlled
mono
wide
image
from the centre section of the console. To
treble
assign an input channel to an automute,
switch in the desired mute switch.
-15
+15
Commonly, these are used to mute similar
-15
+15
3k
1k5
hi-mid
channels, for example:
600
8k
300
500
Channels
lo-mid
100
1k2
Drum Mics
-15
+15
bass
-15
+15
Choir Overheads Allows the engineer to
aux pre
eq
eq
off
on
0
Orchestra Parts
aux 1
+6
0
aux 2
+6
0
aux 3
+6
0
Note that if any assigned automute or the
aux 4
channel mute is activated then the channel
+6
0
will be muted until all assigned automutes
aux 5
+6
and the channel mute are removed (i.e. the
0
mutes work like a logical OR where any
aux 6
+6
single or combination of mutes will mute the
0
channel output).
aux 7
pre
+6
0
aux 8
pre
+6
groups
1-2
3-4
5-6
7-8
mono
stereo
c
I want direct outs for recording but multi function channels don't have any . . .
l
r
pan
The multi function channels don't have a specifically labelled direct output BUT, if you are using a microphone
groups
pan
input and don't need to use the insert channel, you can insert a standard unbalanced quarter-inch jack lead into
MUTE
the insert point and use this as a direct output. This will work on the condition that you do not activate the insert
stereo
point on the channel strip (the insert switch) as this will cause signal to the channel to be lost.
SOLO
To see for yourself why this works, look at the block diagrams later in the manual.
18
10
12
I'm running monitors from FOH and I've run out of auxes for effects . . .
0
5
-18
0
To add effects to a mono mic input on a multifunction channel, use the insert send of the channel into the effects
unit input and the stereo outputs of the effects unit into the stereo line inputs of the same channel on the Verona.
5
Use the mic gain for the mic and the line gain for the effect return level. Now the aux sends and channel fader will
control both the mic level and effects return level.
mute 1
10
15
mute 2
20
mute 3
30
40
mute 4
MIDAS
Multi Function Input Channels
Multi Function Input Channels
- The Verona has four (4)
Reason
Allows the engineer to
mute the whole drum kit
at once.
quickly remove all choir
mics at once
Allows the engineer to
zone mics together (e.g.
Brass, Strings, etc.) and
mute sections together if
they were not playing.
Multi Function Module hints & Tips
Operators Manual - Page 18
4 LED Meter
contains
in-channel
allowing the user to monitor the input
signal without the need for using the
PFL.
10
The in-channel meter is especially
18
useful when setting the microphone
12
gain of a channel. Also, as the, meter is
5
0
post-EQ, it is possible to see the effect
-18
that the channel equalisation has upon
the level. It may be necessary to turn
0
the input gain down when excessive EQ
is used to prevent the channel from
overloading.
5
Note: The LED meter is Post-Insert and
EQ but Pre-Fader and Mute.
mute 1
10
Channel Fader
allows for continuous adjustment of the
15
channel level from off (-inf) to +10dB.
mute 2
20
At 0dB, the output of the channel to the
mute 3
Stereo, Mono and Group busses will be
30
at unity (i.e. no boost or cut in level
from the input).
40
mute 4
- Each input channel
monitoring
- The channel fader
Hide quick links:
Advertisement
Table of Contents
