Advertisement
Available languages
Available languages
When selected, money h eld inescrow f or30minutes without further escrow
orcycle activity w illbecleared.
00
Not S elected "OFF."
CE Selected "ON."
Press DEI_ICATES
&KNITS keypad once forthis selection.
Press WOOI.ENS
keypad once toadvance tonext c ode.
r.800r.
800
TOP SPIN SPEED RPM
This can be selected from the following spin speeds: 600 rpm, 750 rpm,
800 rpm, 1000 (displays as 999) rpm.
Step between speeds by pressing PERMANENT PRESS.
Currently set for 800 rpm.
PressWOOLENS keypad once to advance to next code.
U.00
U.
PENNY INCREMENT
OFFSET
00
This represents
the penny increment
price offset used in
Generation
2 (Enhanced
Debit)
PR models.
Choose
from 0-4 pennies
by
pressing
the PERMANENT
PRESS keypad.
Press WOOI.ENS
keypad
once to advance
to next code.
A1.00
A1.
PREWASH LENGTH
00
This is the number
of minutes
of PREWASH.
Choose
0 to disable
the prewash
or select between
2 and 7 minutes
by
pressing
the PERMANENT
PRESS keypad.
Press WOOI_ENS
keypad
once to advance
to next code.
A2.03
A2.
FINAL SPIN LENGTH
03
This is the number
of minutes
of final high speed spin. Choose from
3-8 minutes
by pressing the PERMANENT
PRESS keypad.
Press WOOI.ENS
keypad
once to advance
to next code.
If cycle counter
(90C) is selected,
the following
is true:
100
Represents the number
of cycles
in HUNDREDS
200
Represents the number
of cycles
in ONES
Total = 225 cycles
This is "VIEW
ONI.Y"
and cannot
be cleared.
1 02 = 200
2 25 = 25
Press WOOI.ENS
keypad
once to advance
to next code.
If money counter
(1.0C or 1.C0) is selected,
the following
is true:
300
Number
of dollars
in HUNDREDS
400
Number
of dollars
in ONES
500
Number
of CENTS.
3 01 = 100
4 68 = 68
5 75 = 75
Total =$168.75
END of SETUP PROCEDURES.
EXIT FROM
SETUP MODE
PI]) Models:
Reinstall
access door.
PR Modem: Remove power,
open console,
reinsert
plug into AA1, close console,
and apply
power.
To enter the "Washer
Diagnostic
Mode,"
first enter "Start Operating
Setup." Then press and
hold the DEI_ICATES & KNITS key for 1 second
while
in any of the setup codes one through
six, anytime
a diagnostic
code is present,
or while
dAS displays
if operating
with Maytag
Data
Acquisition
setup.
On entry to diagnostic
mode the entire
display will flash, a cycle in process
is canceled,
money in escrow
is cleared,
and diagnostic
codes are cleared.
If a diagnostic
code persists, it
must be corrected
before the following
cycle options
are permitted.
There are five possible
ways to initiate
cycle activity
from diagnostic
mode
as follows:
1.
Clean Washer
cycle - With the entire
display flashing,
this cycle is started by pressing
the
BRIGHTS
keypad.
Use the Clean Washer
cycle once a month
to keep the inside of your washer
fresh and
clean. This cycle uses a higher water
level. Use with
AFFRESH r_ washer
cleaner
tablet or
liquid
chlorine
bleach
to thoroughly
clean the inside of your washing
machine.
This cycle
should
not be interrupted.
See "Cleaning
Your Washer."
IMPORTANT:
Do not place garments
or other items in the washer
during
the Clean
Washer
cycle.
Use this cycle with an empty wash drum.
2.
Cycle
Credit - With
the entire
display flashing,
a cycle may be credited
by pressing the
PERMANENT
PRESS keypad
(CC will display).
When
the service mode
is exited "SEI.ECT
CYCI E" will be displayed
unless the end-of-cycle
door opening
is required.
3.
Manual
I_oad Test Cycle
- With
the entire display
flashing,
this cycle is started by pressing
the WHITES
keypad.
This cycle provides
more typical
full length fills, tumbles,
drains and
actuator
dispenser
movement
allowing
for a more thorough
analysis
of the washer
operation,
including
pressure
switch
behavior.
4.
Quick
Spin Cycle
- With the entire
display flashing,
this cycle is started by pressing
the
COl_ORS
keypad.
This cycle provides
a method
to quickly
drain
and spin (remove
water
from the washer)
if desired.
5.
History
Overview
Test Cycle
- With
the entire
display flashing,
this cycle is started by
pressing the WOOI_ENS
keypad.
This cycle provides
a quick verification
that the cold and
hot water valves, dispensers,
and pump
motor
are working
and actuator
dispenser
movement.
It also includes
drain and spin operations.
Pressing the DELICATES & KNITS keypad
will exit diagnostic
mode and cancel
a diagnostic
cycle in process.
16
Advertisement
